Cateye CC-PA100W Manual de usuario

Appendix

SET

CATEYE

PADRONE

CYCLOCOMPUTER

CC-PA100W

• This instruction manual is subject to change

without notice. See our website for the latest

instruction manual (PDF).

• Please visit our website, where a detailed

Quick Start manual containing videos can be

downloaded.

http://www.cateye.com/products/detail/CC-PA100W/manual/

Setting up the

computer

Mounting the

computer

Starting

measurement

Changing settings

Warning/Caution

Product Warranty, etc.

Appendix

SET

Mounting the computer

1 Mount the bracket

• When mounting on stem

• When mounting on handlebar

When mounting the bracket on a handle-

bar, adjust the angle of the bracket so that

the back of the computer faces the speed

sensor when the computer is attached.

Stem

Handlebar

Bracket band

Bracket

Correct Wrong

Bracket rubber pad

Cut

Bracket band

Bracket Dial

Bracket rubber pad Speed sensor

Sensor rubber pad Nylon tie

(x2)

Magnet

Cutting band after mounting

CAUTION:

Cut the bracket band so

that cut end will not cause

injury.

Dial

Appendix

SET

SENSOR ZONE

Max.

70 cm

(27”)

Mounting the computer

2 Mount the speed sensor

Mount the speed sensor in a posi-

tion where the distance from the

computer to the speed sensor is

within the signal range.

3 Mount the magnet

Speed sensor

Cut

Sensor rubber pad

Pull tight

• Mounting on left front fork

• Mounting on right front fork

To sensor zoneSpoke

Magnet

Nylon tie

Appendix

SET

SENSOR ZONE

5 mm

(3/16”)

Mounting the computer

5 Attach/detach computer

6 Test operation

After attaching the computer, rotate the front wheel gently to check that current

speed is displayed on the computer.

If the speed is not displayed, refer to the attachment conditions in steps 1, 2, and 4

again.

4 Adjust the speed sensor and the magnet

The magnet passes through

the speed sensor zone.

The clearance between the

speed sensor and the magnet

is within 5 mm (3/16”).

* The magnet may be mounted at any position on spoke as long as attachment

conditions are satisﬁed.

Hold computer.

Push out so that front lifts up.

Click

Magnet

Sensor zone

Speed sensor

Magnet

Appendix

SET

When using the

computer for the

ﬁrst time, conﬁgure

the initial settings.

MODE

Battery case

cover

Dot section

Short press

Long press

(2 sec.)

1 Clear all data.

Press the AC button on the back of the computer.

* All data is deleted and the computer is reset

to its factory default settings.

2 Select the measurement unit.

Select “km/h” or “mph”.

3 Set tire circumference.

Enter the tire circumference of the front wheel

in mm.

* Refer to “Tire circumference” (page 6).

4 Set the clock.

Each time MODE is pressed and held, settings

switch from time display mode, to hours, to

minutes.

5 Press MENU to complete setup.

Setup is completed and the computer switches to the mea-

surement screen. For instructions on how to start mea-

surement, refer to “Starting measurement” (page 7).

MODE

Setting up the computer

km/h ↔mph

Conﬁrm

Increase

numbers

Move to

next digit

(Press and

hold)

Conﬁrm

Setup complete

Switch item

or increase

numbers

Switch screen

or move to

next digit

(Press and

hold)

Time display mode

MinutesHours

Appendix

SET

ETRTO Tire size

L (mm)

47-203 12x1.75 935

54-203 12x1.95 940

40-254 14x1.50 1020

47-254 14x1.75 1055

40-305 16x1.50 1185

47-305 16x1.75 1195

54-305 16x2.00 1245

28-349 16x1-1/8 1290

37-349 16x1-3/8 1300

32-369 17x1-1/4 (369) 1340

40-355 18x1.50 1340

47-355 18x1.75 1350

32-406 20x1.25 1450

35-406 20x1.35 1460

40-406 20x1.50 1490

47-406 20x1.75 1515

50-406 20x1.95 1565

28-451 20x1-1/8 1545

37-451 20x1-3/8 1615

37-501 22x1-3/8 1770

40-501 22x1-1/2 1785

47-507 24x1.75 1890

50-507 24x2.00 1925

54-507 24x2.125 1965

25-520 24x1(520) 1753

24x3/4 Tubular 1785

28-540 24x1-1/8 1795

32-540 24x1-1/4 1905

25-559 26x1(559) 1913

32-559 26x1.25 1950

37-559 26x1.40 2005

40-559 26x1.50 2010

47-559 26x1.75 2023

50-559 26x1.95 2050

54-559 26x2.10 2068

57-559 26x2.125 2070

58-559 26x2.35 2083

ETRTO Tire size

L (mm)

