CEECO SSP-511-DD-ADA Manual de usuario

WPP-531-DD OR SSP-511-DD-SPK-DD-ADA-R1(1999)-BlackButtons-ISSUE4.0

SERVICE MANUAL

FOR

MODEL WPP(HOB)-531-DD-ADA

WEATHERPROOF TELEPHONE

MODEL SSP-511-DD-ADA

STAINLESS STEEL PANEL TELEPHONE

EQUIPPED WITH SPK-DD-ADA-R1 FIRMWARE

BLACK CALL BUTTONS

Serving the Telephone Industry Since 1930

Communication Equipment 519 West South Park Street

& Engineering Company Okeechobee, FL 34972

Voice: 863-357-0798

Fax: 863-357-0006

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

IMPORTANT INFORMATION

FOR

CUSTOMER

Please fill in before you continue.

The following information is necessary when calling CEECO for assistance.

MODEL NUMBER

MODEL WPP(HOB)-531-DD-ADA OR

SSP-531-DD-ADA EQUIPPED WITH SPK-

DD-ADA-R1 FIRMWARE

SERIAL NUMBER

DATE MANUFACTURED

LOCATION INSTALLED

For us to better serve you, please have this information available when calling for

technical support.

CEECO

Communication Equipment & Engineering Company

519 West South Park Street

Okeechobee, Florida 34972

(863) 357-0798 Voice

(863) 357-0006 Fax

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

TABLE OF CONTENTS

SECTION PAGE

1.0 INTRODUCTION................................................................................................... 4

2.0 GENERAL............................................................................................................... 4

3.0 PROGRAMMING.................................................................................................. 5

PROGRAMMING CONTINUED…..................................................................... 6

3.8 BLACK CALL BUTTON:..................................................................................... 6

3.9 RED EMERGENCY BUTTON: ........................................................................... 6

PROGRAMMING CONTINUED…..................................................................... 7

4.0 OPERATION .......................................................................................................... 7

5.0 RECOMMENDED TOOLS AND TEST EQUIPMENT.................................... 7

6.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS..................... 8

7.0 TESTING................................................................................................................. 9

8.0 SPECIFICATIONS............................................................................................... 10

9.0 PARTS LIST ......................................................................................................... 11

10.0 REPAIR AND RETURN INFORMATION...................................................... 12

11.0 WARRANTY POLICY........................................................................................ 13

12.0 DIAGRAM............................................................................................................ 14

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

1.0 INTRODUCTION

The practices in this manual provide installation and maintenance information for

the CEECO Model WPP 531-DD-ADA Handsfree Weatherproof Telephone or

Model SSP-511-DD-ADA Handsfree Stainless Steel Panel Telephone.

The information in this manual is subject to change without notification.

For information not included in this manual, please call or write:

CEECO

Customer Service

519 West South Park Street

Okeechobee, FL 34972

(863) 357-0798

FAX (863) 357-0006

2.0 GENERAL

2.1 The CEECO Model WPP-531-DD-ADA Handsfree Weatherproof

telephone and Model SSP-511-DD-ADA are sturdy, vandal resistant,

Stainless Steel Panel Speakerphones. The Weatherproof model is

contained in a cast-aluminum, weatherproof housing. Instead of a

hookswitch and handset, they have Black Call Buttons for the automatic

dialing of preprogrammed telephone numbers. The preprogrammed

numbers may be up to eleven digits. The left hand button is the

controlling button. When a call is made with the right hand button, the left

hand button must be pressed to immediately end the call. Otherwise, the

phone will rely on the wink detect (the other party hangs up) or the pre-

programmed timing feature to hang up or reset.

2.2 The phones are equipped with an LED light, which illuminates red during

“off-hook” periods, flashes red and green during dialing, and illuminates

green when the call is answered.

2.2 The microphone is muted during periods of dial tone eliminating the use

of hand held dialers.

2.3 Incoming calls may be allowed or blocked depending on the

programming.

2.4 Programming is accomplished via the DTMF keypad located near the PC

board of the phone.

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

3.0 PROGRAMMING

3.1 Separate the telephone assembly from its mounting or housing by

loosening the four security screws on the stainless steel panel with a

security tool (sold separately) and remove them.

3.2 Connect the telephone to a working telephone line or DTMF test set.

3.3 Locate the two plastic mini-jumpers on the edge of the PC board and

place them in the "ON" position, as depicted on the last page of this

manual.

3.4 Press the LEFT black call button on the front of the panel to begin

programming. You should receive dial tone.

3.5 Each programming location is accessed by dialing the "#" sign and a two

digit code. The valid program locations are #00, #01, and #19. The

previous contents of the location are automatically erased when the

location code is dialed.

3.6 To begin, enter #97 on the keypad to clear all user-programmable

memory.

NOTE: Once the # key has been entered, you may hear a fast busy tone,

an operator recording, or other Central Office signals. Please disregard

these sounds and continue programming, as they will have no effect on the

programming.

3.7 Location "00" is the telephone options program location. By entering 0 or

1 into each of the 5 digits found under location #00 on the next page, the

phone is customized to each particular installation. So after dialing #97,

enter #00 followed by your selections for the five digits. For example,

enter #97#0000101. This entry will set the phone for no incoming calls,

wide dial tone-detection window, time-out disconnect enabled, with a 3

minute time-out. Notice that the dialing is done in a continuous sequence

with no pauses or steps in between.

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

PROGRAMMING CONTINUED…

LOCATION #00

Digit 1:

Always 0. Not used in this model.

Digit 2:

0 No incoming calls allowed.

1 Incoming calls allowed.

Digit 3:

0 Use narrow dial tone detect window.

1 Use wide dial tone detect window.

Digit 4:

0 Time-out disconnect enabled.

1 Time-out disconnect disabled.

Digit 5:

0Time-out of 1.5 minutes.

1Time-out of 3.0 minutes.

*Do not stop your programming sequence yet, however. You must now enter the

numbers to be auto-dialed.

3.8 LEFT BLACK CALL BUTTON

To program the number to be automatically dialed by the left hand call button,

enter # 1 9, followed by the desired number. The number may be up to eleven

(11) digits in length. Example: #1918005551212. When the left button is

pressed, the number 1-800-555-1212 will automatically dial out.

3.9 RIGHT BLACK CALL BUTTON:

To program the number to be automatically dialed by the right hand button, enter

# 0 1 followed by the desired number. The number may be up to eleven (11)

digits in length. Example: #01911. When the right button is pressed, the

number 911 will automatically dial out.

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

PROGRAMMING CONTINUED…

NOTE: A complete programming sequence would appear as follows:

#97#0000101#1918005551212#01911. This would set the phone as stated in the

examples under sections 3.7, 3.8 and 3.9. Again notice that the programming

can be accomplished in one continuous.

3.10 When programming is finished, press the LEFT black call button to hang

up the phone and return the two plastic mini-jumpers to the "OFF"

position, as depicted on the last page of this manual. The phone is now

ready for use.

4.0 OPERATION

4.1 To make a call, press the left or right call located on the front of the phone.

The LED will light red at this time and the preprogrammed number will

dial out. While the phone is ringing, the LED will flash back-and-forth

between red and green. When the called party answers the LED will turn

green after approximately 2-4 seconds. Please note that the ADA feature

will only function on a working telephone line and not on a DTMF test

set. The microphone is active immediately after the preprogrammed

number is released.

4.2 After the call is completed, press the black call button (left) to hang up the

phone. Otherwise the phone will only hang up after detecting the far end

wink back or it times out, if so programmed.

5.0 RECOMMENDED TOOLS AND TEST EQUIPMENT

DTMF test set

Volt/Ohm meter

3/8” Nut Driver

Flat Blade screwdriver

Security Tool (CEECO P/N 301-064)

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

6.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS

6.1 Using a 301-064 security tool (sold separately) loosen and remove the

security screws.

6.2 The security tool is for a standard 5/32" button head screw generally used

on the framework of the phone booths.

6.3 Separate the faceplate assembly from the weatherproof housing or

mounting by pulling the faceplate forward.

6.4 Run the inside station wire into the enclosure and terminate on the RJ1lC

terminal block inside.

6.5 The use of a gas tube station protector is recommended. The station

ground should not exceed 50 ohms.

6.6 Plug the modular line cord from the faceplate assembly into the RJ11C

terminal block.

6.7 If you have not programmed the numbers then they should be entered

now. See section 3.0.

6.8 Dress the line cable away from the security screws and seat the faceplate

into the weatherproof housing or mounting.

6.9 Secure the cover assembly by tightening the security screws.

*****WARNING*****

A. Never install telephone wiring during a lightning storm.

B. Never install telephone jacks in wet locations unless the jack

is specifically designed for wet locations.

C. Never touch uninsulated telephone wires or terminals unless

the telephone line has been disconnected at the network interface.

D. Use caution when installing or modifying telephone lines.

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

7.0 TESTING

Action: Connect the phone to the line.

Press the LEFT black call button.

Reaction: The LED will illuminate red and the preprogrammed number will

automatically dial out. The LED will flash red and green during ringing.

