Canon ImageCLASS MF5730 Manual

Set-Up Instructions

Thank you for purchasing Canon imageCLASS MF5730.

To get your machine ready for use, please follow the instructions in this document before referring to any other documentation.

Unpack the machine and its components.

Check that you have the following:

●Machine

●Cartridge

NOTE

●The cartridge included with the machine is Cartridge X25 that yields approximately 2,500 pages of printouts (Letter at 4%

dot coverage).

Before setting up the machine:

1Place the machine on a flat, stable surface.

2Remove all shipping tape from the exterior of the machine.

Referring to the following figure, remove the tape and spacers on both sides of the

cassette housed in the machine.

●Cassette extension

●Extension cover

●Power cord

●USB cable

●Set-Up Instructions

●Basic Guide

●Warranty

●

Limited Warranty Note for Cartridge X25

●Registration Card

●MF5700 Series User Software CD-ROM

E227ME (MF5730) US2 SI.qxd 2/1/05 11:57 AM Page 1

Assemble the cassette and load paper.

Install the cartridge.

4Pull open the front cover.

1Remove the cartridge from the bag. Keep the

bag in a safe place for future use.

2Gently rock the cartridge several times to

evenly distribute the toner inside.

3Hold the cartridge on a flat stable surface with

one hand, and break the tab ➊and pull out

the seal ➋completely with the other hand.

5Hold the cartridge so that the instructions (A)

and the arrow (B) are facing up, and insert it in

the machine horizontally as far as it will go.

6Close the front cover of the machine.

Hold the document feeder (

) with one hand,

and open the document feeder tray (

) with

the other.

Pull out the paper cassette completely.

NOTE

●Pull the cassette straight/forward. Pulling it at an angle

may damage the paper sensing lever inside the

machine.

E227ME (MF5730) US2 SI.qxd 2/1/05 11:57 AM Page 2

3Attach the extension to the cassette.The slots

➊are keyed and must be inserted at a 90°

angle. Once inserted, fold the extension as

shown ➋.

4Pinch and slide the rear paper end guide to

match the size of paper.

NOTE

●Confirm that the paper guide is fitted in the paper size

slit correctly.

5Load the paper into the cassette. Make sure

the paper stack sits below the hooks (A)

6Pinch and slide the side paper end guides to

match the size of paper.

To load Legal-size paper:

Pull the blue tab ➊and extend the cassette ➋as far as it will go. Keep the rear paper end guide to LTR

size mark. If you are not using Legal-size paper, skip to the next step without extending the cassette.

E227ME (MF5730) US2 SI.qxd 2/1/05 11:57 AM Page 3

7Even out the edges of the paper stack.

Make sure the height of the stack does not

exceed the limit marks (A) and that

the side edges of the stack are below the

hooks (B).

9Insert the tabs on the extension cover into the

slots ➊on the back of the machine,

and carefully lower the cover ➋until it sits on

the cassette extension beneath it.

8Insert the paper cassette back into the

machine as far as it will go.

NOTE

●If you do not completely insert the cassette into the

machine, paper jams may occur.

IMPORTANT

●Do not push in the cassette at an angle. Doing so

may damage the paper sensing lever inside the

machine.

IMPORTANT

●Do not load paper from the back of the machine.

Doing so may damage the paper feeding assembly

inside the machine.

E227ME (MF5730) US2 SI.qxd 2/1/05 11:57 AM Page 4

2Once it is warmed up, the standby display

appears in the LCD.

Connect the power cord.

1Plug the power cord into the rear socket ➊.Then connect the other end to the wall outlet ➋.

IMPORTANT

●For important safety instructions on installation and handling of the machine, see “Important Safety

Instructions” in the Basic Guide.

NOTE

●Make sure the correct paper size is specified in the machine. For details, see Chapter 2,“Paper Handling,”in the Basic

Guide.

E227ME (MF5730) US2 SI.qxd 2/1/05 11:57 AM Page 5

Install the software.

IMPORTANT

●Do not connect the USB cable before installing the software. If you connect the USB cable before installing the

software and the Found New Hardware Wizard screen appears, click [Cancel] and disconnect the USB cable.

●Network Connection is not available for this model. If you selected [Network Connection] by mistake, go back to

the previous screen by clicking [Back], and select [USB Connection].

NOTE

●The instructions below are for Windows XP/Server 2003. For Windows 98/Me/2000, see the Software Guide (included in

the User Software CD).

●For Windows 2000/XP/Server 2003, log on as Administrator to install the software.

1Turn on your computer.

2Quit any open applications, including aniti-virus

software.

3Insert the User Software CD into the CD-ROM drive.

4When the MF Setup screen appears, click

[USB Connection].

NOTE

●If the MF Setup screen is not displayed, on the Windows desktop, click [start] ➝

[My Computer]. Open the CD-ROM icon, then double-click

[Setup (Setup.exe)].

5Click [Install Drivers].

NOTE

●If you would like to install the Presto! PageManager file management software

and/or OmniPage SE OCR software, click [Install Applications] and follow the

instructions on the screen.

●You can also click [Read Manuals] on this screen to read PDF manuals.

6Click [Install MF Drivers].

7When the MF Drivers-Setup Wizard screen

appears, click [Yes] and follow the instructions

on the screen.

E227ME (MF5730) US2 SI.qxd 2/1/05 11:57 AM Page 6

8When the installation is complete, click [Exit] to

close the MF Drivers-Setup Wizard screen.

9On the MF Setup screen, click [Install MF Toolbox].

10 When the MF Toolbox-Setup Wizard screen

appears, click [Next] and follow the instructions

on the screen.

NOTE

●Before installing MF Toolbox, make sure that all other

applications are closed and that any anti-virus software on

your computer is disabled.

11 When the installation is complete, click [Exit]

to close the MF Toolbox-Setup Wizard

screen.

E227ME (MF5730) US2 SI.qxd 2/1/05 11:57 AM Page 7

Part no. FA7-6515 (010)

Canon and imageCLASS are trademarks of Canon Inc.

All other products and brand names are registered

trademarks or trademarks of their respective owners.

Specifications subject to change without notice.

PRINTED IN CHINA

Congratulations! You have now completed the machine setup.

Where to go from here...

Once you have completed all steps in this document, see the Basic Guide for basic

operations of all functions of your machine.

For information on the driver software, see the Software Guide (included in the User

Software CD).

NOTE

●Remember to register your machine to ensure product support. The serial number is located on the back of the

machine.

Connect the machine to your computer.

1Make sure the machine’s power is turned on.

Connect the cable to the USB port on the

back of the machine.Then connect the other

end of the cable to the USB port on your

computer.

2After the installation is complete, click [Exit]

to close the MF Setup screen. Remove the

User Software CD from the CD-ROM drive

and store it in a safe place.

NOTE

●If you would like to install the optional Presto! PageManager file management software and/or OmniPage OCR software,

click [Install Applications] and follow the instructions on the screen.

●You can also click [Read Manuals] to read PDF manuals in the User Software CD. To view the manuals in PDF format,

Adobe Reader/Acrobat Reader/Acrobat is required. If Adobe Reader/Acrobat Reader/Acrobat is not installed on your

system, please download it from the Adobe Systems Incorporated website (http://www.adobe.com).

For installation help and operational instructions, call us at:

1-800-828-4040 1-800 OK CANON

U.S.A. CUSTOMERS CANADA CUSTOMERS

E227ME (MF5730) US2 SI.qxd 2/1/05 11:57 AM Page 8

Otros manuales para ImageCLASS MF5730

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Impresora todo en uno de Canon

Canon

Canon imageRUNNER C3480 Manual de usuario

Canon

Canon ImageRunner C2550 Instrucciones de instalación y mantenimiento

Canon

Canon MF5750 - ImageCLASS B/W Laser Manual de usuario

Canon

Canon PIXMA MX850 Manual de usuario

Canon

Canon Pixma MG7100 Series Guía de configuración

Canon

Canon PIXMA MP228 Manual de usuario

Canon

Canon PIXMA E481 Guía de configuración

Canon

Canon imageCLASS MF4140 Guía del usuario

Canon

Canon iR2020 Series Manual de usuario

Canon

Canon 2911B002 Manual de usuario

Canon

Canon MF4010 Series Guía del usuario

Canon

Canon imageRUNNER ADVANCE C2225 Instrucciones de montaje

Canon

Canon PIXMA MG6450 Manual de usuario

Canon

Canon MX520 series Instrucciones de instalación y mantenimiento

Canon

Canon iR3530 Manual de referencia

Canon

Canon SmartBase 1270D Manual de usuario

Canon

Canon PIXMA MG3022 Guía de configuración

Canon

Canon ImageCLASS D420 Instrucciones de montaje

Canon

Canon PIXMA MG5320 Series Manual de usuario

Canon

Canon i-SENSYS MF6140dn Manual de usuario

Canon

Canon MX530 series Guía de configuración

Canon

Canon LASER CLASS 1060P Manual de usuario

Canon

Canon LaserBase MF5770 Manual de usuario

Canon

Canon MultiPASS F60 Manual de usuario

Manuales populares de Impresora todo en uno de otras marcas

Triumph Adler

Triumph Adler DC 2016 Manual

Epson

Epson WorkForce WF-2510 Guía del usuario

Epson

Epson Stylus Scan 2000 Manual de instalación y operación

Epson

Epson PictureMate Snap PM 240 Manual de instrucciones

Konica Minolta

Konica Minolta bizhub C35 Manual de usuario

Brother

Brother MFC-J430w Manual de usuario

Konica Minolta

Konica Minolta BIZHUB 558 Manual de usuario

Lexmark

Lexmark MX710 Series Manual

Brother

Brother MFC-9760 Manual de usuario

Lexmark

Lexmark XC8155 Manual de usuario

Lexmark

Lexmark X642E Manual de usuario

Sharp

Sharp MX-2310U Guía

Aficio

Aficio 200 Manual de usuario

Ricoh

Ricoh Pro C900 Manual de usuario

Lexmark

Lexmark X925 Manual de usuario

Brother

Brother Business Smart MFC-J4510dw Manual de usuario

Epson

Epson Stylus CX8400 Series Manual de usuario

Oce

Oce VarioLink 5022 Manual de usuario