CEL-FI PRO Manual de usuario
For more information, videos, & support,
please visit cel-fi.com.
Step 1Step 3
Step 2
Cel-Fi PRO Set-up
NETWORK UNIT COVERAGE UNIT
User Interface
LCD Screen On/Off Button
for LCD Backlighting
Optimal Coverage
from CU to NU
For Cel-Fi PRO to work correctly, use
your phone to find the best 3G, 4G or
LTE signal. Typically, you will get the
best signal upstairs near a window.
The NU and CU communicate with each other wirelessly to provide the best signal improvement possible. As the
distance between the units is increased, the CU adjusts its coverage bubble to provide the ideal amount of coverage.
Place the NU in the location where you
get the best cellular signal.
Place the CU in the location where
you need improved coverage.
Congratulations! Your Cel-Fi Smart
Signal Booster is now working.
Find the best cellular signal.
Optimize Coverage by moving the Coverage Unit.
Place the Network Unit (NU). Place the Coverage Unit (CU).
NOTE:
Your device may require REGISTRATION
prior to use. If so, please refer to the
included Device Registration sheet
included with the unit.
NETWORK UNIT Too FarToo Close Modest Coverage Good Coverage Best Coverage
COVERAGE UNIT COVERAGE UNIT COVERAGE UNIT COVERAGE UNIT
Signal Strength
BEST
4-5 BARS
BETTER
2-3 BARS
OK
1 BAR
Slide Coverage
Unit until secure.
Coverage Unit
Upside Down
Each Cel-Fi device may be supplied with mounting brackets and hardware to
mount both (or either) the Coverage Unit and the Network Unit.
NOTE: The brackets come equipped with screws and inserts for mounting in
standard drywall. Before you install the mounts, make sure there are no
wires or other objects, or metal plates, behind the drywall layer that will
interfere with the inserts, screws, mount, or mounted units.
NOTE: The Network Unit only has mounting holes on the back. The
Coverage Unit has mounting holes on the bottom and on the back. The
holes on the bottom of the Coverage Unit can be used for mounting the
Coverage Unit on a ceiling (See fig 7).
REQUIRED HARDWARE
Mounting
Brackets (2)
Network Unit Coverage Unit
Screws (4)
Drywall Anchors (4)
CONTENTS OF YOUR BOX
Quick Start Guide
Power Adapters (2)
IMPORTANT: Your Cel-Fi PRO Signal Booster is electronic equipment. Both units
must be kept indoors and in a dry, cool, well ventilated area.
NETWORK UNIT COVERAGE UNIT
In each marked spot, use a 3/16” drill bit to drill guide holes for the anchors.
1Determine Cel-Fi Device Location (refer to other side).
2
Determine Mounting Hole Locations.
3
Drill Anchor Holes (Drywall).
4
Install Anchors (Drywall).
6Attach the Cel-Fi Unit to the wall mounted bracket.
NETWORK UNIT COVERAGE UNIT
(x4)
(x4)
5Install Mounting Bracket.
7
To ensure ceiling mounting is as secure as possible, confirm that the mounting bracket posts
are firmly inserted, and in the correct position.
Mounting
Posts
Optional: Attach the Cel-Fi Unit to a ceiling mounted bracket.
Mounting Instructions
Copyright © 2016 by Nextivity, Inc, U.S. Patents pending. All rights reserved. The Nextivity and Cel-Fi
logos are registered trademarks of Nextivity Inc. All other trademarks or registered trademarks listed
belong to their respective owners. Designed by Nextivity Inc in California.
Figure 2. Coverage Unit, bottom view of mounting holes.
Bottom Mounting Holes
Coverage Unit
Figure 1. Coverage Unit, back view with mounting holes.
Back Mounting Holes
Coverage Unit
Network Unit
Figure 3. Network Unit, back view of mounting holes.
Back Mounting Holes
Dashboard:
Glance-able view to the state of your Cel-Fi
environment.
Settings:
Change the default Operator, setup an external
antenna, name your booster, and more.
Advanced Mode:
Get a real-time technical overview of the
installation of your Cel-Fi Booster.
Booster Updates:
Keep your Cel-Fi Booster up-to-date as new
software versions become available.
Register: (When Required)
Easily register your Cel-Fi Booster.
For more information, and software, go to:
www.cel-fi.com/wave
Cel-Fi WAVE is an application available on both smartphones and desktop
computers that allows users to interact with Cel-Fi, to access advanced and
supplementary features.
Get More from Cel-Fi WAVE
CU 50 feet or more from
the NU yields 100 feet or
more of coverage.
Increase the distance of the CU from the NU to increase the signal strength.
COVERAGE UNIT
(CU)
NETWORK UNIT
(NU)
SIGNAL STRENTH DIAGRAM
Your unit needs to be registered to
operate. Refer to the Registration Guide
included in your product documents.
Troubleshooting
The key to better performance is the placement of the two units.
Please call your cell phone
provider.
(Error 7) Unit disabled by network
Waiting for registration to complete. Run
Phone App or go to www.cel-fi.com/register
Try moving the units closer together.
The units are too far apart
Try moving the units farther apart.
The units are too close together
(Error 4) NU is overheating
Make sure that the vents (the small
openings in the plastic housing) on the
units are not blocked. Move the unit to
a cooler area. The system will start
working normally when it cools down.
Make sure that the vents (the small
openings in the plastic housing) on the
units are not blocked. Move the unit to
a cooler area. The system will start
working normally when it cools down.
(Error 3) CU is overheating
Reset the Network Unit by unplug-
ging it and then plugging it back
in. If the problem persists, return
system for service replacement.
(Error 6) NU Hardware Error
Try resetting the Coverage Unit by
unplugging it and then plugging it
back in. If problem persists, return
system for service.
(Error 2) CU Hardware Error
Your unit needs to be registered to
operate. Refer to the Registration Guide
included in your product documents.
(Error 9) New registration required. Run
Phone App or go to www.cel-fi.com/register
Network Unit is too close to a
cellular tower. Move your Network
Unit to another location. Try Moving
the Network Unit to the opposite
side of your Home/Office.
(Error 8) Input signal too strong
(Error 1) Not receiving signal
Relocate the Network Unit to
another room or area where you
have more coverage. (Use your cell
phone to find the best cellular
signal).
Box Contents: • Quick Start Guide • Network Unit • Coverage Unit
• Power Adapters (2) • Mounting Brackets (2)
qsg-PRO-English_16-0211
NEED HELP?
For further instructions, visit:
www.cel-fi.com/support
Cel-Fi™PRO
Quick Start Guide
Otros manuales de Amplificador de CEL-FI
