CastleNet CBV3843Z4S Manual de usuario
Revision 1.0
July 2015
CBV3843Z4S
DOCSIS 3.0 EMTA/Router with
Wireless-AC
Federal Communication Commission Interference
Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. To maintain compliance with FCC RF exposure
compliance requirements, please follow operation instruction as documented in this
manual.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the
antenna.
2) The transmitter module may not be co-located with any other transmitter or
antenna.
As long as 2 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed (for example,
digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions can not be met (for
example certain laptop configurations or co-location with another transmitter), then
the FCC authorization is no longer considered valid and the FCC ID can not be used
on the final product. In these circumstances, the OEM integrator will be responsible
for re-evaluating the end product (including the transmitter) and obtaining a separate
FCC authorization.
CBV3843Z4S Cable Modem
User’s Manual
iii
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end
product which integrates this module.
The users manual for OEM integrators must include the following information in a
prominent location “IMPORTANT NOTE: To comply with FCC RF exposure
compliance requirements. The antenna must not be co-located or operating in
conjunction with any other antenna or transmitter.
FCC Statement
This device complies with Class B Part 15 of the FCC Rules. The device
generates, uses and can radiate radio frequency energy and, if not installed
and used as instructed, may cause harmful interference to radio
communication. Only Coaxial cables are to be used with this device in order to
ensure compliance with FCC emissions limits. Accessories connected to this
device by the user must comply with FCC Class B limits. The manufacturer is
not responsible for any interference which results from use of improper cables,
or which results from unauthorized changes or modifications to the device.
"A Minimum 26 AWG Line Core should be used for connection to the cable
modem"
CBV3843Z4S Cable Modem
User’s Manual
Canada-Industry Canada (IC)
Operation is subject to the following two conditions:
this device may not cause interference and
this device must accept any interference, including interference that may cause
undesired operation of the device.
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment with IC radiation exposure limits set forth for an uncontrolled
environment. To maintain compliance with IC RF exposure compliance requirements,
please follow operation instruction as documented in this manual.
Warranty
Items sold by manufacturer/distributor/agent, hereinafter called "Seller", are
warranted only as follows: Except as noted below Seller will correct, either by
repair or replacement at its option, any defect of material or workmanship
which develops within one year after delivery of the item to the original Buyer
provided that evaluation and inspection by Seller discloses that such defect
developed under normal and proper use. Repaired or replaced items will be
further warranted for the unexpired term of their original warranty. All items
claimed defective must be returned to Seller, transportation charges prepaid,
and will be returned to the Buyer with transportation charges collect unless
evaluation proves the item to be defective and that the Seller is responsible
for the defect. In that case, Seller will return to Buyer with transportation
charge prepaid. Seller may elect to evaluate and repair defective items at the
Buyer's site. Seller may charge Buyer a fee (including travel expenses, if
needed) to cover the cost of evaluation if the evaluation shows that the items
are not defective or that they are defective for reasons beyond the scope of
this warranty.
The Seller makes no warranty concerning components or accessories not
manufactured by it. However, in the event of failure of such a part, Seller will
give reasonable assistance to Buyer in obtaining from the manufacturer
whatever adjustment is reasonable in light of the manufacturer's own warranty.
Seller will not assume expense or liability for repairs made outside the factory
by other than Seller's employees without Seller's written consent.
SELLER IS NOT RESPONSIBLE FOR DAMAGE TO ANY ASSOCIATED
EQUIPMENT, NOR WILL SELLER BE HELD LIABLE FOR INCIDENTAL,
CONSEQUENTIAL, OR OTHER DAMAGES. THIS WARRANTY IS IN LIEU
OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING
THE IMPLIED WARRANTY OF "MERCHANTABILITY" AND "FITNESS FOR
PARTICULAR PURPOSE."
Note to CATV Sysrem Installer
"The EUT must be bonding the screen of the coaxial cable to the earth at the
building entrance per ANSI/NFPA 70, the National Electrical Code (NEC), in
particular Section 820.93, Grounding of Outer Conductive Shield of a Coaxial
Cable.”
