Challenger CH-1 Manual de usuario

Challenger

CH-1

Product Manual

Challenger

Model No. CH-1

Product Manual

Edition 1 –August 2023

Challenger

CH-1

Product Manual

This Product Manual is an integral part of the product kit.

CHISELfit reserves the right to modify its products and documentation at any time and

without notice.

CHISELfit will accept responsibility for the product only if the following precautions are

observed:

-The product is used in compliance with its specifications.

-The product is used in compliance with the intended purpose as illustrated and

explained in this Product Manual

-Every part of the Product Manual has been carefully read.

-The place of installation meets the requirements in this Product Manual.

-Proper clothing is worn during usage.

CHISELfit is not responsible for any harm due to any failures or damage caused by

unauthorized maintenance, misuse, accident, negligence, improper assembly or

installation, rust or corrosion as a result of the product’s location, alterations or

modifications without CHISELfit’s written authorization or caused by failure on your part

to use, operate and maintain the product as set out in this product manual.

The Challenger is protected by U.S. Patent No. 10,653,914 B2 and U.S. Patent

No. 11,524,206. Other U.S. and worldwide patents pending.

Challenger

CH-1

Product Manual

Table of contents

Table of contents…………………………………………………………………………….3

Usage location and space requirements………………………………………….4

Unboxing and assembly instructions……………………………………………….6

Moving the machine……………………………………………………………………….15

Leveling the machine………………………………………………………………………17

Safety instructions…………………………………………………………………………..18

Product Introduction……………………………………………………………………….19

Operating instructions and information…………………………………………..20

Console functions and operation……………………………………………………..28

Maintenance……………………………………………………………………………………33

Troubleshooting……………………………………………………………………………….34

Technical specifications……………………………………………………………………34

Product label and serial number location…………………………………………35

Service parts and technical support………………………………………………….35

Challenger

CH-1

Product Manual

Usage location and space requirements

For convenience of placement, read and consider the following usage location and

space requirements before unboxing Challenger.

The Challenger must be installed and used in a location that meets the following

requirements.

-Temperature of between 50°F (+10°C) and 80°F (+ 27°C).

-Adequate lighting.

-An open space perimeter of at least 24” (60cm) around the base frame of

Challenger.

-A rigid and stable flat surface that is vibration free and capable of supporting the

combined weight of Challenger and a user mounted on Challenger, given

Challenger’s weight of 395 lbs. (175 kgs) and a maximum user weight of

350 lb.s (159 kgs.)

Do not install Challenger on a soft or floating floor.

Do not expose Challenger to direct sunlight.

Do not use Challenger outdoors or leave Challenger outside or exposed to weather

elements.

Do not place Challenger in high moisture indoor environments such as near

swimming pools, hot tubs, saunas or shower areas.

There should be no people, pets or objects within the exercise area as illustrated

below in drawings 1 and 2. If anything enters the exercise area stop exercising on

Challenger immediately and do not resume exercising on Challenger until the

exercise area is clear.

Challenger

CH-1

Product Manual

Exercise space requirements

Challenger

CH-1

Product Manual

Unboxing and Assembly Instructions

*Two people each capable of lifting at least 100 lbs. / 45 kg. are required to

assemble Challenger. Never attempt to assembly Challenger alone.

*Never open box when it is on its side.

1. Remove all of the unassembled components and the hardware pack and

place them in the work area such that each part is easily identifiable.

2. With the exercise frame still in its lowest position, carefully cut away the

dust cover bag from the exercise frame such that entire top of the

exercise frame is exposed. Be careful not to damage any components of

the machine when cutting away the bag.

3. With the exercise frame still in its lowest position, remove the small

vertical card board tubes supporting the left and right side upper swing

arms and lower swing arms.

4. As illustrated in drawing 3, connect the lower swing arms to the upper

swing arms by fastening the lower swing arms clevis axles to the upper

swing arms clevis forks with a No. 162 bolt and No. 174 acorn nut. Make

certain that the acorn nuts are securely fastened on the outer side of

the clevis forks as illustrated.

Challenger

CH-1

Product Manual

5. With the exercise frame still in its lowest position, screw the threaded

end of each gas spring into each attachment clevis as illustrated in

drawing 4. Once the gas springs are fully threaded into each attachment

clevis allow the bottom end of each gas spring to rest against the curved

cross frame bar.

6. Retrieve 2 each No. 143 bolts and 2 each No. 169 nuts from the

hardware pack and have them at the ready.

7. With the first assembly person ready with the No. 143 bolts and No. 169

nuts, the second assembly person will grasp the black angle adjustment

lifting handles and squeeze the yellow latching levers against the black

lifting handles. While squeezing the yellow latching levers, lift the angle

adjustment arm off of the cardboard support and move the exercise

frame up to its highest angle.

Challenger

CH-1

Product Manual

8. As also illustrated in drawing 4, while the second assembly person is

holding the exercise frame in its highest position, the first assembly

person will connect the lower ends of the gas springs to the lower

attachment brackets with the No 143 bolts and No. 169 nuts. Make

certain the No. 169 nuts are securely fastened to the No. 143 bolts.

Attaching the gas springs

Challenger

CH-1

Product Manual

9. As illustrated in drawing 5, securely fasten each left and right mounting step to the

mounting step support frame with 4 each No. 131 bolts.

Challenger

CH-1

Product Manual

10. As illustrated in drawing 6, securely fasten the left and right forward carriage

stops to the angle carriage support rail with 2 each No. 127 screws.

Tabla de contenidos

Manuales populares de Equipo de fitness de otras marcas

NSD

NSD PB-188P Manual de usuario

Performance

Performance HyperVibe Manual de usuario

Scalamobil

Scalamobil S27 Manual de usuario

Precor

Precor Experience Series Manual de usuario

FYTTER

FYTTER RedMIUM BENCH BE-T6R Manual de usuario

Taurus

Taurus TF-RK1312 Manual de usuario

Nustep

Nustep T5 Manual de usuario

Precor

Precor CW-507 Manual de usuario

Movement

Movement BICEPS Idea Manual de usuario

Kegel8

Kegel8 V For Men Manual de usuario

Skandika

Skandika Styrke II Manual de usuario

BLK BOX

BLK BOX 21-0122-0B Manual de usuario

Stamina

Stamina aeropilates premier 299 Manual de usuario

SPORTSTECH

SPORTSTECH PBX300 Manual de usuario

ParaBody

ParaBody Serious Steel 877102 Manual de usuario

Weslo

Weslo Gym 650 Manual de usuario

Rebel

Rebel ACTIVE RBA-1011 Manual de usuario

4iiii

4iiii FLiiiight Manual de usuario