Checkpoint ATP Series Hoja de especificaciones

QUICK SETUP

Series ATP

www.cppumps.com

Tool Requirements

Hex Wrenches: 1/8”, 5/32”, 3/16”

Open-End Wrenches: 7/16”, 5/8”, 7/8”, 1”

Leg Assembly and Pump Attachment

1. Unpack pump stand assembly, and ensure that all pieces are

supplied.

2. Place pump bracket (ATP0090-01) onto both legs. The four holes

near the edge of the bracket are located between the two legs (as

shown below).

3. Install the two rear bolts with washers through the pump bracket and

legs of the pump stand, and tighten the hex nuts.

PART #

DESCRIPTION

QTY.

ATP0090-01

PUMP BRACKET

HHBS8042028

HEXHEAD BOLT

HHNIS80420

HEX NUT

HWSHS804

FLAT WASHER

PST0002-1

LEG –SOLAR

WARNING: Ensure that you are wearing proper PPE before performing any action.

WARNING: Pinch points. Disconnect power before removing cover.

4. Remove the front cover from the pump drive.

5. Set the pump on the stand such that the four carriage-assembly bolt-

heads line up in the stand clearance holes. Install the two front bolts

with washers from the underside of the pump through the legs and

into the pump drive housing, and tighten hex nuts.

6. Connect the suction line to the bottom check valve, and connect the

discharge line to the top check valve.

CP-QS-ATP

REV00 EFF. DATE: 1/9/2019

Page 1 of 2

QUICK SETUP

Series ATP

www.cppumps.com

Chemical Flow Rate Adjustment

7. Loosen the lock screw on the adjustment block. Using the supplied adjustment tool, turn the adjustment nut to increase or

decrease the flow rate to the desired percentage, as indicated by the markings (refer to the flow charts to estimate position

based on your application).

CAUTION: Do not turn the adjustment nut to apply force below the 0% or above the 100% mark.

8. Re-tighten the lock screw on the adjustment block.

9. Reinstall the pump cover.

10. Connect the pump to the electrical service.

CAUTION: Ensure that the power source does not exceed the rating for the pump motor.

11. With fluid media present at the pump suction, loosen the bleed screw and discharge line at the discharge check outlet to

vent to atmosphere. Run the pump until all air trapped in the head is released. Stop the pump.

Re-tighten the discharge line and bleed screw.

12. Run a drawdown flow calibration. If the flow rate is correct, stop here. If the flow rate requires adjustment, continue.

13. Disconnect the power.

WARNING: Pinch points. Disconnect power before removing cover.

14. Remove the pump cover.

15. Return to Step 7. Repeat these steps until the target flow rate is achieved.

CP-QS-ATP

REV00 EFF. DATE: 1/9/2019

Page 2 of 2

Otros manuales para ATP Series

Tabla de contenidos

Otros manuales de Bomba de agua de Checkpoint

Checkpoint

Checkpoint 1250 Series Manual de usuario

Checkpoint

Checkpoint 6200 Series Manual de usuario

Checkpoint

Checkpoint ATP3 Series Manual de usuario

Checkpoint

Checkpoint 5400 Series Manual de usuario

Checkpoint

Checkpoint ATP Series Manual de usuario

Checkpoint

Checkpoint SLA Series Manual de usuario

Checkpoint

Checkpoint GX15G11C3 Series Manual de usuario

Checkpoint

Checkpoint 1250E Series Manual de usuario

Checkpoint

Checkpoint SLA Series Hoja de especificaciones

Manuales populares de Bomba de agua de otras marcas

Neptun

Neptun NPHW 5500 Manual de usuario

Sensidyne

Sensidyne Gilian BDX-II Instrucciones de instalación y funcionamiento

Draper

Draper 47808 Manual de usuario

Trolla

Trolla 12820 Manual de usuario

Sunfab

Sunfab SVH Series Manual de usuario

WilTec

WilTec 50740 Manual de usuario

Fieldmann

Fieldmann FVC 5015 EK Manual de usuario

Everbilt

Everbilt EFSUB5-122HD Manual de usuario

Graco

Graco Husky 3300e Manual de usuario

esotec

esotec 101018 Manual de usuario

moyno

moyno 2000 CC Manual de usuario

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manual de usuario

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guía de solución de problemas

DUROMAX

DUROMAX XP WX Series Manual de usuario

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manual de usuario

Franklin Electric

Franklin Electric IPS Manual de usuario

Xylem

Xylem e-1532 Series Manual de usuario

Milton Roy

Milton Roy PRIMEROYAL Manual de usuario