Carbine 32cs Manual de usuario
1
OWNER ’S MANUAL
®
SECURITY SYSTEM with KEYLESS ENTRY
2
Congratulations
Congratulations on the purchase of this CARBINE security system.
Reading this owners guide prior to using the system will familiarize
you with it’s many features. If issues arise or you have questions,
contact your installing dealer first. Additionally, you can contact us
online at www.carbine.com or call 310-735-2000.
3
Replacement Remote Controls
To purchase replacement remote controls, please
see your authorized dealer/installer or visit us at
www.carbine.com
Remote part numbers are found on the back of the remote control.
4
Contents
Congratulations ............................................................................. 2
Replacement Remote Controls....................................................... 3
4-Button Remote Configuration...................................................... 5
Using the System
Arming/ Disarming ........................................................................ 6
Disarm without a Transmitter......................................................... 6
Panic Alarm ................................................................................... 7
Channel #3 and #4 Operation ........................................................ 7
Valet Mode .................................................................................... 8
Trigger the System......................................................................... 9
Tamper Warnings........................................................................... 9
Replacement Remote Pairing....................................................... 10
Battery Replacement ................................................................... 11
5
Remote Controls
4 Button Remote Configuration
Button Function Action
Arm/ Lock Press and Release
Turn Off Panic Alarm Press and Release
Disarm/ Unlock Press and Release
Turn Off Panic Alarm Press and Release
Activate Trunk Release
(CH#3)
Press and Hold for
2 Seconds
Initiate Silent Arm or
Disarm
Press and Release
Before Pressing Lock
or Unlock
Panic Alarm On/Off Press and Hold for
2 Seconds
+AUX Channel 4 Output Press Both and Hold
for 3 Seconds
--Valet Mode On/Off Press each button in
sequence
6
Lock/ Arm
- Press and release the button to arm the security system
and lock the doors. The parking lights will flash one time.
(door lock control must be installed)
Unlock/ Disarm
- Press and release the button to disarm the security
system and unlock the doors. The parking lights will flash
two times. (door lock control must be installed)
Silent Arm/ Disarm
Quickly press and release the button before pressing the
or button to initiate silent mode. The system will lock or unlock
without arming or disarming chirps.
Note: If the system had previously been triggered, the tamper
warning chirps will always sound upon disarm.
Disarm without the Remote Control
Your CARBINE system has an override mode that allows you to
disarm your system in the event that you have lost or damaged
your remote controller.
- While the alarm is sounding, turn the ignition key to On,
then press and release the valet switch button. This will
disarm the system.
Note: If your system was installed and programmed to “Automati-
cally Arm”, the system should be placed into “Valet Mode”
to prevent it from become re-armed until you can correct
the issue with your remote control.
7
Panic Alarm
1. Press and hold the button for 3 seconds to activate panic
alarm. Once activated, the panic alarm will sound the horn or
siren and flash the parking lights for 30 seconds.
2. Press and release the or button to stop the
panic mode.
Note: You can also press and hold the button for
3 seconds to stop the panic alarm.
Trunk Release (CH#3)
Press and hold the button for 3 seconds to
release the trunk/ hatch lid
- The vehicle must have electronic trunk control
- The trunk release control option must be installed
AUX Output Activation (CH#4)
Depending on your installation, your installer may have connected
the channel #4 output to your vehicle. To activate the AUX/CH#4
output, press and hold the + buttons together for 2 seconds.
This action will energize the White/Blue wire for as long as you hold
the buttons down. The operation of AUX Channel #4 is programmable.
8
Valet Mode (By Valet Button)
Valet mode is a convenience when you take your car in for service
or allow someone who may not be familiar with your security
system drive your vehicle.
- All doors must be closed
- Turn the ignition key On then Off.
- Press and release the valet button (1) time.
The status LED will be on.
- Repeat the procedure to turn off the valet mode.
The status LED will be off.
Valet Mode (By Remote)
Valet mode is a convenience when you take your car in for
service or allow someone who may not be familiar with your
security system drive your vehicle. To activate Valet Mode using
your remote control. Repeat the following procedure.
1. Open the driver’s door.
2. Press - - on your remote control.
3. The LED status indicator will be on solid.
4. Repeat 1 and 2 above to exit Valet Mode.
The status LED indicator will be off.
9
Trigger the System
If at any time the system becomes triggered, the horn/siren will
sound for 30 seconds and then re-arm. If a protected entrance is
left open, the alarm will sound for three, 30 second cycles and then
the protected entrance is bypassed while the remaining detection
zones are active.
Tamper Warning at Disarm
If the alarm had been triggered while you were away from the
vehicle, upon disarming, a 4-chirp tamper disarm warning will
occur. In addition to the 4-chirp warning, the status LED will
flash a distinctive number of times to indicate which alarm
zone set off the alarm.
Tamper LED Flashes Trigger Source
1 Doors
2Hood/ Trunk
4 Shock Sensor
5Ignition Voltage
6 Tilt Sensor
10
Pairing a Replacement Remote Control
Your CARBINE system remote controls are already paired to the
control module. If you are replacing or adding remotes to your
system, they must be programmed (paired) to the control module
before they will operate the system. In order to perform remote
control pairing, you must know where your “Valet Button is located
as you will use the button and the LED indicator to perform the
pairing function.
Remote Pairing Procedure
1. Open the driver’s door.
2. Insert the ignition key into the key cylinder.
Turn ON the ignition key
3. Press and release the valet button then press and hold the valet
button for 1.5 seconds. The LED flashes and the horn chirps
(if connected). Release the valet button. The system will stay in
Pairing mode for 60 seconds.
5. Press and hold the button on the new remote control.
6. Press and release the button 5 times. The LED on the
remote will begin a steady flash. Release all buttons.
The LED will flash for 15 seconds.
7. Press and release the button on the new transmitter. The
horn/siren chirps and the LED flash pauses to indicate that the
new remote is programmed.
8. Turn the ignition key to the Off position. A long chirp from the
horn confirms that the pairing mode is off.
Note: Your CARBINE security system will accept codes from
up to (4) transmitters.
Otros manuales para 32cs
1
Tabla de contenidos
Otros manuales de Alarma de coche de Carbine
Carbine
Carbine PLUS-6900 Manual de usuario
Carbine
Carbine PLUS-5500 Manual de usuario
Carbine
Carbine PLUS-4700 Manual de usuario
Carbine
Carbine PLUS-5600 Manual de usuario
Carbine
Carbine PLUS-4950 Manual de usuario
Carbine
Carbine PLUS-5600 Manual de usuario
Carbine
Carbine 34cs Manual de usuario
Carbine
Carbine PLUS-4900 Manual de usuario
Carbine
Carbine PLUS-4800 Manual del propietario
Carbine
Carbine PLUS-4000 Manual de usuario
Manuales populares de Alarma de coche de otras marcas
Federal Signal Corporation
Federal Signal Corporation Pathfinder Siren Series Manual
Falcon
Falcon Predator XL3 Guía del usuario
Audiovox
Audiovox Auto Security XR91 Instrucciones de funcionamiento
Clifford
Clifford Sabre II Manual de usuario
CrimeStopper
CrimeStopper CS-8717 Guía de inicio rápido
Ultra Start
Ultra Start 450 SERIES Manual de usuario
