Carrier 33CSPGMR-01 Manual de usuario
This unique accessory will allow you to copy stored
information from a thermostat. Then the information
may be loaded into other thermostats, without the
need to manually enter each item.
With the EZ Programmer your options are:
• Copy all data from a thermostat (time, day of
week, time period programming, and advanced
setup information).
• Load just the time and day of week to
a thermostat.
• Load just the time period programming
to a thermostat.
• Load all data to a thermostat (time, day of week,
time period programming, and advanced setup
information).
Page 2
The EZ Programmer has a unique location in its
memory to store data from each thermostat
model that it iscompatible with.
The EZ Programmer will automatically recognize
the thermostat model that it is connected to
and upload the correct data for that model.
The EZ Programmer over writes only the existing
data for the model being downloaded. All
other models' data is untouched.
Examples of how this programmer can be used
include:
•Extract programming data from a thermostat
in the shop and upload it to thermostat(s) in
the field.
• An easy way to make the same program
changes on multiple thermostats at the same
location.
• An easy way to change the time on multiple
units.
Page 3
The accessory connector of the
programmer =s inserted into the
accessory jack.
Accessory release button
Accessory jack located on
thermostat bottom
Accessory connector
The LED will glow green
when connected to a
compatible thermostat
To release the programmer from
the thermostat: press and hold
the accessory release button
on the front panel of the thermostat,
while pressing the release button,
remove the programmer.
Page 4
After the accessory connector
of the programmer is inserted
into the accessory jack of a
compatible thermostat:
OThe LED will flash red a
number of times based
on the model of the
thermostat it recognizes.
Reconnect, if the red/green
LED does not flash at all.
Red/Green LED 1 flash = 33CS400-01
2 flashes = 33CS420-01
3 flashes = 33CS450-01
The LED will turn green when
the programmer is ready to
continue.
_1 The LED will turn red during
operation and back to green
when finished.
CAUTION Do not remove the Ez Programmer from the
_ hermostat while the LED is red. If the LED is
red longer than 3 seconds, remove it from the
thermostat as this is an abnormal condition.
In this case let the programmer sit 5 seconds,
then reconnect and retry the previous operation.
Page 5
ALL
This button, when pressed, will
copy (download) all the stored
data from the connected thermostat
to the programmer. The LED will turn red,
then will turn green when complete.
TIME
PERIOD
©
CLOCK
ONLY
ALL
This button, when pressed, will
copy (upload) the time period
programming from the programmer
to the connected thermostat.
The LED will turn red, then turn
green when complete.
This button, when pressed, will
copy (upload) the time & day of
week from the programmer to the
connected thermostat.
The LED will turn red, then will
turn green when complete.
See note on page 9.
This button, when pressed, will
copy (upload) all the stored data
from the programmer to the
connected thermostat.
The LED will turn red, then turn green
when complete.
Page 6
To u_01oad All data programming:
ALL
T
This button, when pressed, will
copy (upload) all the stored data
from the programmer to the
connected thermostat.
The LED of the programmer will turn
red, then turn green when copying is
complete.
To download All data:
This button, when pressed, will
o opy (download) all the stored data
from the connected thermostat to
the programmer.
ALL The LED of the programmer will
tturn red, then turn green when
copying is complete.
Page 7
To u_01oad Time Period programming:
This button, when pressed will
copy (upload) all the time period
data from the programmer to the
connected thermostat.
The LED of the programmer will
turn red, then turn green when
copying is complete.
TIME
PERIOD
Page 8
To u_oload Time & Day of Week:
This button, when pressed, will
copy (upload) the time & day
of the week from the programmer
to the connected thermostat.
The LED of the programmer will
turn red, then turn green when
copying is complete.
Note: If connected to a thermostat
that does not have a clock, the
programmer will not try to transfer
the clock information. In this case
the LED will not flash red.
Page 9
To completely erase all of
the contents of the
programmer and restore
it to its factory default
values, insert a paperclip
into this hole and depress
the small reset switch.
Screw holding the
battery cover.
replace the battery:
Remove the screw holding
the battery cover.
Slide off the battery cover
& replace it with a CR-2032,
or equivalent battery.
The internal clock will
need to be reset after
replacing the battery.
To do this, connect the
programmer to a
compatible thermostat
with a clock and day of
the week display.
Confirm the current day
and time, then press _"
Page t0
Este manual sirve para los siguientes modelos
1
Otros manuales de Mando a distancia de Carrier
Carrier
Carrier RG10L1/BGEF Manual de usuario
Carrier
Carrier BMY33HH20WM Manual de usuario
Carrier
Carrier RG56V Series Manual de usuario
Carrier
Carrier Infinity SYSTXCCRWF01 Manual de usuario
Carrier
Carrier RG67V/BGEF Manual de usuario
Carrier
Carrier RG66B3/BGEF Manual de usuario
Carrier
Carrier NTC-IR2 Manual de usuario
Carrier
Carrier OSK102 Manual de usuario
Carrier
Carrier RG10A2/BGEF Manual de usuario
Carrier
Carrier WTC-IR Manual de usuario
Carrier
Carrier SYSTEM PILOT 33PILOT-01 Manual de usuario
Carrier
Carrier NTC Manual de usuario
Carrier
Carrier HDB Manual de usuario
Carrier
Carrier rg05 Manual de usuario
Carrier
Carrier 33CSIRRCVR-01 Manual de usuario
Carrier
Carrier split room air conditioner remote control Manual de usuario
Carrier
Carrier SYSTXCCITW01-A Infinity Manual de usuario
Carrier
Carrier rg05 Manual de usuario
Carrier
Carrier RG67V/BGEF Manual de usuario
Carrier
Carrier TruVu UC683T Manual de instalación