75-559 26x3.00 2170

28-590 26x1-1/8 1970

37-590 26x1-3/8 2068

37-584 26x1-1/2 2100

650C Tubular 26x7/8

1920

20-571 650x20C 1938

23-571 650x23C 1944

25-571 650x25C 26x1(571) 1952

40-590 650x38A 2125

40-584 650x38B 2105

25-630 27x1(630) 2145

28-630 27x1-1/8 2155

32-630 27x1-1/4 2161

37-630 27x1-3/8 2169

40-584 27.5x1.50 2079

50-584 27.5x1.95 2090

54-584 27.5x2.1 2148

57-584 27.5x2.25 2182

18-622 700x18C 2070

19-622 700x19C 2080

20-622 700x20C 2086

23-622 700x23C 2096

25-622 700x25C 2105

28-622 700x28C 2136

30-622 700x30C 2146

32-622 700x32C 2155

700C Tubular 2130

35-622 700x35C 2168

38-622 700x38C 2180

40-622 700x40C 2200

42-622 700x42C 2224

44-622 700x44C 2235

45-622 700x45C 2242

47-622 700x47C 2268

54-622 29x2.1 2288

56-622 29x2.2 2298

60-622 29x2.3 2326

Setting up the computer

Tire circumference

Tire circumference can be determined by either of the following two methods:

• Measure the actual tire circumference (L)

After ensuring that the tire pressure is appropriate, sit on your

bike, roll it forward so that the tire makes one full revolution (use

the valve or other marking as a reference), and measure the dis-

tance traveled on the road.

• Tire size chart

* The tire size or ETRTO code is indicated on the side of the tire.

L mm

Appendix

SET

MODE

* Av displays .E instead of the measurement value when Tm exceeds approximately

100 hours or Dst exceeds 9999.99 km. Reset the computer.

Switching current function

Pressing MODE switches the current function displayed at the bottom of the screen.

Starting measurement

On the measurement screen, press MENU to go to the menu

screen. Various settings can be changed on the menu screen.

[Measurement screen]

MODE

MODE operation when mounted on bracket

When the computer is mounted on the bracket,

pressing the dot section on the computer

depresses the MODE button.

Current speed

0.0 (4.0) – 99.9 km/h

[0.0 (3.0) – 62.0 mph]

Measurement unit

Current function

Average Speed

0.0 – 99.9 km/h

[0.0 – 62.0 mph]

Maximum Speed

0.0 (4.0) – 99.9 km/h

[0.0 (3.0) – 62.0 mph]

Moving Time

0:00’00” – 99:59’59”

Trip Distance

0.00 – 9999.99 km [miles]

Total distance

0.0 – 99999.9 km [miles]

Clock

0:00 – 23:59 or

1:00 – 12:59

Stopwatch

Turning ON the

stopwatch setting

on the menu screen

adds a stopwatch

to the current func-

tion display.

0:00’00” – 99:59’59”

Appendix

SET

(2 seconds)

MODE

Starting/stopping measurement

Measurement starts automatically when the bicycle

moves.

During measurement the measurement unit (km/h or

mph) ﬂashes.

Resetting data

Pressing MODE for 2 seconds when on the measurement screen

resets all measurement data to 0 (excluding Odo).

Power-saving function

Starting measurement

If the computer does not receive

any signal for 10 minutes, the pow-

er-saving screen is activated and

only the clock is displayed.

If MODE is pressed or a sensor

signal is received while the power-

saving screen is activated, the com-

puter returns to the measurement

screen.

* When the computer is left on

the power-saving screen for 1

hour, the display only shows the

measurement unit. When the

computer is in this state, you can

return to the measurement screen

by pressing MODE.

[Measurement screen]

1 hour

10 minutes

Sleep

Power-saving

screen

Measurement

stops

Measurement

starts

Appendix

SET

Starting measurement [Measurement screen]

Using the stopwatch ( )

You can display a stopwatch that lets you count time regardless of whether measurement

is started or stopped.

To use the stopwatch, set the stopwatch setting on the menu screen to ON.

For instructions on how to set the stopwatch, refer to “Stopwatch” (page 12).

Stopwatch operation

Start/stop Press MODE for 1 second when the stopwatch is

displayed. During counting the icon ﬂashes.

Reset Press MODE for 4 seconds when the stopwatch is

displayed.

* Start, stop, and reset operations of the stopwatch are performed

separately to measurement, and do not affect other measure-

ments.

* The stopwatch continues counting regardless of the power-sav-

ing state. During counting the icon ﬂashes on every screen

except for the menu screen.

Stopwatch

Appendix

SET

Changing settings

Tire circumference

Lets you set the tire circumference.

Clock

Lets you set the clock.

Manual

distance

input

Select

measure-

ment unit

Stopwatch

MODE

Increase

numbers

MODE

Increase

numbers

Measurement

screen Menu screen Description

On the measurement screen, press MENU to go to the menu screen.

Various settings can be changed on the menu screen.

* After changing settings, always press MENU to conﬁrm changes.

* When the menu screen is left on for 1 minute, the computer returns to the measurement screen.

[Menu screen]

Move to

next digit

MODE

(Press and hold)

MODE

(Press and hold)

MODE

(Press and hold)

(Press

and hold)

MODE

12h ↔ 24h

Select display

MODE

Increase

numbers

Set “hours”

MODE

Increase

numbers

Set “minutes”

MODE

(Press and hold)

Change setting

MODE

(Press and hold)

Change setting

Conﬁrm

MODE

Otros manuales para CC-PA100W

Tabla de contenidos

Otros manuales de Accesorios para bicicletas de Cateye

Cateye

Cateye CC-MT400 Manual de usuario

Cateye

Cateye Padrone Smart CC-PA500B Manual de usuario

Cateye

Cateye CC-VL100 Manual de uso y mantenimiento

Cateye

Cateye CC-CD200N Manual de usuario

Cateye

Cateye TR200DW280P Manual de usuario

Cateye

Cateye Rapid mini TL-LD635-R Manual de usuario

Cateye

Cateye OS 1.0 Manual de usuario

Cateye

Cateye Velo Wireless + Manual de usuario

Cateye

Cateye Single Shot Plus HL-EL610RC Manual de usuario

Cateye

Cateye CC-AT200W Manual de usuario

Cateye

Cateye Micro wireless CC-MC200W Manual de usuario

Cateye

Cateye VELO5 Manual de usuario

Cateye

Cateye EL135 Manual de usuario

Cateye

Cateye CC-CD300DW Manual de usuario

Cateye

Cateye CC-VT230W Manual de usuario

Cateye

Cateye V3N Manual de usuario

Cateye

Cateye CC-RD400DW Manual de usuario

Cateye

Cateye CC-TR100 Manual de usuario

Cateye

Cateye CC-MT200 Manual de usuario

Cateye

Cateye CC-ED300 Manual de usuario

Cateye

Cateye CC-ST300 Manual de usuario

Cateye

Cateye CC-RD300W Manual de usuario

Cateye

Cateye Padrone+ Manual de usuario

Cateye

Cateye RAPID X2 KINETIC Manual de usuario

Manuales populares de Accesorios para bicicletas de otras marcas

Sigma

Sigma BC 16.16 Manual de usuario

Playcore

Playcore Dero Setbacks Manual de usuario

VDO Cyclecomputing

VDO Cyclecomputing x3dw Manual de usuario

buratti meccanica

buratti meccanica Clorofilla Trail Manual de usuario

Shimano

Shimano SG-8R20 Instrucciones de funcionamiento

BOB

BOB YAK Manual de usuario

APLIC

APLIC 303303/20190717TW012 Manual de usuario

SRAM

SRAM AXS BlipBox Manual de usuario

Garmin

Garmin EDGE 500 Manual de usuario

Shimano

Shimano FD-RX810 Manual de usuario

KMART

KMART 43115907 Manual de usuario

SIGMA SPORT

SIGMA SPORT Buster 2000 Manual de usuario

NVO Components

NVO Components STEM Manual de usuario

DAXYS

DAXYS BP188 Manual de usuario

XLC

XLC BV-W17 Manual de usuario

Deda Elementi

Deda Elementi SUPERBOX Manual de usuario

Akku Vision

Akku Vision e-bike vision 10046 Guía de inicio rápido

Squire

Squire Inigma Manual de usuario