Central Pneumatic 93506 Manual de usuario
QUICK CHANGE AIR BRUSH KIT
Model 93506
ASSEMBLY and OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
For technical questions and replacement parts, please call 1-800-444-3353
®
Copyright © 2005 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Page 2SKU 93506 For technical questions, please call 1-800-444-3353
Specifications
Save This Manual
You will need the manual for the safety warnings and precautions, assembly instruc-
tions, operating and maintenance procedures, parts list and diagram. Keep your in-
voice with this manual. Write the invoice number on the inside of the front cover. Keep
the manual and invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using tool, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.
Read all instructions before using this tool!
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Don’t expose to rain. Keep work area well lit. Do
not use a propellant can in the presence of flammable gases or liquids. Always
spray in a well ventilated area.
3. Keep children and bystanders away. Children must never be allowed in the work
area. Do not let them handle machines, tools, extension cords, or air hoses.
4. Store idle equipment. When not in use, tools must be stored in a dry location to
inhibit rust. Always lock up tools and keep out of reach of children.
5. Use the right tool for the job. Do not attempt to force a small tool or attachment
to do the work of a larger industrial tool. There are certain applications for which
this tool was designed. It will do the job better and more safely at the rate for
which it was intended. Do not modify this tool and do not use this tool for a
purpose for which it was not intended.
6. Use eye and nose protection. Wear, and ensure all people in the work area
wear, ANSI approved impact safety goggles and an ANSI approved dust mask or
respirator.
7. Maintain tools with care. Keep Air Brush clean for better and safer performance.
Follow instructions for changing accessories.
8. Do not overreach. Keep proper footing and balance at all times.
Fluid Capacity 3/4 oz.
Air Inlet 1/4” NPT
Working Pressure 15 to 50 PSI
Fluid Jar Size (Qty. 5) 1-3/8” Dia. x 2” H
Air Brush Dimensions 5-1/2” x 1-3/8” x 3-3/4”
Note: This Air Brush works with a regulated small air compressor with an air regulator (none
included). The air pressure must not exceed 50 PSI.
Page 3SKU 93506 For technical questions, please call 1-800-444-3353
9. Stay alert. Watch what you are doing, use common sense. Do not operate any
tool when you are tired.
10. Check for damaged parts. Before using any tool, any part that appears damaged
should be carefully checked to determine that it will operate properly and perform
its intended function. Check for alignment and binding of moving parts; any
broken parts or mounting fixtures; and any other condition that may affect proper
operation. Any part that is damaged should be properly repaired or replaced by a
qualified technician.
11. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use
accessories intended for use with this tool. Approved accessories are available
from Harbor Freight Tools.
12. Do not operate tool if under the influence of alcohol or drugs. Read warning
labels if taking prescription medicine to determine if your judgement or reflexes
are impaired while taking drugs. If there is any doubt, do not operate the Air
Brush.
13. Maintenance. For your safety, maintenance should be performed regularly by a
qualified technician.
14. Use compressed air from a small, regulated air compressor. Use clean, dry
regulated air at 15 to 50 PSI. Never use oxygen, carbon dioxide, combustible
gases, or any other bottled gas as a power source for this tool.
Warning: The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be under-
stood by the operator that common sense and caution are factors which cannot be
built into this product, but must be supplied by the operator.
Unpacking
When unpacking, check to make sure the parts listed on page 6 are included. If any
parts are missing or broken, please call Harbor Freight Tools at the number on the
cover of this manual as soon as possible.
WARNING: The brass components of this product contain lead, a chemical known
to the State of California to cause birth defects (or other reproductive harm).
(California Health & Safety code 25249.5, et seq.)
Page 4SKU 93506 For technical questions, please call 1-800-444-3353
Operation
FIGURE 1
Air Tip (7)
Fluid Cap (1)
Jar (6)
Jar Adapter (3)
Lever (9)
Air Hose (16)
Air Valve Connector (15)
Mixing and Thinning Paints
Before attempting to spray any paints through the Spray Gun, dilute them accord-
ing to the manufacturer’s directions, for use with Spray Guns.
General Rules:
1. If mixing colors, only mix together the same types of paints (i.e. lacquer with lacquer
or acrylic with acrylic).
2. Thin paint according to paint manufacturer’s directions. Typically, enamel and lac-
quer paints are diluted with one part thinner to one part paint.
3. Before spraying make sure the diluted paint is thoroughly mixed.
4. Mix the paint in a clean jar. We recommend straining the paint before filling the Jar
(6).
Attaching the Air Hose (16) and the Jar (6) to the air supply
1. Fill the Jar (6) with strained paint. Do not fill over 2/3 full.
2. Carefully thread on the Jar Lid (3).
3. Attach one end of the Air Hose (16) to the Air Inlet (15) on the Air Brush. Attach the
other end of the Air Hose (16) to the regulator (not included) which then attaches to
the air supply using the 1/4” NPT Adapter (17). The air source must be adjustable
between 15 and 50 PSI. Thoroughly read the instructions and safety warnings
provided with the air compressor and air regulator before using.
Page 5SKU 93506 For technical questions, please call 1-800-444-3353
Adjusting Paint Flow and Air Flow
1. Use the air regulator (not included) to regulate air flow. You must purchase a regu-
lator that can be adjusted to between 15 and 50 PSI. Since there is no pressure
gauge you will have to test the Air Brush on a piece of scrap material to determine
the desired setting.
2. On the Air Brush, turn the Fluid Cap (1) to adjust paint flow. For maximum flow,
turn the cap counterclockwise. For minimum flow, turn the cap clockwise. See
FIGURE 1 on page 4 and the assembly drawing on page 6.
Spray Painting
1. In a well ventilated area, press the Lever (9) to test the spray on test material. Hold
the Air Brush six inches from the material and make the necessary adjustments.
2. Practice spraying even strokes to avoid drips.
Note: Since enamels and lacquer paints dry quickly, do not leave the Air Brush for more
than a few seconds or the paint may dry and clog the Air Brush.
3. Have a spare Jar (6) filled with thinner or water, depending on the type of paint be-
ing sprayed.
4. When finished spraying, release pressure on the Lever (9). Immediately remove
the paint jar from the Air Brush and attach the spare Jar (6). Continuously spray
on scrap white paper until the paint residue in the Air Brush is sprayed out.
Cleaning
1. Remove excess paint from the Jar (6) and clean thoroughly.
2. Spray thinner or water (depending on the paint used) through the Air Brush until it
is entirely clean. Plug up the Fluid Cap (1) with a soft cloth and force air and solu-
tion through the cap and tip.
Troubleshooting
If the Air Brush becomes clogged, disconnect from the air source and clean as
stated above. Next, gently un-thread (counterclockwise) the Fluid Cap (1) and Air
Tip (7). Clean the parts in thinner and replace.
Page 6SKU 93506 For technical questions, please call 1-800-444-3353
NOTE: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBU-
TOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE
IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Parts List and Assembly Drawing
Note: #17 1/4” NPT Adapter (not shown)
Part Description
1 Fluid Cap
2 O-ring
3 Jar Lid
4 Tube
5 Cover Gasket
6 Jar (3/4 oz.) Qty. 5
7 Air Tip
8 O-ring
9 Lever
10 Body
11 O-ring
12 Air Valve Pin
13 O-ring
14 Air Valve Spring
15 Air Inlet
16 Air Hose
17 1/4” NPT Adapter
Page 7SKU 93506 For technical questions, please call 1-800-444-3353
90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability stan-
dards, and warrants to the original purchaser that this product is free from defects in materials and workman-
ship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly
or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal ac-
tivity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for
death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising
from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN
LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MER-
CHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If
our inspection veries the defect, we will either repair or replace the product at our election or we may elect to
refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return re-
paired products at our expense, but if we determine there is no defect, or that the defect resulted from causes
not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specic legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Tabla de contenidos
Otros manuales de Pistola pulverizadora de pintura de Central Pneumatic
Central Pneumatic
Central Pneumatic 66801 Manual de instalación
Central Pneumatic
Central Pneumatic HVLP DETAIL SPRAY GUN 46719 Manual de usuario
Central Pneumatic
Central Pneumatic HVLP DETAIL SPRAY GUN 46719 Manual de usuario
Central Pneumatic
Central Pneumatic 86 Manual de instalación
Central Pneumatic
Central Pneumatic 94605 Manual de lista de piezas
Central Pneumatic
Central Pneumatic 00422 Manual de usuario
Central Pneumatic
Central Pneumatic CENTRAL PNEUMATIC 92841 Manual de usuario
Central Pneumatic
Central Pneumatic 66871 Manual de instalación
Central Pneumatic
Central Pneumatic 47016 67181 Instrucciones de montaje
Central Pneumatic
Central Pneumatic 62381 Manual de usuario
Central Pneumatic
Central Pneumatic 43760 Manual de usuario
Central Pneumatic
Central Pneumatic 96382 Manual de lista de piezas
Central Pneumatic
Central Pneumatic 91011 Manual de usuario
Central Pneumatic
Central Pneumatic 91011 Manual de usuario
Central Pneumatic
Central Pneumatic 69724 Instrucciones de montaje
Central Pneumatic
Central Pneumatic 93205 Manual de usuario
Central Pneumatic
Central Pneumatic 97855 Manual de instalación
Central Pneumatic
Central Pneumatic 99959 Manual de instalación
Central Pneumatic
Central Pneumatic 47016 Guía del usuario
Central Pneumatic
Central Pneumatic CENTRAL PNEUMATIC 93305 Guía del usuario
