CARVIN V3M Guía de instalación y uso

- 1 -

How to bias:

V3M, V3MC

Rev A

9/23/2011

www.carvinservice.com

- 2 -

Only a certified technician should bias Carvin amps, this can be

very dangerous, you can get hurt, please be very careful when

working with any tube amp!

If you are changing the tubes make sure they are a matched set.

-The bias for the V3M, V3MC should be 80mA (measured across the Standby

switch) in the 50W Power Mode setting.

These are the tools you will need:

1. A Phillips head screw driver.

2. A small (plastic if available) flat head screwdriver.

3. A multi-meter, with milli amp (mA) reading.

4. Banana to clip meter leads.

5. An Amp Stand or several wood blocks.

STEP 1

(A) For the V3M, first remove the top grill with the 4 large side screws.

-or-

(B) For the V3MC, first remove the amp from the speaker cabinet:

1. Unplug speaker from rear amp jack.

2. Remove rear wood panel (4 screws on back of cabinet)

3. Remove 4 screws on top of amp.

4. Slide amp out of speaker cabinet, to the rear.

-Replace tubes now if they are to be changed. *Be very careful with the tubes they can break.

STEP 2

Set the amp with tubes down, on an amp stand.

NOTE: If you don't have an amp stand, steadily

support the chassis on solid blocks of wood so that the

power tubes are not touching anything - they get very

hot.

* Be very careful with the tubes they can break.*

STEP 3

Remove the bottom lid by removing the 10 screws

where indicated.

For the V3MC, there are 6 screws to remove the metal plate.

- 3 -

STEP 4

Plug in a speaker to output 1 or 2, they are

both the same, both jacks are in parallel.

IMPORTANT: Do NOT turn on the

amplifier without a speaker plugged in!

STEP 5

Next to the Speaker Output you will find

the OHM setting.

Set the OHM switch to match your

speaker.

Improper OHM settings will not bias

properly, and could result in damage to

the amp!

STEP 6

Set the Power Mode switch in the back to

50W.

NOTE: This step is very important, if

you don’t set this to 50W setting you will

not get the correct bias setting when you

adjust it later in the procedure.

- 4 -

STEP 7

A) Set the Master volume and all channel

Volumes to “0”.

B) Unplug your guitar cord from the input of

the amp.

NOTE: If you have signal going through

the amp, it will not be the true reading

when you set the bias.

STEP 8

Plug in AC Cord.

*Make sure the rear AC switch is set for

the voltage in your area.*

NOTE: Sometimes when the AC Cord is

new it does not want to go in all the way.

Push firmly to force it in, if that is the

case.

STEP 9

Turn the Power Switch ON.

Wait at least 15 seconds, then turn the

Standby Switch to RUN (ON).

Allow 2 minutes for the amp to warm up.

During this time you can set up your Meter

to measure the current (mA) DC.

15secs. > RUN

CAUTION: The tubes get very hot! Don’t touch them, you will burn your skin

if you do.

IMPORTANT: During biasing and normal amp operation if there is a burning smell

or loud crackling noise that comes from the speaker, you should turn off the amp as

the amp may have a bad tube. The tubes should never glow RED on the gray plate

material, the largest metal part inside the tube. This indicates a major problem and

extremely unsafe condition. If this happens turn off the amp immediately!

- 5 -

STEP 10

A) Connect the leads to the meter. B) Set your meter to the milliamp (mA) position.

Make sure the fuse inside is good. Set meter to DC Current, not AC current.

On the meter above, the (mA) and (COM) jacks are used, you have the option to

use the (A) jack, but because the setting will be set to 80mA it’s best to use (mA).

NOTE: If the Fuse inside your meter is open, the meter will not work. It will

always read 0mA.

STEP 11

*WARNING: The Standby switch is connected to HIGH VOLTAGE !

DO NOT touch any metal of the meter lead clips while the meter is connected !

1. 2.

Carefully, connect the two meter lead clips, one to each connector of the Standby

switch. * Once one lead is connected, BOTH leads will have HIGH VOLTAGE.

Make sure the metal of the leads do not touch anything else.

It is usually easier to clip the leads to the wires on the Standby switch than

connecting to the main circuit board.

IMPORTANT: Make sure the Standby switch is set to RUN (ON) before

connecting the leads, or you will get a big spark, and may blow the fuse in the

Meter.

- 6 -

STEP 12

With the meter connected to the Standby switch, turn the switch to Standby (OFF).

The meter should now display a reading near 80mA.

If you have new tubes, this reading will likely be higher or lower.

NOTE: If your meter reads higher that 150mA or goes into overload “OL” , you

should turn off the amp immediately as the amp may have a bad tube.

STEP 13

Use a small, flat head screwdriver.

* A plastic screwdriver is preferred. Use caution if

using a metal screwdriver, to not touch other parts.

-If the meter reads over 80mA, lower the bias

by turning the bias potentiometer clockwise.

-If the reading is under 80mA bring it up by

turning the potentiometer counter-clockwise.

IMPORTANT: Set your meter to DC Current, your meter should read mA DC.

It is OK and normal for the bias reading to fluctuate a little bit and may not be

exactly 80mA, but as close as possible.

Good Bias

Congratulations! Your amp is now properly biased.

*PLEASE READ NEXT PAGE FOR SAFE METER REMOVAL and Power off.

- 7 -

STEP 14

Power down Steps:

1. Turn the STANDBY switch to RUN. (to protect the Meter)

2. Turn the Power switch OFF.

3. Disconnect the meter clips. (Turn the Standby switch OFF for next time)

4. Unplug the AC cord and wait for the tubes to cool down.

5. Attach the bottom cover with screws.

6. Attach the (V3M) top cover, or (V3MC) speaker cabinet.

IMPORTANT: During biasing and normal amp operation if there is a burning smell

or loud crackling noise that comes from the speaker, you should turn off the amp as

the amp may have a bad tube. The same is true if your meter reads higher that

150mA or goes into overload. The tubes should never glow RED on the gray plate

material, the largest metal part inside the tube. This indicates a major problem and

extremely unsafe condition. If this happens turn off the amp immediately!

CAUTION: The tubes get very hot! Don’t touch them, you will burn your skin

if you do. If the amp is ON the tubes will get hot, even if you are not playing

the amp, wait 30 minutes before handling the unit to ensure the amp cooled

down.

NOTE: This is not the only way to set the bias on this amp, this is the Carvin

Approved method which is used on the Production line in the San Diego, California

Factory.

NOTE: If you don’t see any reading on your meter, check the meter. You may have

the leads connected to the wrong jacks on your meter, or the fuse on the meter is

open.

Comments or questions? You can email us at Carvinservice@carvin.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Amplificador de CARVIN

CARVIN

CARVIN KB100 Manual de usuario

CARVIN

CARVIN F150 Manual de usuario

CARVIN

CARVIN HD1000 Manual de usuario

CARVIN

CARVIN DCM1540L Manual de usuario

CARVIN

CARVIN DCM600 Manual de usuario

CARVIN

CARVIN R600 Red Line Series Manual de usuario

CARVIN

CARVIN KB1000 Manual de usuario

CARVIN

CARVIN BX700 Manual de usuario

CARVIN

CARVIN VL100 Manual de usuario

CARVIN

CARVIN XDrive DCM2000Lx Manual de usuario

CARVIN

CARVIN DCM1540L Manual de usuario

CARVIN

CARVIN X1 Manual de usuario

CARVIN

CARVIN Legacy drive vld1 Manual de usuario

CARVIN

CARVIN VL300 Manual de usuario

CARVIN

CARVIN DCM1001 Manual de usuario

CARVIN

CARVIN HD3000 Manual de usuario

CARVIN

CARVIN F600 Manual de usuario

CARVIN

CARVIN BX500 Manual de usuario

CARVIN

CARVIN LT Series Manual de usuario

CARVIN

CARVIN DCM1000 Manual de usuario

CARVIN

CARVIN BRX1018 Manual de usuario

CARVIN

CARVIN HT760M Manual de usuario

CARVIN

CARVIN SX50 Manual de usuario

CARVIN

CARVIN FET 1000 Manual de usuario

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario