Cascade K Series Manual de usuario
SER MANUAL
U
用户手册
K系列调距叉
K-Series Fork Positioners
官 方 微 信 号 天 猫 旗 舰 店
服 务 热 线
c
目录 ONTENTS
C
介绍 INTRODUCTION 1
操作 OPERATION 2
对叉车的要求 TRUCK REQUIIREMENTS 7
液压供油系统 HYDRAULIC SUPPLY 9
安装 INSTALLATION 10
定期维护保养 PERIODIC MAINTENANCE 21
备件 PARTS 24
质量保证政策 WARRANTY 26
介绍 NTRODUCTION
I
这本用户手册适用于卡斯卡特K系列调距叉，包括操作指南，安装说
明，定期维护保养和零件明细等内容。所有参数均同时以英制和公
制作为标注。
重要提示：
重要提示：
K系列调距叉采用公制设计，管路连接是可能视需要采用
过渡转换接头。
特殊定义
特殊定义
本手册含有一些特色的提示，操作前务必仔细阅读所有的“警告”和“
注意”。“重要提示”和“备注”则作为具有特定意义或简化工作的信息提
供。
警告：
警告：
叉车/属具的综合承载能力有叉车制造商决定，可能比属具铭牌所标注的数值来得低。
警告：
警告：
非得到许可的专业人员不得操作属具。
警告：
警告：
所示内容必须切实牢记，以免造成人身伤害。
WARNING:Rated capacity of the truck/attachment Combination is a responsibility of the original truck Manufacturer and
may be less than shown on the attachment Nameplate. Consult the truck nameplate.
WARNING:Do not operate the attachment unless you are a trained and authorized lift truck driver.
WARNING:A statement preceded by WARNING is information that should be acted upon to prevent bodily injury. A
WARNING is always inside a ruled box.
注意：此类标识的内容必须遵守，以免造成设备损坏。
重要提示： 这种提示包含特定信息。
备注：这种标识所含信息使工作简化。
CAUTION:A statement preceded by CAUTION is information that should
be acted upon to prevent machine damage.
IMPORTANT-A statement preceded by IMPORTANT is information that
possesses special significance.
NOTE: A statement preceded by NOTE is information that is handy to
know and may make the job easier.
This User Manual is for Cascade K-Series Fork
Positioner/Sideshifter. It contains an Operation Guide, Instal-
lation Instructions, Periodic Maintenance and Parts Manual.
All specifications are shown in Imperial and (Metric) units
where applicable.
IMPORTANT:K-Series Fork Positioner/Sideshifter is metric.
Supply fittings adapted as required for application.
Special Definitions
The statements shown appear throughout this Manual where
special emphasis is required. Read all WARNINGS and
CAUTIONS before proceeding with any work. Statements
labled IMPORTANT and NOTE are provided as additional
information of special significance or to make the job eaiser.
- 1 -
操作 PERATION
O
这个章节包含了卡斯卡特K系列调距叉操作指南。旨在帮助
避免操作中损伤属具及货物。
这些信息旨在使操作者更容易掌握如何高效安全地使用和操
作调距叉。在操作前请仔细阅读本手册，掌握所有的操作步
骤及安全规则，不详之处请向您的上级请教。
安全第一！
安全第一！
大多数的事故都起因于操作或判断失误，请格外
留心维护保养状况差和工况恶劣的属具并及时加以解决。
This section contains operating instructions for Cascade
K-Series Fork Positioner/Sideshifter. It will help you avoid
common errors which often cause damage to the equipment
or product being handled.
This information is intended to simplify operator understand-
ing about effective and safe Fork Positioner/Sideshifter use
and operation. Read this information thoroughly before
operating the Attachment. Be sure you know and under-
stand all operating procedures and safety precautions. If
you have any questions or don’t understand a procedure,
ask your supervisor.
Emphasize Safety! Most accidents are caused by operator
carelessness or misjudgement. You must watch for poorly
maintained equipment and hazardous situations and correct
them.
侧移器框架
Sideshifter
上钩
Upper Hooks
下钩
Lower Hooks
油缸
Cylinder
货叉
Forks
挡货架
Backrest
- 2 -
操作 PERATION
O
PP
禁止载人行驶
No riders
禁止伸手穿越门架
No reaching through mast
关闭发动机，制动，降下货叉
Motor off, park, lower load
空载行驶
Traveling empty
提升
Raise
10厘米
10 cm 空载时
No load
负载时
with load
上下坡
Ramps
在装载时前后倾
Tilt when
traveling loaded
禁止货叉下站人
No standing under load
- 3 -
操作 PERATION
O
P
禁止坡上停车
No parking on ramp
禁止坡上转弯
No turning on ramp
注意行驶空间
Watch clearances
交通标志
TRAFFIC
工作人员
Workers
停止
Stop
观察 Observe
湿地板
Wet floor
STOP
凸起
Bumps
凹坑
Dips
双向行驶时必须慢行
Slow for two-way traffic
十字路口处鸣笛，慢行
Sound horn, slow at
intersection
转弯时必须鸣笛，慢行
Sound horn, slow at
corner
- 4 -
操作 PERATION
O
WEIGHT
货物举高时应限速侧移
Limit sideshift operation with
raised load.
货物举高时应限速行驶
Limit truck movement with
raised load.
货物重量不能超过叉车/属具组合承载能力
Load weight must not exceed combined Truck/at-
tachment capacity(see truck namaplate)
左右货叉总承载能力必须大于货物重量
Total fork capacity(LH+RH fork) must be greater
than load weight. Check capacity stamp on forks.
小心：不能用单个货叉挑货物
CAUTION:Do not put side loads
on forks
举升货物后再侧移
Raise load prior to sideshifting
调距叉/侧移器操作
调距叉/侧移器操作
Fork Positioner/Sideshifter Operation
行驶前将货物居中
Center load prior to
traveling
货物顶部不能超过挡货架上端
Top of load should not extend
above backrests.
- 5 -
操作 PERATION
O
下降
Hoist Down
前倾
Tilt Forward
上升
Hoist Up
后倾
Tilt Back
B
D
C
CD
A
AB
BA
B
A
多路阀功能
多路阀功能
AUXILIARY VALVE FUNCTIONS
GA0005.eps
FP9606.eps
FP9606.eps
AC
BD
侧移/调距动作时
A 左侧移
B 右侧移
C 张开货叉
D 并拢货叉
SIDESHIFTING/FORK
POSITIONING
A Sideshift Left
B Sideshift Right
C Open/Spread Forks
D Close forks
调距动作时带电磁阀
A 左侧移
A 张开货叉（按手柄按钮）
B 右侧移
B 并拢货叉（按手柄按钮）
SIDESHIFTING/FORK POSITIONING
WITH SOLENOID VALVE
A Sideshift Left
A Spread Forks(press knob button)
B Sideshift Right
B Close forks(press knob button)
- 6 -
对叉车的要求 RUCK REQUIREMENTS
T
GA0028.eps
GA0131.eps
A
叉车供油压力设置 Truck Relief Setting
推荐压力值：105bar(2200psi)
最大值：240bar(3500psi)
叉车流量 Truck Flow Volume
最小Min.① 最大Max.②
最小 Minimum 最大 Maximum
推荐Rec.
55K,65K,
X55K,X65K
4LPM
(1GPM)
12LPM
(3GPM)
7.5LPM
(2GPM)
100K 4LPM
(1GPM)
20LPM
(5GPM)
16LPM
(4GPM)
①卡斯卡特K系列侧移式调距叉
兼容SAE 10W油基液压油（符合
Mil.规格）。MIL-0-5606或
MIL-0-2104B标准）。不推荐合
成或水基液压油。若需要采用阻
燃型液压油则必须采用特殊密封
件。详情请联系卡斯卡特。
②若流量低于推荐值，会造成调
距速度缓慢。
③若流量超过最大值，会造成过
热，降低系统性能同时缩短液压
系统寿命。
①Cascade K-Series Fork Positioner/Sideshifters
are compatible with SAE 10W petroleum base
hydraulic fluid meeting Mil. Spec. MIL-0-5606 or
MIL-0-2104B. Use of synthetic or aqueous base
hydraulic fluid is not recommended. If fire resistant
hydraulic fluid is required,special seals must be
used.Contact Cascade.
②Flow less than recommended will result in slow
fork positioning speed.
③Flow greater than maximum can result in exces-
sive heating, reducing system performance and
shortening hydraulic system life.
货叉架安装等级尺寸（
货叉架安装等级尺寸（A）
Carriage Mount Dimension(A) ITA(ISO)
Class II
Class III
380.0(14.94 in.)
474.5(18.68 in.)
381.0(15.00 in.)
476.5(18.74 in.)
货叉架-
货叉架-
清理和检查货叉架，确保横梁是
平行的而且端部是平直的。将所有焊接突
出部位打磨光滑以免影响侧移器的下滑块
。修补所有破损的凹坑。
Carriage-Clean and inspect carriage
bars.Assure that bars are parallel and that
ends are flush. Grind smooth any protrud-
ing welds that may affect Sideshifter lower
bearing. Repair any damaged notches.
- 7 -
对叉车的要求 RUCK REQUIREMENTS
T
前倾
Tilt Forward
左侧移
Sideshift
Left
张开货叉
Spread Forks
并拢货叉
Close Forks
右侧移
Sideshift Right
上升
Hoist Up后倾
Tilt Back
多路阀功能
多路阀功能
确保符合ITA(ISO)标准
Auxiliary Valve Functions
Check for compliance with ITA(ISO) standards
GA0082.eps
下降
Hoist Down
- 8 -
Otros manuales para K Series
2
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Idiomas:
Otros manuales de Máquina elevadora de Cascade
Cascade
Cascade 80R Manual de usuario
Cascade
Cascade KOOI ROLLERFORKS Manual de usuario
Cascade
Cascade KOOI Reachforks 20B TFT Manual de usuario
Cascade
Cascade J Series Manual de usuario
Cascade
Cascade C Series Manual de usuario
Cascade
Cascade E Series Manual de usuario
Cascade
Cascade UTF2-08-1004-1885315 Manual de usuario
Cascade
Cascade E Series Manual
Cascade
Cascade G Series Manual
Cascade
Cascade F Series Manual de usuario
Cascade
Cascade Turnafork E Series Manual de usuario
Cascade
Cascade K Series Manual de usuario
Cascade
Cascade iForks Manual de usuario
Cascade
Cascade G Series Manual de usuario
Cascade
Cascade D Series Manual
Cascade
Cascade Viewmast II 30C Triple Manual de usuario
Cascade
Cascade K Series Manual de usuario
Cascade
Cascade N Series Manual de usuario
Cascade
Cascade F Series Manual de usuario
Cascade
Cascade C Series Manual de usuario
