Chauvin Arnoux C.A 6423 Manual de usuario

■■

■CONTRÔLEURDETERRE

■■

■EARTHTESTER

■■

■ERDUNGSPRÜFER

■■

■STRUMENTODI CONTROLLO DELLA TERRA

■■

■CONTROLADORDETIERRA

C.A 6423

北京海洋兴业科技股份有限公司（证券代码：839145）

电话：010-62176775

网址：www.hyxyyq.com

English

WARRANTY

Unless notified to the contrary, our instruments are guaranteed from any manufacturing

defect or material defect. They do not bear the specification known as the safety specification.

Our guarantee, which may not under any circumstances exceed the amount of the invoiced

price, goes no further than the repair of our faulty equipment, carriage paid to our workshops.

It is applicable for normal use of our instruments, and does not apply to damage or destruction

caused, notably by error in mounting, mechanical accident, faulty maintenance, defective

use, overload or excess voltage.

Our responsability being strictly limited to the pure and simple replacement of the faulty parts

of our equipment, the buyer expressly renounces any attempt to find us responsible for

damages or losses caused directly or indirectly.

Our guarantee is applicable for twelve (12) months after the date on which the

equipment is made available. The repair, modification or replacement of a part during the

guarantee period will not result in this guarantee being extended.

SAFETY IN USE

■Before connecting up the C.A 6423, check that no dangerous voltage is present at the

earth to be measured.

■Before opening the battery compartment, ensure that no measurement lead is connected

to the instrument.

Meaning of symbol: Warning!

Consult the User’s manual before using the instrument.

You have just acquired an Earth Tester and we thank you for your confidence.

To get the best service from your instrument:

-read carefully this user’s manual,

-respect the safety precautions in it,

-stick the label corresponding to your language on the back of the instrument.

北京海洋兴业科技股份有限公司（证券代码：839145）

电话：010-62176775

网址：www.hyxyyq.com

SUMMARY

Page

1. PRESENTATION ...................................................................................................................................................... 15

2. DESCRIPTION ........................................................................................................................................................... 16

3. OPERATINGMODE .............................................................................................................................................. 17

3.1. Measurement of resistance of an earth point .................................................................. 17

3.2. Measurement of resistance ........................................................................................................... 18

3.3. Fault signals .............................................................................................................................................. 19

4. SPECIFICATIONS ................................................................................................................................................... 20

5. MAINTENANCE ......................................................................................................................................................... 23

5.1. Normal cleaning ..................................................................................................................................... 23

5.2. Calibration check ................................................................................................................................... 24

5.3. Repair ............................................................................................................................................................ 24

6. TOORDER .................................................................................................................................................................... 25

1. PRESENTATION

Autonomous and watertight, this tester is a worksite instrument designed for earth resistance

measurements. It is particularly suited to measurements in difficult conditions such as when

there are stray voltages present, high telluric currents, high value auxiliary electrode

resistances, etc...

For ease of use, this instrument has the following features:

■a single press button to trigger the measurement

■an autoranging system for measurement range switching

■a large digital display which is readable even in shadow

■

three indicators that signal the presence of faults which can lead to errors during measurement

■three colour coded screw terminals to simplify connection of leads

■an attached connection rod

北京海洋兴业科技股份有限公司（证券代码：839145）

电话：010-62176775

网址：www.hyxyyq.com

2. DESCRIPTION

1Measurement input terminal E (green)

2Measurement input terminal S (blue)

3Measurement input terminal H (red)

4Attached rod S - H for 2 wire resistance measurement

52000 count digital LCD

6Low battery indicator

7Reverse connection indicator

8Current circuit fault indicator (E - H)

9Voltage circuit fault indicator (E - S)

10 Indicator of presence of interference on voltage circuit (E - S)

11 Measurement press button

10 7

1432

北京海洋兴业科技股份有限公司（证券代码：839145）

电话：010-62176775

网址：www.hyxyyq.com

3.1 MEASUREMENT OF THE RESISTANCE OF AN EARTH POINT

To measure the resistance of an earth conductor, the so-called "62% method" is in general

recommended. This measurement requires the use of the items in the Earth Kit (see Ch.6:

TO ORDER).

Cut the power supply to the installation and disconnect it from the earth by

opening the earth bar!

1. Connect terminal E to the earth to be measured.

2. Check that the bar 4is not present between terminals S and H.

3. Drive in (completely if possible) the input earth rod H at a distance "a" from the earth point

(E) to be measured.

Note:

this distance is further for a deep and extended earth point (larger range of influence).

4. Drive in the rod S at 62% of the distance between the earth E and the rod H (the rods S,

H and the earth point must be in line).

5. Connect the rods to their respective terminals with the leads.

6. Press the "MEASURE" button 11 and hold the button during measurement. Check that

none of the three indicators are flashing, otherwise, check the wiring (see Ch.3.4: FAULT

SIGNALS) and make the measurement again.

