CEECO SSP-571-D Manual de usuario

SSP-571-D (FORMERLY 579)-ADA-SPK1.07UNVLr1-ISSUE4.0

SERVICE MANUAL

FOR

MODEL SSP-571-D

(FORMERLY MODEL SSP-579-D)

HANDS FREE PANEL TELEPHONE

EQUIPPED WITH SPK1.07 UNVLr1 FIRMWARE

WITH OPTIONAL ADA FEATURE

Serving the Telephone Industry Since 1930

Communication Equipment 519 W South Park Street

& Engineering Company Okeechobee, FL 34972

Voice: 863-357-0798

Fax: 863-357-0006

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

IMPORTANT INFORMATION

FOR

CUSTOMER

Please fill in before you continue.

The following information is necessary when calling CEECO for assistance.

MODEL NUMBER MODEL SSP-571-D-ADA, EQUIPPED

WITH SPK1.07UNVLr1 FIRMWARE

SERIAL NUMBER

DATE MANUFACTURED

LOCATION INSTALLED

For us to better serve you, please have this information available when calling for

technical support.

CEECO

Communication Equipment & Engineering Company

519 W South Park Street

Okeechobee, FL 34972

863-357-0798- telephone

863-357-0006- facsimile

[email protected]

www.ceeco.net

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

TABLE OF CONTENTS

SECTION PAGE

1.0 INTRODUCTION................................................................................................... 4

2.0 GENERAL............................................................................................................... 4

3.0 PROGRAMMING .................................................................................................. 5

PROGRAMMING CONTINUED…..................................................................... 7

4.0 TESTING/OPERATION ....................................................................................... 8

5.0 RECOMMENDED TOOLS AND TEST EQUIPMENT .................................... 8

6.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS ..................... 8

7.0 SPECIFICATIONS............................................................................................... 10

8.0 PARTS LIST ......................................................................................................... 11

9.0 FCC NOTICE........................................................................................................ 12

10.0 REPAIR AND RETURN INFORMATION ....................................................... 13

11.0 WARRANTY POLICY ........................................................................................ 14

12.0 DIAGRAM............................................................................................................. 15

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

1.0 INTRODUCTION

The practices in this manual provide installation and maintenance information for

the CEECO Model SSP-571-D Telephone.

The information in this manual is subject to change without notification.

For information not included in this manual, please call or write:

CEECO

Customer Service

519 W South Park Street

Okeechobee, FL 34972

863-357-0798- telephone

863-357-0006- facsimile

[email protected]

www.ceeco.net

2.0 GENERAL

2.1 The CEECO Model SSP-571-D Hands free telephone is a sturdy, vandal

resistant, Stainless Steel Panel Speakerphone. Instead of a hookswitch and

handset, the SSP-571-D has a Press to start/Press to stop (CALL) button

for the initiation and termination of phone calls.

2.2 The microphone is muted during periods of dial tone to help guard against

the use of hand held dialers.

2.3 Incoming calls may be allowed or blocked depending on the

programming.

2.4 Programming is accomplished via a separately supplied external DTMF

keypad.

2.5 The phone has an optional Braille emergency plate and an optional LED,

which gives a visual indication of the call progress. The LED lights red

when the phone is “off hook”, flashes red and green when ringing, and

turns steady green when the call is answered.

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

3.0 PROGRAMMING

NOTE: It is recommended that you ground yourself to prevent ESD

Damage to the PCB(s).

3.1 Connect the telephone to a working telephone line or a DTMF test set

before programming.

3.2 Locate the multicolor ribbon cable, extending from the Printed Circuit

Board, with a white connector hanging loosely. Locate the programming

keypad (provided separately), which has the mating end of the white

connector attached to it. Connect the keypad to the ribbon cable, by way

of the two connectors.

3.3 Move the mini-jumpers (located on the CEECO-SPK Printed Circuit

Board) to the "ON" position, as depicted on the last page of this manual.

3.4 Press the CALL button and wait for dial tone before programming any

digits.

3.5 It is important to be slow and deliberate when pressing the keys of the

programming keypad. A missed or partial tone could result in improper

programming.

NOTE:Once the “#" (pound) key has been entered you may get an

operator recording or a fast busy, please disregard and continue

programming.

3.6 Press the CALL button located on the front of the phone and utilize the

programming keypad to enter:

#97 #18# #19#

This will clear all user programmable memory, in order to begin.

3.7 Enter # 0 0 followed by a series of ten (10) Digits as selected from the

options on the following page. By entering 0 thru 9 into each of the 10

digits, the phone is customized for the particular installation. A selection

for all ten Digits must be entered in order for the phone to operate

properly.

