CAS CI-6000A Series Manual de usuario

Contents

1. Introduction......................................................................... 4

2. Features................................................................................ 6

3. Technical Specification...................................................... 7

4. Measure of Appearance.................................................... 9

5. Front Panel ........................................................................ 10

6. Rear Panel ......................................................................... 14

7. How to Install.................................................................... 15

8. Calibration Mode............................................................. 16

9. Set Mode ............................................................................ 24

10. Test Mode......................................................................... 43

11. Weighing Mode............................................................... 47

12. Serial Interface(COM1, COM2) ................................ 63

13. Options ............................................................................. 67

1. Introduction

Thank you for purchasing the CAS CI-6000A weighing indicator.

We have designed this equipment with many advanced features, high quality construction, and user-

friendly menu driven programming.

CAS indicator is shaped firmly and delicately designed to coincide with the special requirements of

several industrial fields and includes many functions and various external interfaces. Also, it contains

help display functions to be used easily.

Before using CI-6000A, It is recommended to read this manual carefully and to apply

the function application fully.

Precautions

Observe the following safety precautions :

Warning

When any damage or defect

occurs, contact your CAS

authorized dealer immediately

for proper repair.

Insert plug firmly to wall outlet to

prevent electric shock.

Scale must be grounded to

minimize electricity static. This

will minimize defect or electric

shock.

Do not pull the plug by its cord

when unplugging. Damaged

cord could cause electric shock

or fire.

To prevent from fire occurring,

Do not place or use the scale

near flammable or corrosive

gas.

To reduce electric shock or

incorrect reading, Do not spill

water on the scale or place it in

humid condition.

Avoid placing the scale near

heather or in direct sunlight.

Attention

For consistent and accurate

reading, maintain periodical

check by your CAS authorized

dealer.

Avoid sudden shock to the scale.

Internal mechanism could by

damaged.

Attach the rubber pad to the

bottom of the indicator.

Elimination is possible.

Place the scale on firm and

temperature consistent

environment.

Keep the scale away from the electromagnetic generation devices.

This may interfere with accurate reading.

Our Dealers :

CAS feels that each of its valued customers should get the best service

available.

Whether it’s the initial installation of our product, maintenance/repair work, or simply answering

questions about our products, CAS Corporation and all of its Authorized Dealers are highly trained to

assist you with any need regarding CAS products.

2. Features

1) Features

■High speed, High accuracy

■The adoption of high speed micro processor

■A/D conversion speed : Maximum 200 times/sec

■Appropriate for weighing and measurement system

■Easy operation and various options

■Simple and prompt Full Digital Calibration

(SPAC

TM : Single pass automatic span calibration)

■RFI/EMI screened

■WATCHDOG circuitry (System restoration)

■WEIGHT BACK-UP

(Weight memory at sudden power failure)

2) Main Functions

■Save date, time and calculated data at sudden power failure

■Various specification of weight conversion speed

(Digital filter function)

■Various printer connection (RS-232C Serial printer)

■Tare weight setting with keys

■Storage of measured times

■Read / Write Set-point values(7) through the PC

- each to set-point code(0~49)

■Read / Write Set Mode values(23) through the PC

■External 6 relays for input / 8 relays for output

■Users can set the max. weight and a division freely

■Control various external equipment by inner external input/output

■Print date and time by built-in clock

■Self hardware test.

3. Technical Specification

■Analog Part & A/D Conversion

Load Cell Excitation Voltage 8 x 350Ωload cells

Zero Adjustment Range 0.05mV 20mV∼

Input Sensitivity 0.6μV/D

System Linearity Within 0.01％of FS.

A/D Internal Resolution 1 / 1,000,000

A/D External Resolution 5,000 dd, 10,000 dd (Max)

A/D Conversion Speed Maximum 200 times/sec

■Digital Part

Span Calibration Full Digital Calibration : SPAC™

(Single pass automatic span calibration)

Input Noise Under ±0.3μVpp

Input Impedance Over 10M Ω

Display VFD (7 digit)

Size of letter 13mm (Height)

Minimum division x1, x2, x5, x10, x20, x50

Display below zero “ - ”

"ZERO" ▼Current weight of “0” kg

"STABLE" ▼Weight is stable

"GROSS" ▼Gross weight is displayed

"NET" ▼Net weight is displayed

"TARE" ▼Tare function is activated

"HOLD" ▼Hold function is activated

" * " ▼" * " key is pressed (print key)

Automatic print is set.

■General Specification

AC 100 ~ 240V (50/60 Hz) Input

DC +3.3V Digital Logic

DC +24V External I/O

DC +5V Analog, Load Cell

Power

AC 3.6V VFD

Product Size 192(W) x 189(D) x 96 (H)

Temperature Range -30 ~℃+60℃

Product Weight Approx. 2.4 kg

4. Measure of Appearance

5. Front Panel

1) VFD Display

■Display Lamp(▼)

ZERO lamp Current weight is 0 kg

ST lamp Weight is stable

GROSS lamp Current weight is gross weight

NET lamp Current weight is net weight

TARE lamp Tare weight is saved

HOLD lamp Lamp is on when HOLD function is activated

Lamp is on only when “*” key is pressed. And F23 is

set to “1” in the set mode

* lamp Automatic print should be set to “1” in set mode

(F41 = 1 or 2, F42 = 1)

2) Keyboard

You can use these keys as numeric keys

Change the set value

key increases set value and key decreases set

value

Change the position of cursor

key moves one digit to right, key moves one digit

to left

Use 1 Enter tare weight

Use 2 Enter set-point value

Use 3 Enter the set value in TEST, CAL, SET mode

■[ ZERO ]Key

Used to remove small variations in the indicator’s zero

■[ TARE ] Key

Used to weigh an item by using the container

Current weight is memorized as tare weight

If you press TARE key in unload condition, tare setting is released

■[ KEY TARE ] Key

When you already know the tare weight, press KEYTARE Key

and enter tare weight by pressing arrow keys and save it by pressing ENTER key

■[ G/N KEY ] Key

Toggles the display between gross and net weight

G. weight lamp on - gross weight / N. weight lamp on - net weight

If tare weight is saved, tare plus item's weight is gross weight and only item's weight is net weight

You can prohibit using of keyboard by pressing G/N key for 5 sec.

To use keyboard again, press G/N key for 5 sec

Tabla de contenidos

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario