Central Pneumatic 67100 Manual de instalación

METAL CONNECTOR NAILER

67100

SET UP AND OPERATING INSTRUCTIONS

Distributed exclusively by Harbor Freight Tools®.

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

Read and understand tool labels and

manual. Failure to follow warnings could

result in DEATH or SERIOUS INJURY.

SAVE THIS MANUAL.

contained herein may be reproduced in any shape or form without the express written consent of

Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein. Tools required for

assembly and service may not be included.

For technical questions or replacement parts, please call 1-800-444-3353.

SKU 67100 For technical questions, please call 1-800-444-3353. Page 2

SAVE THIS MANUAL

Keep this manual for the safety warn-

ings and precautions, assembly, operat-

ing, inspection, maintenance and cleaning

procedures. Write the product’s serial

number in the back of the manual near the

assembly diagram (or month and year of

purchase if product has no number). Keep

this manual and the receipt in a safe and

dry place for future reference.

Safety Alert Symbol and Signal

Words

In this manual, on the labeling,

and all other information provid-

ed with this product:

This is the safety alert

symbol. It is used to alert

you to potential personal

injury hazards. Obey all

safety messages that

follow this symbol to avoid

possible injury or death.

DANGER indicates

a hazardous

situation which, if not

avoided, will result in death or

serious injury.

WARNING

indicates a

hazardous situation which, if

not avoided, could result in

death or serious injury.

CAUTION, used

with the safety

alert symbol, indicates a

hazardous situation which, if

not avoided, could result in

minor or moderate injury.

NOTICE is used to

address practices

not related to personal injury.

CAUTION, without

the safety alert

symbol, is used to address

practices not related to

personal injury.

Symbol Denitions

Symbol Property or statement

PSI Pounds per square inch of pressure

CFM Cubic Feet per Minute ow

SCFM Cubic Feet per Minute ow at

standard conditions

NPT National pipe thread, tapered

NPS National pipe thread, straight

WARNING marking concerning Risk

of Eye Injury. Wear ANSI-approved

safety goggles with side shields.

Warning marking concerning Risk of

Puncture Injury. Wear heavy-duty

work gloves.

Read the manual before set-up and/

or use.

WARNING marking concerning Risk

of Hearing Loss. Wear hearing

protection.

WARNING marking concerning Risk

of Respiratory Injury. Wear NIOSH-

approved dust mask/respirator.

WARNING marking concerning Risk

of Explosion.

SKU 67100 For technical questions, please call 1-800-444-3353. Page 3

IMPORTANT SAFETY

INSTRUCTIONS

INSTRUCTIONS PERTAINING

TO A RISK OF FIRE,

ELECTRIC SHOCK, OR

INJURY TO PERSONS

WARNING – When using tools, basic pre-

cautions should always be followed,

including the following:

General

a. To reduce the risks of electric

shock, re, and injury to persons,

read all the instructions before us-

ing the tool.

Work area

a. Keep the work area clean and well

lighted. Cluttered benches and dark

areas increase the risks of electric

shock, re, and injury to persons.

b. Do not operate the tool in explo-

sive atmospheres, such as in the

presence of ammable liquids,

gases, or dust. The tool is able to

create sparks resulting in the ignition

of the dust or fumes.

c. Keep bystanders, children, and

visitors away while operating the

tool. Distractions are able to result in

the loss of control of the tool.

Personal safety

a. Stay alert. Watch what you are do-

ing and use common sense when

operating the tool. Do not use the

tool while tired or under the inu-

ence of drugs, alcohol, or medica-

tion. A moment of inattention while

operating the tool increases the risk

of injury to persons.

b. Dress properly. Do not wear loose

clothing or jewelry. Contain long

hair. Keep hair, clothing, and

gloves away from moving parts.

Loose clothes, jewelry, or long hair

increases the risk of injury to persons

as a result of being caught in moving

parts.

c. Avoid unintentional starting. Be

sure the trigger is released before

connecting to the air supply. Do not

carry the tool with your nger on the

trigger or connect the tool to the air

supply with the trigger pressed.

d. Do not overreach. Keep proper

footing and balance at all times.