Trademarks
All trademarks are the property of their respective owners.
Table of Contents
1.INTRODUCTION ................................................................................................ 1
1.1FEATURES ....................................................................................................... 1
1.2SYSTEM REQUIREMENTS ................................................................................. 1
1.3UNPACKING AND INSPECTION ......................................................................... 1
1.4SAFETY PRECAUTIONS .................................................................................... 2
2.HARDWARE OVERVIEW ................................................................................ 3
2.1FRONT PANEL AND LEDS ............................................................................... 3
3.ETHERNET INSTALLATION .......................................................................... 6
4. WEB MANAGEMENT ........................................................................................... 7
4.1ENTER MODEM'S IP ADDRESS ......................................................................... 7
4.2STATUS ........................................................................................................... 8
4.2.1Software Status.......................................................................................8
4.3BASIC .............................................................................................................. 8
4.3.1DHCP.....................................................................................................8
4.4ADVANCED ..................................................................................................... 9
4.4.1Options...................................................................................................9
4.4.2IP Filtering...........................................................................................10
4.4.3MAC Filtering......................................................................................11
4.4.4Port Filtering.......................................................................................12
4.4.5Forwarding..........................................................................................12
4.4.6Port Triggers........................................................................................13
4.4.7DMZ Host.............................................................................................14
4.5FIREWALL ..................................................................................................... 15
4.5.1Local Log.............................................................................................15
4.6PARENTAL CONTROL .................................................................................... 16
4.7WIRELESS ..................................................................................................... 17
4.7.1Radio....................................................................................................17
4.7.2802.11 Primary Network......................................................................17
4.7.3Access Control.....................................................................................18
4.7.4Advanced..............................................................................................18
4.7.5Bridging ...............................................................................................19
4.7.6WMM....................................................................................................19
4.7.7Guest Network......................................................................................20
4.8MTA ............................................................................................................. 21
4.8.1Status....................................................................................................21
APPENDIX: CABLE MODEM SPECIFICATION ............................................... 22
CBV3843Z4S Cable Modem
User’s Manual
1
1. Introduction
The CBV3843Z4S is a Voice over IP Wireless Residential Gateway
integrated with Cable Modem which allows you implement your VoIP phone
call directly through Cable Modem Broadband Network service with its built-in
PacketCable 1.5 and DOCSIS/EURODOCSIS 2.0 / 3.0 compliant specification.
Equipped with two standard phone ports, CBV3843Z4S could easily provide
end-users low-cost, long-distance calling, faxing, and a host of advanced
service including CBV3843Z4S -to-Phone, Phone-to- CBV3843Z4S
And with the integration of 4 ports switch and IEEE 802.11n wireless
functionality, the CBV3843Z4S could also be used as a Wireless Cable
Modem Residential Gateway in your home or small office. The ability to route
data information into your broadband network could help you easily extend
your local network via wire or wireless.
The CBV3843Z4S is MGCP/SIP compliant and has been tested with most
major VoIP Softswitch vendors’ Call Management systems. And it also has
voice support that includes hardware based Quality of Service (QoS), voice
compression with popular voice CODES G.711, echo cancellation, dynamic
latency (jitter) buffers, silence suppression, and comfort noise generator.
1.1 Features
PacketCable 1.5 standard compliant
DOCSIS /EURODOCSIS 2.0 / 3.0 standard compliant.
Support PacketCable MGCP (Media Gateway Control Protocol)
SIP (Session Initiation Protocol) compliant
4 standard RJ45 connector for GbE Ethernet with auto-negotiation MDIX
functions
Two Rj11 Foreign Exchange Station (FXS) ports for IP telephony
QoS enhancement
MSO SNMPv3 remote network management
Provide MIBs DOCSIS 1.0/1.1/2.0/3.0
Support simultaneous voice and data communications
Echo Cancellation
Voice Active Detection (VAD)
Comfort Noise Generation (CNG)
Web Browser Management auto detect network status
Build-in IEEE802.11AC as AP
1.2 System Requirements
IBM Compatible, Macintosh or other workstation supports TCP/IP
protocol.
