Champion 100204 Manual de servicio

11/8/18 1 Champion Power Equipment, Inc.

Technical Bulletin

Number: 181108-60-50-2

Date: 11/8/18

Recoil Install for 3KW Inverters

This covers the following models (Read completely before performing service):

•100204

•100158

•100387

•75537i

•100476

•100396

•100233

•100264

•100262

•100523

•75531i

•100477

•100263

•100269

•100261

•All similar body style inverters

1. Unscrew the screws and bolts for the left side

panel.

11/8/18 2 Champion Power Equipment, Inc.

2. Unscrew the bolts on the controller module and

take out the controller module.

(If using a remote start or electric start version,

unscrew the bracket with the controller module

and battery (4) bolts. Take out the battery and

unplug all connectors on the controller module and

remove the whole bracket)

Electric/Remote Start Unit:

3. Loosen the cable holder on the recoil cover.

11/8/18 3 Champion Power Equipment, Inc.

4. Unscrew (3) bolts of recoil assembly. Unscrew (2)

screws of handle orientation plate at the panel

side. Take out the recoil assembly with the handle

orientation plate.

5. Pull rope out for some length and secure a stop-

knot at the recoil cover end.

11/8/18 4 Champion Power Equipment, Inc.

6. Remove the recoil handle and orientation plate.

7. Unscrew the bolts of the recoil cover and remove

the recoil assembly

8. Put the new spring into the pulley if need to

replace a new spring.

11/8/18 5 Champion Power Equipment, Inc.

9. Put the new rope into the pulley and secure with

a stop-knot. And then rotate the rope clockwise

[spring side towards to you] (about 3.5 turns)

until the rope aligns with the open slot on the

outer edge of the pulley.

10. Apply lubricant or grease to the shaft of the

recoil cover and insert the pulley to the recoil

cover.

11. Pull the rope into the slot and take the loose part

of the rope inside the pulley and rotate the

pulley about 3 turns [counter-clockwise] until the

tension spring resists. Hold the pulley from

reversing until the rope is ready to wind back

onto the pulley. Feed the rope out to the hole of

recoil cover and pull it through the guide hole on

the outside of the recoil cover. Place the guide

plate / pull handle on the rope and secure with a

stop-knot.

11/8/18 6 Champion Power Equipment, Inc.

12. Place the (2) detent springs as shown

13. Put 2 detents into the spring positions with some

lubricant. Note the detents must press the springs

when install the detents.

11/8/18 7 Champion Power Equipment, Inc.

14. Put the bolt with some lubricant into the press

plate, and then put a spring to the bolt. The bolt

thread can have some locking glue. Put the press

plate assembly onto the detents, and then

tighten the bolt.

11/8/18 8 Champion Power Equipment, Inc.

15. Install the orientation plate with a new recoil

assembly.

16. Install the new recoil assembly. Tighten the cable

holder on the recoil cover.

17. Install the orientation plate.

18. Re-install the controller module. To check all wire

harness and connectors at the suitable position

after installation.

11/8/18 9 Champion Power Equipment, Inc.

19. Re-install the left panel.

If you have any questions regarding the previous procedure, please contact our technical department

Monday-Friday from 8:30 AM-5:00 PM PST at 877-338-0999.

If you have any questions, please contact Champion Power Equipment:

Champion Power Equipment, Inc.

12039 Smith Ave.

Santa Fe Springs, CA 90670

Phone: 1-877-338-0999

Email: [email protected]

Este manual sirve para los siguientes modelos

Otros manuales de Inversor de Champion

Champion

Champion 100544 Manual de usuario

Champion

Champion 100136 Manual de usuario

Champion

Champion ParaLink 100468 Manual de usuario

Champion

Champion 100892 Manual de usuario

Champion

Champion 201003 Manual de usuario

Champion

Champion 73500i Manual de usuario

Champion

Champion 100806 Manual de usuario

Champion

Champion 100692 Manual de usuario

Champion

Champion 100401 Manual de usuario

Champion

Champion LASAR L-1502C Manual de usuario

Champion

Champion 100320 Manual de usuario

Champion

Champion 73001i-DF (EU) Manual del sistema

Champion

Champion 200978 Manual de usuario

Champion

Champion 200977 Manual de usuario

Champion

Champion 92001I-EU Manual de usuario

Champion

Champion 201185 Manual de usuario

Champion

Champion 100199 Manual de usuario

Champion

Champion 200977 Manual de usuario

Champion

Champion 100306 Manual de usuario

Champion

Champion 71001I Manual del sistema

Champion

Champion 200978 Manual de usuario

Champion

Champion 100814 Manual de usuario

Champion

Champion 100269 Manual de usuario

Champion

Champion 200954 Manual de usuario

Manuales populares de Inversor de otras marcas

Fourgroup

Fourgroup Easy Manual de usuario

Velleman

Velleman PI300M Manual de usuario

Sungrow

Sungrow SG350HX-US Manual de usuario

WilTec

WilTec 61897 Manual de usuario

SMA

SMA SUNNY BOY STORAGE 2.5 Manual de usuario

Simplicity

Simplicity LANDLORD 316 Manual de usuario

Santak

Santak SMAX 3000 Manual de usuario

ATON

ATON RA.Store-3 Manual de usuario

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manual de usuario

Tektronix

Tektronix CFG250 Manual de usuario

Vanner

Vanner 20-500 Series Manual de usuario

GE GEP Manual de usuario

Astrel Group

Astrel Group Power Reducer Guía rápida

MULTIQUIP

MULTIQUIP GDP-5H Guía

GoWISE

GoWISE PS1007 Manual de usuario

Promate

Promate PM13500D ES Manual de usuario

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FR-A7AZ Manual de usuario