Proper footing and balance enables

better control of the tool in unexpect-

ed situations.

e. Use safety equipment. A

dust mask, non-skid safety

shoes and a hard hat must

be used for the applicable

conditions. Wear heavy-duty work

gloves during use.

f. Always wear eye protec-

tion. Wear ANSI-ap-

proved safety goggles with

side shields.

g. Always wear hearing

protection when using

the tool. Prolonged expo-

sure to high intensity noise

is able to cause hearing loss.

h. Do not attach the hose or tool to

your body. Attach the hose to the

structure to reduce the risk of loss of

balance if the hose shifts.

SKU 67100 For technical questions, please call 1-800-444-3353. Page 4

i. Always assume that the tool con-

tains fasteners. Do not point the tool

toward yourself or anyone whether it

contains fasteners or not.

j. WARNING – Do not re fastener on

top of another fastener. This is able

to cause the fastener to be deected

and hit someone, or cause the tool to

react and result in a risk of injury to

persons.

k. WARNING – Remove nger from

the trigger when not driving fas-

teners. Never carry the tool with

nger on trigger, the tool is able to re

a fastener.

Tool use and care

a. Use clamps or another practical

way to secure and support the

workpiece to a stable platform.

Holding the work by hand or against

the body is unstable and can lead to

loss of control.

b. Do not force the tool. Use the

correct tool for the application. The

correct tool will do the job better and

safer at the rate for which the tool is

designed.

c. Do not use the tool if the trigger

does not turn the tool on or off.

Any tool that cannot be controlled

with the trigger is dangerous and

must not be used until repaired.

d. Disconnect the tool from the air

source before making adjust-

ments, doing tool maintenance,

clearing jams, touching the safety

nosepiece, leaving work area,

loading, or unloading the tool.

Such precautionary measures reduce

the risk of injury to persons.

e. Store the tool when it is idle out of

reach of children and other un-

trained persons. A tool is dangerous

in the hands of untrained users.

f. Maintain the tool with care. A prop-

erly maintained tool reduces the risk

of binding and is easier to control.

g. Check for misalignment or bind-

ing of moving parts, breakage of

parts, and any other condition that

affects the tool’s operation. If dam-

aged, have the tool serviced before

using. Many accidents are caused

by poorly maintained tools. There is a

risk of bursting if the tool is damaged.

h. Use only accessories that are

identied by the manufacturer for

the specic tool model. Use of an

accessory not intended for use with

the specic tool model, increases the

risk of injury to persons.

i. Use only those fasteners listed

in the Specications chart of this

manual. Fasteners not identied for

use with this tool by the tool manu-

facturer are able to result in a risk

of injury to persons or tool damage

when used in this tool.

Service

a. Tool service must be performed

only by qualied repair personnel.

b. When servicing a tool, use only

identical replacement parts. Use

only authorized parts.

c. Use only the lubricants supplied

with the tool or specied by the

manufacturer.

SKU 67100 For technical questions, please call 1-800-444-3353. Page 5

Air source

a. Never connect to an air

source that is capable of

exceeding 115 PSI. Over

pressurizing the tool may

cause bursting, abnormal operation,

breakage of the tool or serious injury

to persons. Use only clean, dry,

regulated compressed air at the rated

pressure or within the rated pressure

range as marked on the tool. Always

verify prior to using the tool that the

air source has been adjusted to the

rated air pressure or within the rated

air-pressure range.

b. Never use oxygen, carbon dioxide,

combustible gases or any bottled

gas as an air source for the tool.

Such gases are capable of explosion

and serious injury to persons.

SAVE THESE

INSTRUCTIONS.

SPECIFIC SAFETY

INSTRUCTIONS

1. Operators and others in work area

MUST wear ANSI-approved safety

goggles with side shields during

use. The employer is responsible to

enforce the use of eye protection by

the operator and others in the work

area.

2. Keep ngers away from trigger

when not driving fasteners to

avoid accidental ring.

