Casio Exilim EX-FH25 Manual de usuario

CAS|O

Digital Camera

EX-FH25

User's Guide

Thank you for purchasing this CASIO product.

• Before using it, be sure to read the precautions contained in this User's Guide.

• Keep the User's Guide in a safe place for future reference.

• For the most up-to-date information about this product, visit the official EXlLIM

Website at http:!/www.exilim.com/

• Multi-motion will not operate correctly if you shake or move the camera along with

the movement of the subject.

• If an error message appears on the monitor screen, either secure the camera so it

does not move or shoot against a different type of background.

• If not enough CS images are recorded, an error will be displayed before the

camera starts to place the isolated subject onto the stationary background. This

can be caused if you release the shutter button too soon when recording the

moving subject. Keep the shutter button fully depressed long enough to allow

recording of more images.

• Choose a shooting angle so the colors, shapes, and patterns of the moving subject

and the background are as different as possible.

• Avoid a shooting angle where the background is monotone or mono-pattern (such

as a clear blue sky).

• The camera may not be able to compose the final image if the intervals between

movements are so narrow the subject shots overlap. If this happens, increase the

interval by using the control panel to select a slower "High Speed CS fps" setting

(page 60).

With High Speed Best Selection, the camera automatically shoots a series of images,

and selects the best one based on facial image blur, and facial expression (whether

the subject is smiling or blinking).

1. In the REC mode, press [BS].

2. Select "High Speed Best Selection" and then press [SET].

3. Press the shutter button to shoot.

• This will cause the message "Busy... Please wait..." to appear. Do not move

the camera while this message is displayed. The recording process takes

some time to complete after the message appears.

82 Using BEST SHOT

_NOTE

• The current mode dial setting is ignored when recording with this BEST SHOT

scene.

• With this BEST SHOT scene, the flash setting automatically becomes [] (Flash

Off).

• Shooting with this BEST SHOT scene makes the shooting range narrower than

normal.

• The triple Self-timer cannot be used with this BEST SHOT scene.

• This BEST SHOT scene saves only a single final image.

• If one or more of the faces are blurred in all of the images that are shot, they will be

blurred in the final image as well.

• The following conditions may make it impossible for the camera to determine if the

subject is blinking or smiling. This may result in a final image in which the subject is

blinking or not smiling.

- Faces that are partially or completely darkened by shadows, etc.

- Hair that is hiding or near the eyes

- Eye glasses

- Small faces

- Faces that are not looking directly at the camera

• Shooting a large group of people will cause processing of the image after shooting

to take longer.

You can use these features to shoot an image automatically whenever the subject

moves into or moves out of a frame on the monitor screen. You also can configure the

camera to record images of what happened immediately before and after the subject

moves.

Automatically records what happened immediately before and

after the subject moves outside of a boundary on the monitor

screen.

Automatically records what happened immediately before and

after the subject moves into a boundary on the monitor screen.

83 Using BEST SHOT

•To setup the camera

1. In the REC mode, press [BS].

2. Select "Move Out CS" or "Move In CS" and then press [SET].

3. Press [SET].

4. Configure the boundary location and size

settings.

Movesthe boundary.

Resizesthe boundary.

.Press [SET].

•If you want to reconfigure the settings, start again

from step 3.

6. Press [V].

7. Use [A] and [V] to select the third control panel option from the

bottom (High Speed CS fps).

8. Use [,] and [_.] to select the continuous shutter cs speed

(CS) speed you want and then press [SET].

Boundary

Enables specification of the number of

CS images recorded per second.

9. Use [A] and [V] to select the second control

panel option from the bottom (Max CS shots).

10. Use [,] and [,] to select the maximum number of shots for each

continuous shutter operation and then press [SET].

11.Use[A] and [V] to select the bottom control panel option (Prerecord

CS shots).

84 Using BEST SHOT

12.Use[,] and [_.] to specify how many of the 30 images and for how

long images should be pre-recorded in the buffer.

• You cannot set a value of "0" for the number of Prerecord CS buffer images.

Shutter button full-press

Number of remaining images

images and pre-record and remaining recording time

time after the shutter button full-press

13.Press [SET].

• The approximate number of recordable

CS images will appear on the monitor

screen.

Number of recordable CS--_

images F_

Remaining snapshot

memory capacity

14.Use [A] and [V] to select the fourth control panel option from the

bottom (Trigger Sense).

15. Use [,] and [,] to select the subject movement sensitivity, and then

press [SET].

• You can select any one of three sensitivity levels: "High", "Normal", or "Low".

• Move Out CS Setting Guide

High : For a subject that moves out of the boundary quickly

Low : For a subject that moves out of the boundary slowly

• Move In CS Setting Guide

High : For a subject that moves into the boundary quickly or for a small subject

(relative to the boundary)

Low : For a subject that moves into the boundary slowly or for a large subject

(relative to the boundary)

• To shoot using Move Out CS

1. Compose the image so the subject is within the boundary on the

monitor screen.

2. Half-press the shutter button.

• The camera will adjust exposure and focus automatically.

85 Using BEST SHOT

3. When the boundary on the monitor screen turns

green, press the shutter button the rest of the

way down.

At this time the camera will go into recording standby

and start pre-recording images and storing them in a

buffer, in accordance with the Prerecord CS shots

setting you configured in step 11 under "To setup the

camera" on page 84. After the buffer becomes full, new images keep being added

while older images are continually being deleted.

The camera will start saving images automatically the moment it detects that the

subject has moved out of the boundary.

• "Q AUTO" flashes on the monitor screen during recording standby and auto

recording.

4. Image recording will continue until the end of the recording time is

reached.

• While the camera is in Move Out CS recording standby, you can cancel

standby by pressing the shutter button all the way down. You then will be able

to shoot images normally.

• To stop an ongoing real-time recording operation, press [SET].

5. Save the CS images (page 62).

•To shoot using Move In CS

1. Compose the image at a location where you expect the subject to enter

the boundary on the monitor screen.

.Half-press the shutter button.

• The camera will adjust exposure and focus automatically.

• In this case, use of manual focus (page 53) to preset a fixed focus is

recommended.

86 Using BEST SHOT

3. When the boundary on the monitor screen turns

green, press the shutter button the rest of the

way down.

At this time the camera will go into recording standby

and start pre-recording images and storing them in a

buffer, in accordance with the Prerecord CS shots

setting you configured in step 11 under "To setup the

camera" on page 84. After the buffer becomes full, new

images keep being added while older images are

continually being deleted.

The camera will start saving images to memory automatically the moment it

detects the subject has moved into the area within the boundary.

• "Q AUTO" flashes on the monitor screen during recording standby and auto

recording.

Boundary

4. Image recording will continue until the end of the recording time is

reached.

• While the camera is in Move In CS recording standby, you can cancel standby

by pressing the shutter button all the way down. You then will be able to shoot

images normally.

• To stop an ongoing real-time recording operation, press [SET].

5. Save the CS images (page 62).

_NOTE

• Compose the image so the entire subject and its background are within the

boundary. Recording may not be performed correctly if there is little difference

between the subject and the part of the background enclosed by the boundary.

Also, Move Out CS may not record correctly if the subject is not in the center of the

boundary.

• Move In CS and Move Out CS do not operate correctly if you press the shutter

button all the way down. Be sure to half-press the shutter button. After images are

pre-recorded, press the shutter button the rest of the way down.

• After pressing the shutter button all the way to put the camera into record standby,

keep the camera still. Recording may not be performed correctly if you move the

camera during record standby.

• The current mode dial settings are ignored when shooting with this BEST SHOT

scene.

87 Using BEST SHOT

• The sleep mode and Auto Power Off are disabled while the camera is in record

standby.

• The camera may not start recording automatically or camera power may turn off

when battery power is low. Always make sure that the batteries are sufficiently

charged or use the optional AC adaptor before using these features.

• To save all of the continuous shutter images, select "Save All" (page 62) as the

continuous shutter image save method. If you do, make sure that the memory card

loaded in the camera has enough free space to store them.

• Zoom is disabled, and focus and exposure are fixed while the camera is in

recording standby.

• The Self-timer cannot be used with this BEST SHOT scene.

The High Speed CS capabilities provide you with a variety of BEST SHOT options to

suite exactly the type of image you are trying to record. Images continue to be shot as

long as you keep the shutter button depressed, with the shooting speed optimized

according to the BEST SHOT scene you are using.

Prerecord CS (page 58) pre-records images when you half-press the shutter button.

Then when you press the shutter button the rest of the way down, the camera stores

what is currently in the buffer and starts real-time continuous shutter shooting of new

images. Shooting continues until you release the shutter button or until a total of up to

30 images (buffer images plus new images) are shot. Some of the 30 images are of

action that occurred before you full-pressed the shutter button and some are after.

This helps to ensure you capture exactly the moment you want, even if your timing is

slightly off.

Shutter button half-press Shutter button full-press Shutter button release

I I

Pre-recorded images Continuous recording of images until shutter

button released_

You can record up to 30 images (pre-recorded buffer images plus real-time images) for

each Prerecord CS operation.

88 Using BEST SHOT

1. In the REC mode, press [BS].

2. Select the BEST SHOT scene you want to use and then press [SET].

The following are the settings for each BEST SHOT scene.

Expression CS 3 fps 10 (3.3 seconds) 3 (1 second)

Baby CS 5 fps 10 (2 seconds) 3 (0.6 seconds)

Child CS 10 fps 20 (2 seconds) 5 (0.5 seconds)

Pet CS 15 fps 30 (2 seconds) 5 (0.3 seconds)

Sports CS 30 fps 30 (1 second) 10 (0.3 seconds)

You can change the above settings if you want. See page 58 for details.

Selecting one of these BEST SHOT scenes will enable High Speed CS as the

initial default. Though you could change the CS setting to Normal Speed CS, it

is recommended that you leave it set as High Speed CS.

3. Half-press and hold the shutter button to start pre-recording of images.

A preset number of images are pre-recorded. The pre-recorded images are

continually updated until you full-press the shutter button.

• If you release the half-pressed shutter button before pressing it the rest of the

way down, all of the pre-recorded images currently in the buffer will be deleted.

• The camera will not emit shutter sounds as it pre-records images.

.Press the shutter button the rest of the way down.

This will save the pre-recorded images and start shooting new images in real-

time. Images continue to be shot as long as you keep the shutter button

depressed.

5. Shooting will stop when you release the shutter button or after the

maximum number of shots is reached.

6. Save the CS images (page 62).

89 Using BEST SHOT

_NOTE

• Except for [] (Flash CS), the current mode dial setting is ignored and the camera

enters the CS mode when shooting with these BEST SHOT scenes. The Flash CS

mode is enabled only when the mode dial is set to [] (Flash CS). In this case, the

camera uses the "Flash CS fps" and "Flash CS Images" settings that were

configured for the Flash CS settings before the BEST SHOT scene was selected

(page 56). Note, however, that the A, S, and M exposure modes cannot be used.

• The current "CS" setting ("High Speed CS" or "Normal Speed CS") is applied.

Precautions and control panel operations are the same as those that apply to High

Speed CS (page 58) and Normal Speed CS (page 57).

• When using High Speed CS, Prerecord CS (pre-recording of images before the

shutter button is full-pressed) is not performed if you full-press the shutter button

without half-pressing first. Whenever possible, be sure to half-press the shutter

button, compose the image, and then full-press the shutter button.

The High Speed Movie capabilities of the camera provide you with a variety of BEST

SHOT options to suite exactly the type of image you are trying to record.

1. In the REC mode, press [BS].

2. Select the BEST SHOT scene you want to use and then press [SET].

Child High Speed Movie 120 fps

Pet High Speed Movie 240 fps

Sports High Speed Movie 420 fps

• You also can change the frame rate, if you want (page 68).

90 Using BEST SHOT

Otros manuales para Exilim EX-FH25

Tabla de contenidos

Otros manuales de Cámara digital de Casio

Casio

Casio Exilim EX-Z60 Guía de solución de problemas

Casio

Casio EXILIM EX-ZR15 Manual de usuario

Casio

Casio EX-FC100BK Manual de usuario

Casio

Casio Exilim EX-H30 Manual de usuario

Casio

Casio Exilim EX-ZR1000 Manual de usuario

Casio

Casio EX-Z270 - EXILIM Digital Camera Manual de usuario

Casio

Casio QV-R80 Manual de usuario

Casio

Casio Exilim EX-TR15 Manual de usuario

Casio

Casio GZE-1 Manual de usuario

Casio

Casio QV-4000 Manual de usuario

Casio

Casio YC-400 - 2 Manual de usuario

Casio

Casio EXILIM K1190PCM1DMX Manual de usuario

Casio

Casio QV-770 Manual de usuario

Casio

Casio Exilim EX-Z3000 Manual de usuario

Casio

Casio QV-10C Instrucciones de instalación y mantenimiento

Casio

Casio QV-R3 Manual de usuario

Casio

Casio QV-5500SX Manual de usuario

Casio

Casio EX-S2 - Exilim 2MP Digital Camera Manual de usuario

Casio

Casio Exilim EX-Z29 Manual de usuario

Casio

Casio EX-Z450 - EXILIM Digital Camera Manual de usuario

Casio

Casio Exilim EX-ZS160 Manual de usuario

Casio

Casio QV-70 Manual de usuario

Casio

Casio EXILIM EX-FC300S Manual de usuario

Casio

Casio EX-FR10 Manual de usuario

Manuales populares de Cámara digital de otras marcas

Mercury

Mercury 350K Manual de usuario

Pentax

Pentax Optio LS 465 Manual de usuario

Sanyo

Sanyo VPC-S1085 Manual de usuario

GE SMART A1255 Manual de usuario

Point Grey

Point Grey Gazelle Manual de usuario

Nikon

Nikon COOLPIX A Manual de usuario

Pentax

Pentax P-5 Manual de usuario

BlazeVideo

BlazeVideo A280 Manual de usuario

Sony

Sony MCA-20 Manual de usuario

Sony

Sony Alpha DSLR-A290 Manual de usuario

ATIK Cameras

ATIK Cameras One Manual de usuario

CohuHD Costar

CohuHD Costar 3930 Series Manual de usuario

Leica

Leica M10-R Manual de usuario

FujiFilm

FujiFilm FinePix A700 Manual de usuario

Lorex

Lorex LNZ81P25 Series Manual de usuario

GE J1470S Manual de usuario

Sony

Sony A6700 Guía del usuario

Canon

Canon EOS ELAN7 Manual de usuario