CHERUBINI RX Mini Manual de usuario
A510036
ISTRUZIONI - INSTRUCTIONS - EINSTELLANLEITUNGEN
INSTRUCTIONS - INSTRUCCIONES
I
GB
D
F
E
CENTRALINA PER TENDE DA SOLE
E AVVOLGIBILI CON RICEVITORE RADIO
RADIO RECEIVER FOR
ROLLING SHUTTERS AND AWNINGS
FUNKEMPFÄNGER FÜR
ROLLLÄDEN UND MARKISEN
RÉCEPTEUR RADIO POUR
VOLETS ROULANTS ET STORES
CUADRO DE MANIOBRAS PARA PERSIANAS Y
TOLDOS CON RECEPTOR RADIO INCORPORADO
RX MINI
20
ENGLISH
Table of contents:
Safety instructions .................................................................................................. p. 21
Electrical connections Mini RX Ref. A510036 ......................................................... p. 21
Key to symbols ....................................................................................................... p. 22
Technical features .................................................................................................. p. 22
Command sequences example ............................................................................... p. 23
Function open/close programming remote control ............................................. p. 24-25
Setting the rst remote control (Skipper or Giro Series) ......................................... p. 26
Automatic disabling of the rst remote control setting function ............................ p. 26
Setting the rotation direction of the motor ............................................................. p. 26
Setting of additional remote controls (Skipper or Giro Series) ................................ p. 27
Programming the A530058 remote control with 4 independent channels.............. p. 27
Remote control memory clearing ........................................................................... p. 28
Full memory clearing .............................................................................................. p. 28
Activation by remote control .................................................................................. p. 29
Optional wired switch ............................................................................................ p. 30
Change mode from DM to MC and vice versa ................................................... p. 30-31
Operation with sun/wind sensor ............................................................................. p. 32
Compatible devices
Mistral sensor ......................................................................................................... p. 33
Rugiada .................................................................................................................. p. 34
Anemometers ......................................................................................................... p. 34
Enable/disable the sun sensor ................................................................................ p. 35
Test mode for WindTec/WindTec Lux ....................................................................... p. 35
Special functions: short-term setting of a remote control .................................... p. 36
EU Declaration of conformity ................................................................................. p. 36
N L
LN
230 V 50 Hz
6
2
1
3
2
13
3
1
2
5
4
6
SAFETY INSTRUCTIONS
ELECTRICAL CONNECTIONS
MINI RX Ref. A510036
• Only professional technicians must perform installation, complying with all safety
instructions, especially those regarding electrical connections.
• To avoid short circuits, arrange an automatic bipolar switch with opening distance of the
contacts of at least 3 mm before the circuit.
• If not used, the white wire must be insulated. It is dangerous to touch the white wire
when the motor is powered.
SKIPPER Series
Commutator
Common
Down
Up
Button
1 BROWN - PHASE
2 BLUE - NEUTRAL
3 WHITE - OPTIONAL
WIRED SWITCH
4 GREEN - DOWN
OUTPUT
5 YELLOW - UP OUTPUT
6 RED - COMMON
Connection for optional wired switch
21
ENGLISH
GIRO Series
A530058 Remote Control
with 4 independent
channels
KEY TO SYMBOLS
TECHNICAL FEATURES
- Power supply 230 V / 50 Hz
- Power consumption 0,5 W
- Radio Frequency 433,92 MHz
- Decoder System Rolling Code
- Modulation AM/ASK
- Max. number storable transmitters 15
- Max. motor power 300 W
- Operating temperature -10 C° +55 C°
- Dimensions 40x40x20 mm
- Weight 80 gr
- Protection degree IP44
ENGLISH
22
Disconnect the
power supply
Power up
A530058 Remote Control
with 4 independent
channels
GIRO
down
stop
up
A
B
C
Skipper
A
B
C
Button or
commutator, wired
Press button A
A
Press buttons A and B
at the same time
+
A B
Press button SET
SET
Led Awning
down
up
short motor
rotation in one
direction
long motor
rotation in the
other direction
double short
rotation
UP
DOWN
STOP
GIRO
COMMAND SEQUENCES EXAMPLE
Most of the command sequences have three distinct steps, at the end of which the motor
indicates if the step has been concluded positively or not, by turning in different ways.This
section is provided to demonstrate the motor indications. The buttons must be pressed as
shown in the sequence, without taking more than 4 seconds between one step and the
next. If more than 4 seconds are taken, the command is not accepted and the sequence
must be repeated.