3. Choice of triggering method is im-

portant. Check manual for trigger-

ing options.

4. Always assume the tool contains

fasteners.

5. Do not point the tool toward yourself

or anyone whether it contains fasten-

ers or not.

6. Do not actuate the tool unless the

tool is placed rmly against the work-

piece.

7. Respect the tool as a working imple-

ment.

8. No horseplay. This tool is not a toy

and can be deadly if misused.

9. Do not load the tool with fasteners

when any one of the operating con-

trols, such as the Trigger or Safety

Nosepiece, is activated.

10. Do not remove, tamper with, or other-

wise cause the tool operating controls

to become inoperable.

11. Do not operate the tool if any portion

of the tool operating controls is inop-

erable, disconnected, altered, or not

working properly.

12. Disconnect the tool from the air sup-

ply when:

a. Unattended.

b. Performing any maintenance or

repair.

c. Clearing a jam.

d. Moving the tool to a new location.

13. Do not make any modications to this

tool.

14. Refer to the tool maintenance instruc-

tions for detailed information on the

proper maintenance of the tool.

15. Fire fasteners into an appropriate

work surface only. Do not attempt to

SKU 67100 For technical questions, please call 1-800-444-3353. Page 6

re fasteners into surfaces too hard

to penetrate. Do not drive fasteners

on top of other fasteners, or at too

steep of an angle. Fasteners can

ricochet causing personal injury.

16. Do not re fasteners too close to the

edge of a workpiece. They may split

the workpiece and y free, causing

personal injury.

17. Keep clear of the workpiece near the

area being fastened. Fasteners may

bend sideways during ring, caus-

ing them to exit the workpiece at an

unexpected point, causing personal

injury.

18. Transport Tool safely. Always dis-

connect air supply when moving the

tool. Carry the tool by the handle and

avoid contact with the trigger.

19. Hold tool away from head and body.

During operation the Tool may kick

back causing injury.

20. Do not re fasteners into a workpiece

that has people, utility lines, or other

objects behind or inside it.

21. Keep balance while using this tool.

Keep area below clear if working in

an elevated location, and secure air

hose to prevent falls from bystanders

accidentally pulling on it.

22. Obey the manual for the air compres-

sor used to power this tool.

23. Install an in-line shutoff valve to allow

immediate control over the air supply

in an emergency, even if a hose is

ruptured.

24. Do not engrave or stamp anything

into the housing to prevent weaken-

ing of the housing.

25. WARNING: Some dust created by

power sanding, sawing, grinding, drill-

ing, and other construction activities,

contains chemicals known [to the

State of California] to cause cancer,

birth defects or other reproductive

harm. Some examples of these

chemicals are:

• Lead from lead-based paints

• Crystalline silica from bricks and

cement or other masonry products

• Arsenic and chromium from chemi-

cally treated lumber

Your risk from these exposures var-

ies, depending on how often you do

this type of work. To reduce your

exposure to these chemicals: work in

a well ventilated area, and work with

approved safety equipment, such as

those dust masks that are specially

designed to lter out microscopic

particles. (California Health & Safety

Code § 25249.5, et seq.)

26. WARNING: The brass components

of this product contain lead, a chemi-

cal known to the State of California

to cause birth defects (or other repro-

ductive harm). (California Health &

Safety code § 25249.5, et seq.)

27. The warnings and precautions dis-

cussed in this manual cannot cover

all possible conditions and situations

that may occur. It must be under-

stood by the operator that common

sense and caution are factors which

cannot be built into this product, but

must be supplied by the operator.

Vibration Precautions

This tool vibrates during use. Re-

peated or long-term exposure to vibra-

tion may cause temporary or permanent

physical injury, particularly to the hands,

SKU 67100 For technical questions, please call 1-800-444-3353. Page 7

arms and shoulders. To reduce the risk of

vibration-related injury:

1. Anyone using vibrating tools regu-

larly or for an extended period should

rst be examined by a doctor and

then have regular medical check-

ups to ensure medical problems are

not being caused or worsened from

use. Pregnant women or people

who have impaired blood circulation

to the hand, past hand injuries, ner-

vous system disorders, diabetes, or

Raynaud’s Disease should not use

this tool. If you feel any symptoms

related to vibration (such as tingling,

numbness, and white or blue ngers),

seek medical advice as soon as pos-

sible.