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

PROGRAMMING CONTINUED…

Digit 1:

0 Always 0 for this model.

Digit 2:

0 No incoming calls allowed.

1 Incoming calls allowed.

Digit 3:

0 No Conversation Time-Out.

1-9 Minutes Conversation Time-Out.

Digit 4:

0 Always 0 for this model.

Digit 5:

0 Always 0 for this model.

Digit 6:

0 No ADA Feature.

9 Activate ADA Feature (9 must be entered to activate the ADA LED light)

Digit 7:

0Always 0 for this model

Digit 8: (PBX Access – see section 3.9)

0 Do not dial PBX access number stored in Location #l8.

1Dial PBX access number stored in Location #18.

Digit 9:

0 Always 0 for this model.

Digit 10:

0 No Wink Detect.

1-9 Length of the Wink (l = 50ms incremental to 450ms – entering a 5 is

recommended).

•Be sure to record your selections below for future reference:

#00 0 __ __ 0 0 __ 0 __ 0 __

1 2 3 4 5 6 7 8 9 10

EXAMPLE:

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

Enter #00 0160000005

Phone will be set as follows:

DIGIT 1 .. ALWAYS 0

DIGIT 2 .. INCOMING CALLS ALLOWED

DIGIT 3 .. 6 MINUTE TIME OUT FOR EMERGENCY CALLS

DIGIT 4 .. ALWAYS 0

DIGIT 5 .. ALWAYS 0

DIGIT 6 .. ADA DEACTIVATED

DIGIT 7 .. ALWAYS 0

DIGIT 8 .. DO NOT DIAL PBX NUMBER STORED IN LOCATION#18

DIGIT 9 .. ALWAYS 0

DIGIT 10 . 250ms WINK

3.8 Enter # 1 9 followed by the desired auto-dial number. When the phone

is in operation and the CALL button is pressed, this auto-dial number will

automatically dial out. This number may be up to eleven (11) digits in

length.

#19 ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___

Example: Enter #195 5 5 1 2 1 2. This will program the phone to

automatically dial the number 555-1212, whenever the CALL button is

pressed.

3.9 If it is necessary for the telephone to automatically dial a PBX access code

or number, enter # 1 8 followed by the desired PBX access code or

number. When the phone is in operation and the CALL button is pressed,

this number will automatically dial out, followed by the auto-dial number.

There will be approximately a one (1) second pause between the dialing of

the two numbers. This number may be up to eleven (11) digits in length.

If this is not a desired feature, proceed to section 3.10.

Example: Enter #189. This will program the phone to automatically

dial the number 9, pause approximately one (1) second, and automatically

dial the auto-dial number, whenever the CALL button is pressed.

#18 ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___

PROGRAMMING CONTINUED…

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

3.10 When programming is finished, return the mini-jumpers to the "OFF"

position. Hang up the phone by pressing the CALL button. The phone is

now ready for Testing/Operation.

4.0 TESTING/OPERATION

4.1 Connect the telephone to a working telephone line.

4.2 To make a call, press the CALL button located on the front of the phone.

When dial tone is received, the transmitter is muted and the phone waits

for numbers to be dialed. The LED will light RED at this time, and the

preprogrammed number(s) will dial out on the line.

4.3 The LED will flash red and green, while the call is ringing.

4.4 When the called party answers the LED will turn GREEN after a

maximum of four seconds, provided the ADA feature was activated (see

section 3.7 Digit 6). Otherwise, the LED will remain RED during off-

hook periods. A normal speakerphone conversation should be allowed.

4.5 When the call is complete, press the CALL button again to hang up. The

LED will go out and the call will be terminated.

4.6 If the user does not press the CALL button when he or she is done, the

phone will hang up after detecting a wink back from the far end, or when

the selected time-out period (see section 3.7 Digit 3) expires.

4.7 Place a call into the phone. If the phone was programmed to allow

incoming calls, answer the phone and the microphone should activate

within approximately three (3) seconds. A normal speakerphone

conversation should follow. If the phone was programmed not to allow

incoming calls, the microphone will not activate.

5.0 RECOMMENDED TOOLS AND TEST EQUIPMENT

DTMF Test Set

Volt/Ohm Meter

3/8" Nut Driver

5/16" Nut Driver

Flat Blade Screw Driver

Security Tool CEECO P/N 301-064

6.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

6.1 Using a 301-064 security tool (sold separately) remove the four security

screws.