Measurement of resistance of earth point

3. OPERATING MODE

E S H

earth bar

S'' S' H

earth

point

0 % 52 % 62 % 72 % 100 %

北京海洋兴业科技股份有限公司（证券代码：839145）

电话：010-62176775

网址：www.hyxyyq.com

Checking the measurement

7. Note the displayed value.

8. Wait for a few moments and then re-measure.

9. Move rod S by 10% towards H, along the line between the earth point E and the rod H.

Measure and note the result.

10. From its initial position, move rod S by 10% towards E, along the line between the earth

point E and the rod H.

If the three values are of the same order of magnitude, the earth measurement is correct. If

not, increase the distance "a" and repeat the measurements.

Do not forget to reconnect the earth point after the measurement.

3.2 MEASUREMENT OF RESISTANCE

This measurement can be performed to determine the coupling resistance between two earth

points. For example, between the neutral and ground earth points (EDF distribution).

Cut the power supply of the installations. For measurement of the coupling

resistance, disconnect the earths!

1. Short-circuit terminals S and H using the bar provided 4.

2. Connect terminal E to the earth of the ground, and terminal H to the earth of the neutral.

3. Press the "MEASURE" button 11 and hold down until the measurement is displayed.

Check that none of the three indicators are flashing, otherwise check the connections (see

Ch.3.4: FAULT SIGNALS) and repeat the measurements.

2-wire resistance measurement

E S H

earth

bar

earth

bar

earth 1 earth 2

北京海洋兴业科技股份有限公司（证券代码：839145）

电话：010-62176775

网址：www.hyxyyq.com

NB: In the case of low value resistances, it becomes necessary to take into account the

resistance of the leads (approx. 22.5 mΩ/m for those supplied as accessories). To overcome

the resistance of the leads, we advise the use of a (4 pole) Earth/Resistivity Tester, on 4-wire

connection.

Do not forget to reconnect the earth points after measurement.

3.3 FAULT SIGNALS

■Display of a negative measurement

Reversal of rods H and E or rods S and E

Re-connect the leads correctly

■Displayed measurement value is 1---

Overrange (R > 2000 Ω)

Check the connections

■Flashing of FAULT light 8

Fault in current circuit (E - H). Flashing indicates that the voltage between the terminals E and

H is greater than 30 Vpeak.

This may mean that:

- the resistance of the current circuit between E and H is too high,

- the interference voltage in the circuit (E - H) is too high,

- the fuse is blown.

Check the rods, the leads, the connections and the fuse (see Ch.5.1.3).

■Flashing of HIGH RESISTANCE indicator 9

Fault in the voltage circuit (E - S). At the start of the measurement, the instrument

automatically checks the resistance between E and S. If this is greater than 50 kΩ, the

indicator 9begins to flash. This means that the measurement is likely to be very affected by

the resistance of the voltage circuit.

NB: The indicator flashes throughout the measurement, even if the resistance falls below

50 kΩduring it.

Check the rods, the leads and their connections.

■Flashing of HIGH NOISE indicator 10

Presence of interference voltages in the voltage circuit. Flashing indicates noise greater than

13 Vpeak between terminals E and S. These interference signals disturb the measurement.

Move the rods.

北京海洋兴业科技股份有限公司（证券代码：839145）

电话：010-62176775

网址：www.hyxyyq.com

4. SPECIFICATIONS

REFERENCE CONDITIONS

Temperature 23°C ± 3 K

Relative humidity 45% < RH < 55%

Supply voltage 10.5 V ± 0.2 V

Auxiliary resistances RH, RS and REnil

AC and DC interference voltages nil

Electric field < 1 V/m

Magnetic field < 40 A/m

DISTORTION QUANTITIES

Operating limits Max variation

Temperature -10...+55°C ± (1% rdg ± 1 pt) per 10°C

Relative humidity 20...90% ± 2% rdg ± 5 pt

Operating voltage 8.8...12.5 V ± (1% rdg ± 1 pt) per Volt

Voltage circuit load (1) 50 kΩ± 1% rdg per 10 kΩ± 4 pt

Current circuit load (2) 0.00...19.99 Ω 30 kΩ± 1% rdg per 10 kΩ± 2 pt

20.00...199.9 Ω30 kΩ±1% rdg per 10 kΩ± 2 pt

200.0...1999 Ω50 kΩ±1% rdg per 10 kΩ±2 pt

DC voltage 0...20 V (3) negligeable

AC interference voltages on H 0...23 Vrms or 32 Vpeak ±2% rdg ± 2 pt

AC interference voltages on S 0...9 Vrms or 13 Vpeak ±0.5% rdg ± 2 pt

(1) Resistance measured or resistance of rod E + resistance of rod S + resistance of leads

(2) Resistance measured or resistance of rod E + resistance of rod H + resistance of leads

(3) Possible flashing of HIGH RESISTANCE indicator above 4.5 V

METROLOGICALSPECIFICATIONS

Measurement range Resolution Measurement current Accuracy Empty voltage

(automatic range) (square signal 128 Hz)

0.00...19.99 Ω 0.01 Ω10 mA ± 2%rdg ±1 pt ≤42 Vpeak

20.00...199.9 Ω 0.1 Ω1 mA ± 2%rdg ±1 pt ≤42 Vpeak

200.0...1999 Ω 1 Ω100 µA ± 2%rdg ±3 pt ≤42 Vpeak

Response time between 4 and 8 s depending on measurement conditions

北京海洋兴业科技股份有限公司（证券代码：839145）

电话：010-62176775

网址：www.hyxyyq.com

ELECTRICALSPECIFICATIONS

Power supply 8 batteries R6 alkaline 1.5 V or 8 accumulators

Range of voltage permitted 8.8...12.5 V

Average battery life 1800 measurements of 15 seconds (at 23°C ± 3 K, with 8

alkaline batteries) permanent test of remaining battery life.