2. Do not smoke during use. Nico-

tine reduces the blood supply to the

hands and ngers, increasing the risk

of vibration-related injury.

3. Wear suitable gloves to reduce the

vibration effects on the user.

4. Use tools with the lowest vibration

when there is a choice between dif-

ferent processes.

5. Include vibration-free periods each

day of work.

6. Grip tool as lightly as possible (while

still keeping safe control of it). Let

the tool do the work.

7. To reduce vibration, maintain tool as

explained in this manual. If abnormal

vibration occurs, stop immediately.

SAVE THESE

INSTRUCTIONS.

FUNCTIONAL DESCRIPTION

Specications

Operating Air

Pressure

70-115 PSI*

*For fasteners 1” or longer into

workpieces at least 13/4” thick.

Air Inlet 1/4” -18 NPT

Air Consumption 6 CFM @ 90 PSI

Fastener

Capacity

1-1/2” Long, 35° Angle, Paper

Collated Metal Connector Nails

Magazine

Capacity 35 Nails

Safety Full Sequential

Components and Controls

Safety Nosepiece - Also called the work-

piece contact, the Safety Nosepiece

helps prevent the tool from ring un-

less it is pressed against an object.

The Nailer also comes with three ad-

justing wrenches (3, 4 and 5mm) and

a bottle of lubricating oil.

INITIAL TOOL SET UP/

ASSEMBLY

Read the ENTIRE IMPORTANT

SAFETY INFORMATION

section at the beginning of this

manual including all text under

Air Inlet

Trigger

Nose

Trigger

Lock

Magazine

Rev 09f

SKU 67100 For technical questions, please call 1-800-444-3353. Page 8

subheadings therein before set

up or use of this product.

Note: For additional information regarding

the parts listed in the following pages,

refer to the Assembly Diagram near

the end of this manual.

Unpacking

When unpacking, make sure item is

intact and undamaged. If parts are miss-

ing or broken, call Harbor Freight Tools at

1-800-444-3353 as soon as possible.

• This air tool may be shipped with a

protective plug covering the air inlet.

Remove this plug before set up.

Air Supply

TO PREVENT

EXPLOSION:

Use only clean, dry, regulated,

compressed air to power this

tool. Do not use oxygen,

carbon dioxide, combustible

gases, or any other bottled

gas as a power source for this

tool.

Quick

Coupler

Recommended Air Line Components

Regulator with

Pressure Gauge

Quick

Coupler Air Hose

on Reel

Valve FilterOiler

Coupler

Plug

Tool

Air

Compressor

Coupler

Plug

1. Incorporate a lter, regulator with

pressure gauge, oiler, in-line shutoff

valve, and quick coupler for best ser-

vice, as shown in the diagram above.

An in-line shutoff ball valve is an

important safety device because it

controls the air supply even if the

air hose is ruptured. The shutoff

valve should be a ball valve be-

cause it can be closed quickly.

Note: If an automatic oiler system is not

used, add a few drops of Pneumatic

Tool Oil into the airline connection be-

fore operation. Add a few more drops

after each hour of continual use.

2. Attach an air hose to the compres-

sor’s air outlet. Connect the air hose

to the air inlet of the tool. Other com-

ponents, such as a coupler plug and

quick coupler, will make operation

more efcient, but are not required.

WARNING! TO PREVENT SERIOUS

INJURY FROM ACCIDENTAL

OPERATION:

Do not install a female quick

coupler on the tool. Such a coupler

contains an air valve that will allow

the air tool to retain pressure and

operate accidentally after the air

supply is disconnected.

Note: Air ow, and therefore tool perfor-

mance, can be hindered by under-

sized air supply components.

3. The air hose must be long enough

to reach the work area with enough

extra length to allow free movement

while working.

