Chiayo SM-5016 Manual de usuario
Operation manual
CHIAYO ELECTRONICS CO.,LTD.
SM-5016
UHF Belt-pack Transmitter
1
SM-5016 UHF Belt-pack Transmitter
Parts and functions
1.Antenna
2.Battery weak/audio mute indicator
3.Audio mute switch
4.Audio input connector (mini XLR)
5.LCD
6.Charging port
7.Cover release button
8.Power button
9.High-impedance gain control (GT)
10.Low-impedance gain control (MT)
11.Setting button
12.Up button
13.Down button
14.Battery compartment
15.Charging contacts
Battery installation & indicator
●►○
●
When the transmitter is switched ON, a red
LED ②will blink once to denote the batteries
installed are in good condition.
If the LED remains illuminated, it means the
batteries are weak and require replacement.
This transmitter requires 2 x AA batteries to
operate.
To install, remove the battery cover and slide
the batteries into the battery compartment &
replace the battery cover.
Note: Batteries contain a corrosive acid that may leak and damage the transmitter when stored for a long
period. Batteries should be removed from the transmitter before storing without use for more than 4 weeks.
8
12
9
11
10
13
14
15 15
1
234
6
5
7
2
Instructions
Channel setting
1 Use UP▲/ DOWN▼button to go to the
CHANNEL｜FREQUENCY page.
2 Press and hold the SET button for 2
seconds, then the upper-right channel
number will flash to allow changes to be
made.
3 Press UP▲/ DOWN▼buttons to change
the channel number. The corresponding
frequency will change accordingly.
4 After selecting a channel, press and hold
the SET button for 2 seconds or wait 9
seconds to save the setting.
Battery type setting
1 Use UP▲/ DOWN▼button to go to the
BATTERY TYPE page.
2 Press and hold SET button for 2 seconds,
then the cursorwill flash to allow
changes to be made.
3 Press UP▲/ DOWN▼button to select
either NiMH (rechargeable battery) or
AKLN (alkaline battery).
4 After selecting the battery type, press and
hold the SET button for 2 seconds or wait 9
seconds to save the setting.
IMPORTANT: NiMH battery must be selected when rechargeable battery is being used. Never
select AKLN (alkaline) when transmitter is intended for charging as alkaline battery isn’t
rechargeable. Wrong battery selection will result in battery sensing electronics to display wrong
and misleading status information.
SET
SET
SET
SET
SET
SET
SET
SET
SM-5016 UHF Belt-pack Transmitter
GAIN setting
Gain control enables the user to set different output levels.
GT (LEFT) is for the use of instrument with
high impedance, such as guitar.
MT (RIGHT)is for the use of low impedance
such as lapel or headset microphones
GT MT
GT MT
CHIAYO ELECTRONICS CO.,LTD.
Http://www.chiayo.com.tw｜Email: sales@chiayo.com.tw
Office: 30, Lane 27, Section 4, Jen-Ai Road, Taipei 10685, Taiwan
Tel: 886-2-27415741｜Fax: 886-2-27525242
Factory: 88, Chung-Hsiao Street 2, Chiayi 60080, Taiwan
Tel: 886-5-2711000｜Fax: 886-5-5767611
Otros manuales de Transmisor de Chiayo
Chiayo
Chiayo SM-6100 IrDA Manual de usuario
Chiayo
Chiayo NB-3100 Manual de usuario
Chiayo
Chiayo SM-6100 IrDA Manual de usuario
Chiayo
Chiayo SM-6100 IrDA Manual de usuario
Chiayo
Chiayo SM-2100 IrDA Manual de usuario
Chiayo
Chiayo SM-6000 Manual de usuario
Chiayo
Chiayo SM-9000 IrDA Manual de usuario
Chiayo
Chiayo DB-2400 Manual de usuario
Chiayo
Chiayo SM-7100 IrDA Manual de usuario
Manuales populares de Transmisor de otras marcas
Dejero
Dejero EnGo 3x Manual de usuario
Rosemount
Rosemount 4600 Manual de usuario
Speaka Professional
Speaka Professional 2342740 Manual de usuario
trubomat
trubomat GAB 1000 Manual de usuario
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manual de usuario
Rondish
Rondish UT-11 Manual de usuario
