Chesney's EFB1200 Manual de usuario
1
Configuration of EFB1200 with Wi-Fi and
Smart Home System manual
CHESNEY’S
Issue 01
2
1. CONFIGURATION WITH WIFI AND SMARTPHONE
For a configured appliance the following functions are available:
-Turn on the appliance (if READY message is on display).
-Turn off the appliance (if COOLINGTHE DEVICE or READY message is on display)
- Increase or lower the flame height of the appliance during use.
-Turn on/off the ‘LOCK THE DEVICE’ function (Customer’s Menu, point 1).
- Select the appliance if more than one appliance has been installed.
To configure the appliance with Wi-Fi:
Ensure that the Wi-Fi network is of 802.11 b/g/n standard and it operates the
encryption of WPA/WPA2 PSK.
If the Wi-Fi network does not fulfil the above mentioned requirements it will have
to be adjusted in order for configuration to take place.
If Wi-Fi network is ready, prepare the formatted USB flash drive.
Create a text file on a USB flash drive with the name ‘wifi’
and ‘txt’ extension.
Save the name of the network and password in the file in the following format:
3
Instead of ‘Wi-Fi Network Name’ - enter the name of the network, e.g. ‘home’.
Wi-Fi Network Password - password to the network, e.g. ‘mynet’.
Example:
Make sure that the appliance is disconnected from the mains then insert the USB
flash drive to USB port on the side part of the product.
USB PORT
Connect the appliance to the mains and wait a minimum of 5 minutes.
The USB flash drive may be disconnected and the product may be turned on with
the button.
Hold ‘+’ for 8 seconds and ‘Customer’s menu’ will appear [p.10 in the User’s
manual]. Press ‘+’ to go to point 4 ‘Device IP’ and confirm by pressing ‘-’.
The products IP needed for the operation via the configured appliance will be
visible then.The correct IP format is: 192.168.XXX.XXX
4
The assigned IP address is a dynamic address and is subject to change in the
event of a change in the network settings.
It may happen that the displayed IP is incorrect. In such a case follow the
instructions below:
0.0.0.1 No communication with
the module at all
It is normal during the initialization of the
product. If it does not disappear after
several minutes after turning on the
appliance, begin to format the USB flash
drive again.
0.0.0.2* No connection with the
network (wrong data / IP
is busy / no network)
Follow the procedure of giving the network
parameters once more - install the USB
flash drive again.
0.0.0.3 Text mode - jumper was
not downloaded
Follow the procedure of giving the network
parameters once more - install the USB
flash drive again. Call SERVICE
127.0.0.1 No connection with the
network (wrong data / IP
is busy / no network)
Follow the procedure of giving the network
parameters once more - install the USB
flash drive again.
* In case of problems connecting to the fireplace via user’s WiFi network (error
no. 0.0.0.2) due to low network signal:
- remove the seal located in the front of the appliance indicated with a sticker
5
- cut the band that is clipping the cable
- take out the cable with the WiFi transceiver at its end
- repeat the connection procedure
NOTE:
The cause of failure to configure can be ascertained by reading the file ‘wifi.txt’.
Network parameters changed The change of all the network
parameters was successful
Error 0x01 Interfaces error (call service)
Data changed successfully The change of network password
network name was successful
Incorrect data format Data incorrectly entered into the file
(save data again on the USB flash drive,
if it does not work, format the USB flash
drive or use a different one)
If the displayed IP number is the correct one, save it.
The mobile appliance should be connected to the configured Wi-Fi network.The
operation of the appliance via the website has been tested with the following
browsers:
Windows: Opera, Firefox, Chrome, IE min11
Android: Firefox, Chrome, Opera Browser, Opera Classic, Safari
Apple: Safari, Chrome
In the address bar enter the saved IP address and download the webpage.
6
The display will appear on the device:
Appliances can be individually
named so that specific appliances
can be selected where more than
one has been installed.
Activates ‘LOCK THE DEVICE’ function (see: User’s Manual, III. Customer’s Menu, 1.)
7
Using the SETTINGS function it is possible to determine:
- Serial number
- Display and microprocessor’s program version
- Total time of appliance operation
- Website version
8
Using MANAGER function it is possible to control an unlimited number of configured
appliances.
NOTE:
In order to successfully operate the appliance it is essential that the user is familiar
with the User’s manual and that the appliance has been installed in accordance with
the instructions contained in the Installation manual.
9
2. SMART HOME SYSTEM CONNECTION
When the Smart Home System driver is installed, it can be used to:
-Turn on the appliance (if READY message is on display).
-Turn off the appliance (if COOLINGTHE DEVICE or READY message is on display)
- Increase or lower the flame height of the appliance during use.
The following appliance modes can be seen the Smart Home System control panel:
- ready to start (message READY)
- working (message WORKING)
- lack of fuel (message NO FUEL)
- waiting (message WAITING or COOLING THE DEVICE)
- ERROR
Description of Smart Home System ports:
INPUT 12-24 VDC ABCD
INFORMATION
CONTROL
GDN COM DC-V START STOP UP DOWN
Description of electrical connectors:
GND - COM DC -V
START - 12 DC +V input initializing the appliance, signal as an impulse lasting 100ms up to 1s.
STOP - 12 DC+V input turning off the appliance, signal as an impulse lasting 100ms up to 1s.
UP - 12 DC +V input increasing the flame, signal as an impulse lasting 100ms up to 1s.
DOWN - 12 DC+V input decreasing the flame, signal as an impulse lasting 100ms up to 1s.
A-READY - transmitter output signalling that the appliance is ready.
B-WORKING - transmitter output signalling that the appliance is working.
C-FUEL - transmitter output signalling lack of fuel.
C-FUEL - transmitter output signalling error/other.
A+B - transmitter output.
10
All the ports have been adjusted to work within direct current voltage of 12V-24V.
Higher voltage requires the use of an additional limiter installed on the module’s port.
More than one appliance can be controlled simultaneously. In order to do so, it is
essential to divide the signal, using one for each appliance.
Description:
Input - voltage port 12V-24V of the direct current.
Output - voltage port 12V-24V of the direct current depending on the mode of the
appliance.
The following chart shows mode ports where signals will appear depending on the
mode of the appliance. See illustration on p.6 for alphabetically referenced ports.
1 - port with signal
0 - port without signal
MODE A B C D
READY 1 0 0 0
WORKING 0 1 0 0
FUEL 0 0 1 0
ERROR 0 0 0 1
WAIT/COOLING 1 1 0 0
Otros manuales para EFB1200
1
Otros manuales de Chimenea de interior de Chesney's
Chesney's
Chesney's Marble Manual de usuario
Chesney's
Chesney's EFB1200 Manual de instrucciones
Chesney's
Chesney's EFB22 Manual de instrucciones
Chesney's
Chesney's CUBB18 Alchemy Instrucciones de funcionamiento
Chesney's
Chesney's CUBB18 Alchemy Instrucciones de funcionamiento
Chesney's
Chesney's Alchemy GFL850URN Instrucciones de funcionamiento
Chesney's
Chesney's The Bronze Urn Manual de instrucciones
Chesney's
Chesney's Alchemy FB18 Manual de instrucciones
Chesney's
Chesney's CUBB18 Alchemy Instrucciones de funcionamiento