The LED will turn green when the call is answered (within a maximum of

four seconds). A normal speakerphone conversation should take place.

Action: When the call is finished, press the left black call button or wait until

timeout occurs.

Reaction: The call is terminated and the LED will turn off.

Action: Press the RIGHT call button.

Reaction: The LED will illuminate red and the preprogrammed number will

automatically dial out. The LED will flash red and green during ringing.

The LED will turn green when the call is answered (within a maximum of

four seconds). A normal speakerphone conversation should take place.

Action: When the call is finished, press the LEFT black button or wait until

timeout occurs.

Reaction: The call is terminated and the LED will turn off. The phone will return to

an “on-hook” condition, ready for additional calls.

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

8.0 SPECIFICATIONS

INPUT POWER: C.O. Line powered

LOOP CURRENT: 30mA minimum 80 mA maximum

IMPEDANCE: 600 ohms

SIGNALING: DTMF, 70ms tone, 50 ms spacing

OUTPUT: -4.0dbm to -6.0dbm

ENVIRONMENTAL: Temperature 0o C to 50o C

Humidity 20%-90%

PROGRAMMING: Via DTMF keypad.

MEMORY RETENTION: Non-volatile storage (does not require power for

retention).

DIMENSIONS: 7 1/6" Wide x 11 1/4" High x 4 1/4" Deep

(SSP) (Handset on hook)

MOUNTING: Vertical Surface Mount.

WEIGHT: Approximately 4 Pounds.

WEATHERPROOF

HOUSING: Cast Aluminum

DIMENSIONS: 9 ½” Wide x 12 5/8” High x 8” deep.

(WPP) (including door).

MOUNTING: 4 holes spaced 8” x 5 7/8” x 13/32”

(or optional pole mounting bracket)

WEIGHT: Approximately 12 pounds.

UL LISTED NO.: 6OF5

FCC REGISTRATION: BW-88T7-68447-KX-T

TYPE JACK: RJ11C

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Teléfono de CEECO

CEECO

CEECO SSP-363-D Manual de usuario

CEECO

CEECO WPP-331-D-M Manual de usuario

CEECO

CEECO WPL-531-X Manual de usuario

CEECO

CEECO SSP-560-F Manual de usuario

CEECO

CEECO BLW-321-F Manual de usuario

CEECO

CEECO SSP-350-X Manual de usuario

CEECO

CEECO SSP-570-D Manual de usuario

CEECO

CEECO SSP 361-D Manual de usuario

CEECO

CEECO SSP-561-F Manual de usuario

CEECO

CEECO SSP-363-E Manual de usuario

CEECO

CEECO MHW-341-Fr1 Manual de usuario

CEECO

CEECO WPP-331-F Manual de usuario

CEECO

CEECO SSC-303-D Manual de usuario

CEECO

CEECO WPP-531-FD Manual de usuario

CEECO

CEECO WPP-333-D Manual de usuario

CEECO

CEECO SSP-599-F Manual de usuario

CEECO

CEECO SSW-321-FP Manual de usuario

CEECO

CEECO SSP-371-D Manual de usuario

CEECO

CEECO BLC-303-F Manual de usuario

CEECO

CEECO WPP-531-D Manual de usuario

CEECO

CEECO SSP-350-X-130 Manual de usuario

CEECO

CEECO SSP-511-FD Manual de usuario

CEECO

CEECO HOB-313-DD-48 Manual de usuario

CEECO

CEECO SSW-321-F-IVC-C-M Manual de usuario

Manuales populares de Teléfono de otras marcas

GE 2-9480 Manual de usuario

Geemarc

Geemarc PHOTOPHONE 155 Manual de usuario

D-Link

D-Link DWR-720/PW Manual de usuario

Interquartz

Interquartz Gemini IQ333 Manual de usuario

SSS Siedle

SSS Siedle HT 840-0 Manual de usuario

Motorola

Motorola TITANIUM Manual de usuario

Panasonic

Panasonic ICX Manual de usuario

LG H870DS Manual de usuario

Samsung

Samsung GT-I9500 Manual de usuario

AT&T

AT&T Trimline 205 Manual de usuario

Selta

Selta zenyth 600 Manual de usuario

Doro

Doro AFTI 20 Manual de usuario

UNIQCELL

UNIQCELL A1 Manual de usuario

Panasonic

Panasonic KX Series Manual de usuario

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Manual de usuario

BT Decor 425 Manual de usuario

NEC

NEC SV8500 Manual de usuario

Teledex

Teledex PEARL Manual de usuario