Command sequence example:
As we can see from the example, when the sequence ends positively, the motor returns to
its starting position in one long rotation. In fact, two short rotations in the same direction
correspond to one long rotation in the opposite direction.The motor returns to the starting
position even when the sequence is not completed; in this case by performing one or two
short rotations.
Example of a wrong sequence:
Step 1
Step 1
Step 1
> 4 sec repeat the
sequence
repeat the
sequence
Step 3Step 2
23
ENGLISH
+
A B B B
> 4 sec
+
A B
+
A B B
ENGLISH
24
FUNCTION OPEN/CLOSE PROGRAMMING
REMOTE CONTROL SKIPPER PLUS - SKIPPER LUX - SKIPPER P-LUX
To prevent accidental changes to the programming of the motor during the daily use of
the remote control, the possibility of programming is disabled automatically 8 hours after
sending the last sequence (A+B or B+C).
CHECKING THE STATUS OF THE FUNCTION
To change the status of the function, see the sequences “ENABLE/DISABLE
PROGRAMMING”
Proceed with programming as the instructions booklet
ENABLE PROGRAMMING
DISABLE PROGRAMMING
C
Open
or after
30 sec.
Remove and replace a battery
OPTION 2
OPTION 1
+ +B C
Tn
B
+ +
BC
Tn or after
30 sec.
B
Open
programming
Closed
programming
3 sec
+ +
A
A
A
BC
Tn or after
30 sec.
B
A
3 sec
Closed
3 sec
25
ENGLISH
FUNCTION OPEN/CLOSE PROGRAMMING
REMOTE CONTROL SKIPPER - SERIES GIRO
To prevent accidental changes to the programming of the motor during the daily use of
the remote control, the possibility of programming is disabled automatically 8 hours after
sending the last sequence (A+B or B+C).
CHECKING THE STATUS OF THE FUNCTION
To change the status of the function, see the sequences “ENABLE/DISABLE
PROGRAMMING”
Proceed with programming as the instructions booklet
ENABLE PROGRAMMING
DISABLE PROGRAMMING
ON
Open
programming
Closed
programming
....
ON
....
.... Closed
Open
ON
or after
30 sec.
or after
30 sec.
1 2 3
OPTION 1
1 2 3
1 2 3 or after
30 sec.
+ +
A B CB
B
C
+ +
A B C
+ +
A B C
A
B
Tn
Tn
Tn
OPTION 2 OPTION 2
OPTION 2 OPTION 2
Remove a battery
and wait 5 seconds,
or press any button.
2 sec
B
SETTING THE FIRST REMOTE CONTROL (Skipper or Giro Series)
SETTING THE ROTATION DIRECTION OF THE MOTOR
This operation can only be performed when the control unit is new, or after a total delete
of the memory.
During this step, power up only one control unit at time!
T1: First remote control to be set
This operation is mandatory if the rotation direction of the motor does not match to the
UP and DOWN functions of the remote control as an exemple if giving UP command the
awning or blinds descend.
The proper motor direction must be set, if the motor is linked to a Wind sensor. In case of
a wind alarm, the motor will always perform the command associated to the UP button.
Setting the rotation direction using the SET button:
Interchanging the BROWN and BLACK motor wire on the terminals of the control unit,
will also reverse the rotation direction.
The control unit will keep this setting even after complete memory clearing.
max. 2 sec
26
ENGLISH
Every time you connect the power supply to the control unit, you have 3 hours to
store the rst remote control. After this time, the ability to store the remote control is
disabled. To reset the timer of the function you have to disconnect and reconnect the
power supply to the control unit.
AUTOMATIC DISABLING OF THE FIRST
REMOTE CONTROL SETTING FUNCTION
T1 T1 T1 (2 sec)
+
A B B B
SETTING OF ADDITIONAL REMOTE CONTROLS
(Skipper or Giro Series)
SETTING THE A530058 REMOTE CONTROL
WITH 4 INDEPENDENT CHANNELS
Up to 15 remote controls can be set, including the light/wind sensor.
Tn: Already programmed remote control
Tx: Additional remote control
The A530058 remote control must be set from another Skipper or Giro Series remote
control that has already been programmed.
• Press the A and B buttons at the same time.
• The motor makes a short movement.
• Then press the B and C buttons at the same time.
• The motor makes a short movement again.
• Then, press the desired button on the A530058 remote control for at least 2 seconds.
• The motor makes a long movement.
Tn: Already programmed remote control
Tx: Additional remote control
27
ENGLISH
TnTn Tx (2 sec)
+
A B BB
+
AB+ CB
1
3 4
2
Tx (2 sec)Tn Tn
+
A B
+
B C
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
