CHC I80 GNSS Manual de usuario

CHC® i80 GNSS Receiver

QuickTour with FieldGenius

(Internal GSM Rover Mode)

i80 GNSS Receiver Quick Tour with FieldGenius (Internal GSM Rover)

1

1.Prerequisites

Hardware: CHC i80 rover , Controller Kit, SIM

card ,Lithium Battery, Pole

Software: FieldGenius8

2.Steps to set i80 working as

rover in internal GSM mode with

FieldGenius

2.1 Rover installation

Insert the SIM card to i80, screw the rover

receiver on the pole, and put the Controller

adapter in the right place like the figure.

Note: The recommend firmware version of

i80 is 1.3.36 or higher. If not, please contact

local dealer or CHC Support for latest

firmware.

2.2 Rover setting in FieldGenius

1. Power on the receiver

Long press the i80 power button until the

green and blue LED lights are on.

2. Click on [start] and then FieldGenius.

3. Click [New Project] to create a project or

Click [Open] to open one exist project.

i80 GNSS Receiver Quick Tour with FieldGenius (Internal GSM Rover)

2

4. A project file should be selected then

click [Continue] for next step

5. Click on [Select Instrument]

6. Select [GNSS Rover] option then click

[Edit] to select device and linking method

7. Click [Antenna Height] tab to set the

antenna height of the receiver

i80 GNSS Receiver Quick Tour with FieldGenius (Internal GSM Rover)

3

9. Click [Model and Communication]

tab→select Make as [CHC], Model as [i80],

Port as [Bluetooth] →click [Bluetooth Device

List] to add bluetooth device

10. Click [Search] to search the around

Bluetooth device.

i80 GNSS Receiver Quick Tour with FieldGenius (Internal GSM Rover)

4

11. Click on the device that matches your

device serial number, then click it

12. Type in the PIN Code of the bluetooth

then click [OK] button to finish the device

edit.

13. Then our target device can be selected in

the bluetooth device list. Click [OK] button

back to [Model and Communication]

interface.

14. The target device can be selected in the

drop-down box then click [Connect] button.

The software will build the connection to your

device

i80 GNSS Receiver Quick Tour with FieldGenius (Internal GSM Rover)

5

14. Select the Link Device as [GSM Module]

from the drop-down box, select the Data

Format as [Auto Detect] then click the [Setup]

button.

15. Please type in the APN info in the

Network Options according to the SIM

card,then select the Source Type as NTRIP.

Click [Press to modify] button to create a

NTRIP account information.

16. Please click the [Add] button

Type in your CORS information in the blank.

Then click the [Ok] button

i80 GNSS Receiver Quick Tour with FieldGenius (Internal GSM Rover)

6

After that the new CORS can be selected in

the list, please select the CORS you want to

use then click [Select]

Then click [Ok] button to finish setting

17. Click [Connect] to finish starting rover

18. Then the green LED will flash and the

states will become [Autonomous] to [float]

then to [fix],which means the rover is getting

the correction data from base.

19. The survey work can be done with the

i80

Otros manuales para i80 GNSS

13

Tabla de contenidos

Manuales populares de Receptor de otras marcas

Garmin

Garmin GA 23 Manual de usuario

Aiphone

Aiphone PS-12F Manual de usuario

IMES

IMES TCS-01CA-PMI Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR Manual

AMIMON

AMIMON AMN12310 WHDI Manual de usuario

Dual

Dual DMCPA79BT Instrucciones de funcionamiento

Sound Associates

Sound Associates SA652P Manual de usuario

Sherwood

Sherwood NewCastle R-772 Manual de usuario

Audio

Audio A10-RX Series Manual de usuario

AllSee

AllSee PushShare PSRV1.1 Manual de usuario

DEMAG

DEMAG DRC-DR D2 Manual de usuario

Teleco

Teleco TVRCL868A02 Manual de usuario

Bosch

Bosch RF3222E Manual de usuario

Kramer

Kramer 631R Manual de usuario

Xpress

Xpress xmc10 Manual de usuario

JVC

JVC KD-MR1BTS Manual de usuario

Omega Engineering

Omega Engineering UWTC-REC3 Manual de usuario

e-survey

e-survey E300 Pro Manual de usuario