DISPLAY

Display LCD, 7 segments, height 18 mm,

2000 counts (3½ digits), direct reading in Ω

Low battery indicator "LO BAT" message

Overload indicator displayof 1 ---

Indicator of lead reversal - sign preceding the measurement

Indicator of current circuit fault by flashing red FAULT (E -H) LED

Indicator of voltage circuit fault

■Resistance too high by flashing red HIGH RESISTANCE (E - S) LED

■Interference noise by flashing red HIGH NOISE (E - S) LED

MECHANICAL SPECIFICATIONS

Protection index IP 54 in accordance with IEC 529 and NF EN 60529

Free drop 25 cm in accordance with IEC 68-2-32

Shock resistance 50 gn(gn= 9.81 m/s²) in accordance with IEC 68.2.27

Resistance to impacts IK 04 in accordance with NF EN 50102

Vibration resistance ± 1 mm, from 10 to 55 Hz in accordance with IEC 68.2.6

Dimensions (W x H x D) 238 x 136 x 150 mm

Connection of leads on 3 colour coded terminals for φ4 mm banana plugs or

6 mm spade clips

北京海洋兴业科技股份有限公司（证券代码：839145）

电话：010-62176775

网址：www.hyxyyq.com

CLIMATIC CONDITIONS

Domaine nominal de référence

Domaine d'utilisation

Domaine de stockage

100

Humidité en % HR

- 40 - 20 0 20 40 60 80

Température

en °C

Humidity in % RH

Nominal reference range

Operating range

Storage range

Temperature

in °C

CONFORMITY WITH STANDARDS

Electrical safety (in accordance with IEC 61010-1)

-Double insulation

-Installation category III

-Degree of pollution 2

-Service voltage 42 Vpeak

Electromagnetic compatibility

■Emissions and immunity in an industrial setting compliant with IEC 61326-1.

北京海洋兴业科技股份有限公司（证券代码：839145）

电话：010-62176775

网址：www.hyxyyq.com

Otros manuales para C.A 6423

Tabla de contenidos

Otros manuales de Equipo de prueba de Chauvin Arnoux

Chauvin Arnoux

Chauvin Arnoux C.A 6630 Manual de usuario

Chauvin Arnoux

Chauvin Arnoux 10141 Manual de usuario

Chauvin Arnoux

Chauvin Arnoux C.A 6131 Manual de usuario

Chauvin Arnoux

Chauvin Arnoux C.A 755 Manual de usuario

Chauvin Arnoux

Chauvin Arnoux C.A 6608 Manual de usuario

Chauvin Arnoux

Chauvin Arnoux C.A 6131 Manual de usuario

Chauvin Arnoux

Chauvin Arnoux C.A 6011 Manual de usuario

Chauvin Arnoux

Chauvin Arnoux C.A 6470N TERCA 3 Manual de usuario

Chauvin Arnoux

Chauvin Arnoux C.A 6030 Manual de usuario

Chauvin Arnoux

Chauvin Arnoux C.A 6549 Manual de usuario

Chauvin Arnoux

Chauvin Arnoux 6417 Manual de usuario

Chauvin Arnoux

Chauvin Arnoux CA 10002 Manual de usuario

Chauvin Arnoux

Chauvin Arnoux C.A 755 Manual de usuario

Chauvin Arnoux

Chauvin Arnoux C.A 751 Manual de usuario

Chauvin Arnoux

Chauvin Arnoux IMEG 500N Manual de usuario

Chauvin Arnoux

Chauvin Arnoux C.A 6416 Manual de usuario

Chauvin Arnoux

Chauvin Arnoux TERCA 3 Manual de usuario

Chauvin Arnoux

Chauvin Arnoux C.A 6115N Manual de usuario

Chauvin Arnoux

Chauvin Arnoux C.A 10001 Manual de usuario

Chauvin Arnoux

Chauvin Arnoux Green TEST-FTV 100 Manual de usuario

Chauvin Arnoux

Chauvin Arnoux AEMC Instruments 6418 Manual de usuario

Chauvin Arnoux

Chauvin Arnoux CDA 103 Manual de usuario

Chauvin Arnoux

Chauvin Arnoux Metrix DOX2025B Manual de usuario

Chauvin Arnoux

Chauvin Arnoux C.A 6471 Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario