Carmelli NG1022M Manual de usuario
TRIPLE THREAT 3-IN-1 FLIP TABLE
ASSEMBLY INSTRUCTIONS
NG1022M
Please Do Not Hesitate to
Contact Our Consumer Hotline
at 800-759-0977
with Any Questions That May
Arise During Assembly or
Use of This Product!
THANK YOU!
Thank you for purchasing this product.
We work around the clock and around the globe to ensure that our products
maintain the highest possible quality. However, in the rare case of issues
during assembly or use of this product, please contact our Consumer Hotline
at 800-759-0977 for immediate assistance before contacting your retailer.
Please read the warranty information at the back of these assembly
instructions for further details.
IMPORTANT! PLEASE READ THESE ASSEMBLY INSTRUCTIONS
IN ENTIRETY BEFORE ASSEMBLING YOUR PRODUCT.
2
44
Qty.
1
Preassembled Fan
NGP58131
5
ASSEMBLY TIPS
1. Find a clean, level surface to begin the assembly of your game table. We recommend
that two adults work together to assemble this game. You may want to carefully cut or tear
the four corners of the box so that the bottom of the box can be used as your work surface.
2. Remove all of the contents from box and verify that you have all of the parts shown on
Note: Some parts may be pre-installed
or pre-assembled.
understand the text before beginning each assembly step.
4. When installing parts that have more than one screw or bolt, hand tighten all
5. Electric screwdrivers may be helpful during assembly; however, please set a low torque
and use extreme caution because screws may be stripped or overtightened, resulting in
damaged parts, if the electric screwdriver’s torque is set too high.
WARNINGS!
READ AND FOLLOW ALL ASSEMBLY, OPERATION AND SAFETY INSTRUCTIONS CAREFULLY.
CHOKE HAZARD - THIS TABLE CONTAINS SMALL BALLS AND PARTS
NOT SUITABLE FOR CHILDREN UNDER 3 YEARS OF AGE.
THANK YOU!
6
ASSEMBLY INSTRUCTIONS
6
STEP 1 - ASSEMBLE THE LEGS
1. Select one of the leg pieces (#9 or #10) and lay it flat on the floor. Do not bend the hinge
in the leg backwards. Damage to the outer surface will occur.
2. Position three of the “L” shaped steel brackets (#39) on one side of the leg. Use three
screws (#43) to attach the brackets to the leg. Close (fold) the leg and use three screws
(#43) to secure the brackets. Tighten the screws.
3. Place a leg base (#11) at the bottom and insert three screws (#25) into the holes. The
pressed in nut must be facing out away from the leg.
4. Tighten the screws.
5. Screw a leg leveler (#13) half way into the leg base.
6. Repeat for the remaining three legs.
The nut side must
be facing upwards
43
39
9
THANK YOU!
7
ASSEMBLY INSTRUCTIONS (CONT.)
7
STEP 2 - ATTACH THE TABLE LOCKS AND CATCH BOX
1. Insert the table locks (#14) into the end panel (#3). Use four screws (#27) to secure each
one.
2. Hold the catch box (#4) in position. Insert four screws (#25) from the back side of the end
panel.
3. Tighten the screws.
4. Repeat for second end panel
STEP 3 - ASSEMBLE BALL RETURN BOARD
1. Attach the ball return boards (#5) to the bottom of the end panels (#3). Use four screws
(#25) per ball return board.
2. Tighten the screws.
Open (unlocked Closed (locked)
THANK YOU!ASSEMBLY INSTRUCTIONS (CONT.)
8
STEP 4 - ASSEMBLE LEGS TO END PANELS
1. Insert four barrel nuts (#22) into the left and right holes of an end panel (#3). Attach a left
leg (#9) and a right leg (#10) to an end panel (#3) using two bolts (#16) per leg.
2. Attach a leg panel (#8) to the legs and secure it using four screws (#24) per leg panel.
3. Repeat steps 1 and 2 to assemble the other apron and legs.
STEP 5 - ATTACH LEG BRACES
1. Insert four barrel nuts (#23) into the holes of the leg braces (#7) as shown. Attach the leg
braces (#7) between the assembled legs using four washers (#21) and four bolts (#17)
per leg brace.
10
Note：MAKE SURE THAT ALL CONNECTIONS
ARE PROPERLY ASSEMBLED
9
9
10
THANK YOU!ASSEMBLY INSTRUCTIONS (CONT.)
9
STEP 6 - ASSEMBLE CABINET (TABLE TOP) TO LEGS
All bolts and screws from previous steps must be tight. Two adults are recommended for this
step.
1. Engage all four table locks.
2. Locate the two large bolts (#18). Place a washer (#19) onto each bolt.
3. Place a second washer (#20) onto the bolts.
4. Finger start a bolt into each end of the cabinet (#1).
5. Place the cabinet into position. The bolts will drop into the slots at each end. The smaller
washer must be outside the end panel and the plastic washer must be between the end
panel and the cabinet.
NOTE: The electrical cord must be loose.
6. Open the table locks. Tighten the bolts until they are snug and the cabinet can rotate
smoothly.
THANK YOU!ASSEMBLY INSTRUCTIONS (CONT.)
10
STEP 7 - ASSEMBLE TOP SIDE PANELS AND SLIDE SCORERS
1. Attach the two top end panels (#6) to the top of the end panels (#3) using eight screws
(#25) for each top end panel.
2. Attach the slide scorers (#15) to the top end panels (#6) using two screws (#26).
3
Otros manuales para NG1022M
1
Tabla de contenidos
Otros manuales de Juego de Carmelli
Carmelli
Carmelli NG2315P Manual de usuario
Carmelli
Carmelli PHANTOM NG1038H Manual de usuario
Carmelli
Carmelli AUSTIN 9' SHUFFLEBOARD TABLE Manual de usuario
Carmelli
Carmelli EXCALIBUR NG5030 Manual de usuario
Carmelli
Carmelli BRISTOL NG4023 Manual de usuario
Carmelli
Carmelli FAIRMONT NG2574 Manual de usuario
Carmelli
Carmelli NG4009H Manual de usuario
Carmelli
Carmelli BG1135F Manual de usuario
Carmelli
Carmelli NG2019SK Manual de usuario
Carmelli
Carmelli NG1216 Manual de usuario
Manuales populares de Juego de otras marcas
Koala Technologies
Koala Technologies KoalaWare Spider Eater Manual de usuario
Tomy
Tomy The Magic Oven Manual de usuario
Sega
Sega GAME SHOW Manual de usuario
Tiger Electronics
Tiger Electronics Last Out 7-584-0 Manual de usuario
Fisher-Price
Fisher-Price RollOverRover Manual de usuario
Mattel
Mattel World Championship Football Manual de usuario