An Ethernet port supports GbE Ethernet connection.
Subscribed to a Cable Television company for Cable Modem services.
1.3 Unpacking and Inspection
Included in the kit is the following:
1 x EMTA CBV3843Z4S
CBV3843Z4S Cable Modem
User’s Manual
2
1 x Quick Installation Guide
1 x RJ-45 CAT 5 Cable
1 x 12V/2.5A Power Supply Adaptor
1 x 6P4C Telephone Cord
If any of above items lost or damaged, please contact your retailer or ISP for
assistance.
1.4 Safety Precautions
For your protection, observe the following safety precautions when setting up
and using your equipment. Failure to observe these precautions can result in
serious personal injury and damage to your equipment.
Make sure the voltages and frequency of the power outlet matches the
electrical rating labels on the AC Adapter.
Do not place any object on top of the device or force it into a confined
space.
Never push objects of any kind through openings in the casing.
Dangerous voltages may be present. Conductive foreign objects could
produce a short circuit that could cause fire, electrical shock, or damage
to the equipment.
Whenever there is danger of lightning, disconnect the power cable and
the Hybrid-Fiber Coax cable from the cable modem to prevent damage to
the unit. The use of an AC protection device will not completely protect
the cable modem product from damage caused from the transmission
across the Hybrid-Fiber Coax network.
CBV3843Z4S Cable Modem
User’s Manual
3
2. Hardware Overview
2.1 Front Panel and LEDs
There are ten Light-Emitting-Diodes (LEDs) located on the
front panel top provide status information to the user.
NAME COLOR MODE STATUS
PWR Green On DC Power is connected
Off No DC Power connected
DS
Green
Blinking Downstream scanning
On Downstream locked
Off Cable interface idle or W/DS bonding
Orange On W/DS locked
Off W/DS disabled
US
Green
Blinking Upstream scanning
On Upstream locked
Off Cable interface idle or W/US bonding
Orange On W/US locked
Off W/US disabled
ONLINE Green
Blinking CM provisioning
On CM On-line
Off CM Off-line
LAN
Green
Blinking Data in traffic
On ETH device connected (GbE mode)
Off No ETH device connected
Orange Blinking Data in traffic
On ETH device connected (FE mode)
CBV3843Z4S Cable Modem
User’s Manual
4
Off No ETH device connected
WLAN
2.4GHz &
5G
Green
On WiFi enable
Off WiFi disable
Blinking Data in traffic
Blinking WPS in paring
ON WPS enabled
Off WPS disabled
On TEL1 on-hook
Off TEL1 disable
blinking TEL1 provisioning or off-hook
On TEL2 on-hook
Off TEL2 disable
blinking TEL2 provisioning or off-hook
2.2 Rear Panel and Hardware Connection
This chapter describes the proper steps for connecting your cable modem.
Please be sure to follow the steps in the sequence outlined below. Failure to
do so could result in improper operation or failure of your cable modem.
Step 1:
Connect a cable by feeding the F-connector on the back of the cable modem.
Ensure the center conductor of the 75 ohm coaxial cable is inserted directly
into the center of the F-connector. Secure the coaxial cable by carefully
threading the outer shell of the coaxial cable connector onto the F-connector
in a clockwise direction until tight. Be careful not to over-tighten the connector
or you may damage either the connector or the cable modem.
Step 1 Connecting
the Coaxial Cable
Step 3 Connecting the
Telephone cord
Step 4
Connecting to the
AC Adapter Step 2 Connecting to a
Network Interface Card
Power On
/ Off
Tabla de contenidos
Otros manuales de Módem de CastleNet
Manuales populares de Módem de otras marcas
US Robotics
US Robotics 3453C Manual de usuario
MaxTech
MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario
Zte
Zte MF823 Manual de usuario
Four-Faith
Four-Faith F1403 Manual de usuario
Sierra Wireless
Sierra Wireless AIRLINK MP595W Manual de usuario
Gemtek
Gemtek WiMAX WIXFBR-103 Manual de usuario