4. Release the Trigger.

5. Close the in-line safety valve be-

tween the compressor and the tool.

SKU 67100 For technical questions, please call 1-800-444-3353. Page 9

6. Turn on the air compressor according

to the manufacturer’s directions and

allow it to build up pressure until it

cycles off.

7. Adjust the air compressor’s output

regulator so that the air output is

enough to properly power the tool,

but the output will not exceed the

tool’s maximum air pressure at any

time. Adjust the pressure gradually,

while checking the air output gauge

to set the right pressure range.

8. The air pressure setting must not ex-

ceed job site regulations/restrictions.

The air pressure setting must not ex-

ceed 115 PSI when being used with

work pieces that have a thickness of

less than 1-3/4”.

9. Inspect the air connections for leaks.

Repair any leaks found.

10. If the tool will not be used at this

time, turn off and detach the air sup-

ply, safely discharge any residual air

pressure, and release the trigger to

prevent accidental operation.

Note: Residual air pressure should not be

present after the tool is disconnected

from the air supply. However, it is a

good safety measure to attempt to

discharge the tool in a safe fashion

after disconnecting to ensure that the

tool is disconnected and unpowered.

OPERATING INSTRUCTIONS

Read the ENTIRE IMPORTANT

SAFETY INFORMATION

section at the beginning of this

manual including all text under

subheadings therein before set

up or use of this product.

Inspect tool before use, looking

for damaged, loose, and/or

missing parts. If any problems

are found, do not use tool until

repaired.

Work Piece and Work Area Set Up

1. Designate a work area that is clean

and well-lit. The work area must not

allow access by children or pets to

prevent distraction and injury.

2. Route the air hose along a safe route

to reach the work area without creat-

ing a tripping hazard or exposing the

air hose to possible damage. The air

hose must be long enough to reach

the work area with enough extra

length to allow free movement while

working.

3. Secure loose workpieces using a vise

or clamps (not included) to prevent

movement while working.

4. There must not be hazardous ob-

jects (such as utility lines or foreign

objects) nearby that will present a

hazard while working.

5. Please note: The Nailer will ONLY

re when the Magazine is loaded with

six (6) or more nails.

Full Sequential Safety Trip

Mechanism Denition

This tool has a full sequential safety

trip mechanism, which is designed to

prevent inadvertent ring. The tool should

only re if the end of the nail is pressed

against the workpiece prior to pulling the

Trigger. It should only re again if the Trig-

ger is released. The Tool should not re if

the Nail is not pressed against the work-

piece.

SKU 67100 For technical questions, please call 1-800-444-3353. Page 10

Full Sequential Safety Trip

Mechanism Testing Procedure

TO PREVENT

SERIOUS INJURY

FROM ACCIDENTAL

OPERATION: Point the tool at

a piece of scrap wood when

testing.

1. Disconnect tool from the air supply.

2. Put at least 10 nails in the Magazine

(The Nailer will not re if empty or

with only a few fasteners loaded.)

3. Check that the Trigger and the Nail

move freely and without sticking.

4. Connect air supply to tool and set

within Operating Air Pressure range

indicated on the Specication chart.

5. Push down and turn Trigger Lock

(35) clockwise to unlock Trigger. (See

lock/unlock symbols on housing.)

6. Test tool by pressing the Nail against

the workpiece without pulling the Trig-

ger. The Tool must not cycle (re).

If it cycles (res), stop immediately

and have it repaired by a qualied

service technician.

7. Hold tool away or off of workpiece.

The Nail should return to its original

position. Squeeze Trigger. The tool

must not cycle (re). If tool res,

stop immediately and have it repaired

by a qualied service technician.

8. Press the Nail against the workpiece

and squeeze the Trigger. The tool

must cycle (re) only once. Re-

lease the Trigger and squeeze it

again. The tool must not cycle

(re). With the Trigger held, carefully

lift the tool and press it against the

workpiece again. The tool must not

cycle (re). If it fails to perform in

the manner explained in bold, have it

repaired by a qualied service techni-

cian.

Loading/Unloading Nailer

TO PREVENT

SERIOUS INJURY

FROM ACCIDENTAL

OPERATION, BEFORE

LOADING:

• Wear ANSI-approved safety

goggles with side shields.

Other people in the work area

must also wear ANSI-approved

safety goggles with side shields.

• Release the trigger.

• Detach the air supply.

• Attempt to re the Tool into a

piece of scrap wood to ensure

that there is no trapped air

and is incapable of ring any

fasteners.

1. To load nails, hold Nailer with Nose

(74) pointing downward and insert

stick of metal connecting nails into

back of Magazine (85).

2. Slide nail stick (not included) all the

way to front of Magazine.

3. Pull Pusher (84) towards back of

Magazine and past last nail. Release

Pusher, allowing it to engage with nail

stick.

4. To unload nails, press down on Push-

er Latch (81) to disengage Pusher

from Nails.

5. Slowly slide Pusher past the nails

and toward Nose.

Tabla de contenidos

Otros manuales de Pistola de clavos de Central Pneumatic

Central Pneumatic

Central Pneumatic 68247 Instrucciones de montaje

Central Pneumatic

Central Pneumatic 68021 Manual de instalación

Central Pneumatic

Central Pneumatic Central Pneumatic Air Nailer/Stapler 2-in-1 Kit... Manual de usuario

Central Pneumatic

Central Pneumatic 98917 Manual de instalación

Central Pneumatic

Central Pneumatic 4041 Manual de usuario

Central Pneumatic

Central Pneumatic 92359 Manual de instalación

Central Pneumatic

Central Pneumatic 69450 Manual de usuario

Central Pneumatic

Central Pneumatic 97586 Manual de usuario

Central Pneumatic

Central Pneumatic 97525 Manual de usuario

Central Pneumatic

Central Pneumatic 68068 Instrucciones de montaje

Central Pneumatic

Central Pneumatic 47612 Contractor Series Manual de instalación

Central Pneumatic

Central Pneumatic Professional 97512 Manual de usuario

Central Pneumatic

Central Pneumatic 39092 Manual de usuario

Central Pneumatic

Central Pneumatic 68021 Manual de instalación

Central Pneumatic

Central Pneumatic 93909 Manual de instalación

Central Pneumatic

Central Pneumatic 67450 Manual de instrucciones original

Central Pneumatic

Central Pneumatic 98751 Guía del usuario

Central Pneumatic

Central Pneumatic 69575 Instrucciones de montaje

Central Pneumatic

Central Pneumatic 66872 Manual de usuario

Central Pneumatic

Central Pneumatic 66902 Manual de instalación

Central Pneumatic

Central Pneumatic Contractor 97520 Manual de usuario

Central Pneumatic

Central Pneumatic 93496 Manual de usuario

Central Pneumatic

Central Pneumatic 68023 Manual de instalación

Central Pneumatic

Central Pneumatic 90193 Manual de usuario

Manuales populares de Pistola de clavos de otras marcas

Performance Tool

Performance Tool M643 Manual de usuario

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Manual de usuario

Parkside

Parkside PET 25 B1 Manual de usuario

Senco

Senco Fusion Technology F-35XP Manual de usuario

Grizzly

Grizzly G1847 Manual de usuario

Ryobi

Ryobi R18N18G Manual de usuario

Black & Decker

Black & Decker 492848-00 Manual de usuario

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Manual de usuario

Metabo HPT

Metabo HPT NR 3690DC Manual de instrucciones

Surtek

Surtek CN650 Dimensiones y guía de instalación

Makita

Makita GF600 Manual de usuario

Parkside

Parkside PET 25 B1 Manual de usuario

Senco

Senco AirFree 25 Manual de usuario

Freeman

Freeman P50LSLW Manual de usuario

Aicon PRO

Aicon PRO DAC4507 Manual de usuario

DAJ

DAJ XR150A Manual de usuario

Makita

Makita AN923 Manual de usuario

Grizzly

Grizzly T20644 Manual de usuario