6.2 The security tool is for a standard 5/32" button head screw generally used

on the framework of the phone booths.

6.3 Separate the cover assembly from the housing.

6.4 Run the inside station wire through the housing and terminate on to the

RJ11C modular jack, as depicted on the following page. The CEECO-

provided modular jack must be used, as it contains required over-voltage

protection.

6.5 The use of a gas tube or carbon station protector is recommended. The

station ground should not exceed 50 ohms.

6.6 Plug the modular line cord from the SPK 660-000 PC board into the

RJ11C terminal block.

6.7 Dress the line cord away from the security screws and seat the faceplate

into the enclosure.

6.8 Secure the cover assembly by tightening the security screws.

*****WARNING*****

A. Never install telephone wiring during a lightning storm.

B. Never install telephone jacks in wet locations unless the jack

is specifically designed for wet locations.

C. Never touches uninsulated telephone wires or terminals

unless the telephone line has been disconnected at the

network interface.

D. Use caution when installing or modifying telephone lines.

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

6.9 OVER-VOLTAGE PROTECTION DIAGRAM

7.0 SPECIFICATIONS

INPUT POWER: C.O. LINE POWERED

LOOP CURRENT: 30a. MIN. 80ma. MAX.

IMPEDANCE: 600 Ohms

SIGNALING: DTMF, 70ms tone, 50ms spacing

OUTPUT: -4.0 to -6.0dbm

ENVIRONMENTAL: Temperature 0oC to 50oC

Humidity 20%-90% non-condensating.

PROGRAMMING: Via DTMF keypad.

DIMENSIONS: 6.8" W x 9.76" H x 2.75" D

MEMORY RETENTION: Non-volatile memory retention

WEIGHT: 9 Pounds

TYPE JACK: RJ11c

UL LISTED NO.: 6OF5

Otros manuales para SSP-571-D

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Teléfono de CEECO

CEECO

CEECO IP-SSP-511- X Manual de usuario

CEECO

CEECO SSP-560-F Manual de usuario

CEECO

CEECO SSW-321-X Manual de usuario

CEECO

CEECO SSP-511-FD Manual de usuario

CEECO

CEECO SSP-363-E Manual de usuario

CEECO

CEECO BLW-321-F Manual de usuario

CEECO

CEECO SSP-571-D Manual de usuario

CEECO

CEECO WPP-531-D Manual de usuario

CEECO

CEECO MHW-341-Fr1 Manual de usuario

CEECO

CEECO SSP-561-F Manual de usuario

CEECO

CEECO SSP 361-D Manual de usuario

CEECO

CEECO MHW-341-F-106 Manual de usuario

CEECO

CEECO WPP-331-D-M-IVC Manual de usuario

CEECO

CEECO SSP-511-DD-ADA Manual de usuario

CEECO

CEECO SSP-350-X-145 Manual de usuario

CEECO

CEECO WPP-531-FD-ADA-AA-RP Manual de usuario

CEECO

CEECO SSW-321-F-IVC-C-M Manual de usuario

CEECO

CEECO SSP-550-D Manual de usuario

CEECO

CEECO SSW-321-Dr1 Manual de usuario

CEECO

CEECO SSW-321-F Manual de usuario

CEECO

CEECO WPP-531-FD Manual de usuario

CEECO

CEECO SSP-350-X-130 Manual de usuario

CEECO

CEECO SSP-353-F-61 Manual de usuario

CEECO

CEECO WPP-531-D2-ADA-VA-R-SB24VDC Manual de usuario

Manuales populares de Teléfono de otras marcas

GE 2-9480 Manual de usuario

Geemarc

Geemarc PHOTOPHONE 155 Manual de usuario

D-Link

D-Link DWR-720/PW Manual de usuario

Interquartz

Interquartz Gemini IQ333 Manual de usuario

SSS Siedle

SSS Siedle HT 840-0 Manual de usuario

Motorola

Motorola TITANIUM Manual de usuario

Panasonic

Panasonic ICX Manual de usuario

LG H870DS Manual de usuario

Samsung

Samsung GT-I9500 Manual de usuario

AT&T

AT&T Trimline 205 Manual de usuario

Selta

Selta zenyth 600 Manual de usuario

Doro

Doro AFTI 20 Manual de usuario

UNIQCELL

UNIQCELL A1 Manual de usuario

Panasonic

Panasonic KX Series Manual de usuario

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Manual de usuario

BT Decor 425 Manual de usuario

NEC

NEC SV8500 Manual de usuario

Teledex

Teledex PEARL Manual de usuario