Cannondale Carbon Road Disc Manual de usuario

Carbon Road Disc

Quick Start Guide

Applies to: Topstone Carbon,

Synapse Carbon, Super X

Welcome to the Cannondale family.

WARNING

SET-UP STEP 2STEP 1 STEP 3 STEP 4 PRE-RIDE CHECK

This is a Quick Start Guide, not an

Owner’s manual.

Bicycling is an active sport with

inherent risk. A wide range of injuries

are possible. Due to the nature of

bicycle riding, the situations you

encounter while riding, you will be

exposed to the risk of serious injury,

paralysis or death. This risk cannot

be eliminated. You can minimize the

risk in many ways. Begin by reading

the complete Cannondale Bicycle

Owner’s manual accompanying

this bike and available online at

www.cannondale.com, particularly

section “IMPORTANT SAFETY

INFORMATION”.

First up, thank you for buying a new Cannondale bike – we’re excited to

have you on board and to get you out riding as soon as possible. Our new

assembly process is easy-to-follow – using methods outlined in this guide

to assemble your new Cannondale at home, plus it’s even easier to do so

with a friend. Our guide will take you through the simple steps from start

to nish – you can also follow along with a how-to video, as you build your

bike, just visit: [email protected]

If you still have any questions, then our Cannondale rider support sta are

ready to help you. Feel free to give us a call at

Also, when your new bike is all assembled and ready to ride, we’d love to

check it out – please don’t forget to tag #ridecannondale in your social

media. Enjoy the ride!

SET-UP STEP 2STEP 1 STEP 3 STEP 4 PRE-RIDE CHECK



Install your

handlebars



Install your

seat post



Install your

front wheel



Install your

pedals





This video applies to one Cannondale Platform:

• Topstone Carbon, Synapse Carbon, Super X

Tools Needed:

• Flat-Head Screwdriver

• Phillips-Head Screwdriver

• Box Cutter

• Scissors

Tools Included:

• Torque Wrench

• Allen Keys

• Pedal Wrench

Gently lift your bike out of the box and set

it on top of the box. Make sure the attached

wheel is facing upwards

SET-UP STEP 2STEP 1 STEP 3 STEP 4 PRE-RIDE CHECK

Inside the box, you’ll nd a smaller box of parts, necessary tools,

documentation and manuals. Once the bike is assembled, but

before you ride, please read the owner’s manual.

First, locate the staples on the top of the box and carefully remove

them with a screwdriver. Use caution: the staples are sharp.

Push the hand aps from the inside to the outside of the box. This

will make removing the bike easier.

Carefully lift the bike out of the box and set it onto the top of the box.

Remove the front wheel from the bike by carefully removing the zip

ties or Velcro. Then, remove all packaging from the wheel and set it

aside.

Remove all additional packaging from the bike, letting the handlebar

gently hang from the frame.





Lift the entire bike up o the box and set the

rear end into the standing box.

The front fork should rest over the edge of the

box.

SET-UP STEP 2STEP 1 STEP 3 STEP 4 PRE-RIDE CHECK



Carefully lift and rotate the bike, lowering it gently back into the box

with the fork overhanging the box side. The stem should be pointing

forward and the disc brake caliper should be on the left (non-

drivetrain) side of the bike.

SET-UP STEP 2STEP 1 STEP 3 STEP 4 PRE-RIDE CHECK

 A

Using anAllenwrench, loosen and removethefourbolts andfaceplate

from the stem. The stem connects the handlebar to the fork. Set the

bolts and faceplate aside together, so you don’t lose anything.

Insert the handlebar into the stem and verify the brake hoses and

shift cables wrap around the frame cleanly, without kinks to any of

the lines.

Loosely reattach the faceplate to the stem. Take care to not tighten

one bolt more than another. Your goal is a consistent gap between

the stem and faceplate.

Center the handlebar in the stem using the markings on the bar, then

roll it back into a comfortable position. Lightly hand-tighten the stem

bolts using the Allen key, ensuring there’s an even gap between the

stem and faceplate. We’ll fully tighten these later.



SET-UP STEP 2STEP 1 STEP 3 STEP 4 PRE-RIDE CHECK



Locate the seatpost wedge in the parts bag. Identify the rounded

face on the wedge assembly and cover it with the provided grease.

Do NOT use carbon paste on this surface.

Use an Allen wrench to help guide the wedge into position in the

frame. Firmly push the seatpost wedge into the frame.

Apply carbon paste to the back of the seatpost wedge assembly and

the inside of the seat tube.

Locate the minimum insertion line on the seatpost.

Insert the seatpost into the frame beyond the minimum insertion line,

then hand tighten the seatpost wedge using the Allen key, enough so

the seatpost can’t be pulled from the frame. It will be fully tightened

later.

Carefully lift the bike from the box and gently place the fork ends on

the ground.





SET-UP STEP 2STEP 1 STEP 3 STEP 4 PRE-RIDE CHECK



Unthread and remove the thru-axle from the fork and place it on a

clean surface.

The speed-release is basicallya thru-axle boltwith a groove machined

into the shaft to ease wheel removal and installation.

Install the speed-release thru-axle into the hub on the non-disc brake

side. Be sure to line up the groove in the speed-release thru-axle with

the outside of the hub.

Remove the pad spacer in the disc brake caliper.





Identify the disc brake rotor side of the front wheel. Orient the wheel

so the rotor is on the left side – the same side as the front brake pads.

Gently lift the front of the bike and roll the front wheel back into the

fork.

Carefully guide the right-side fork dropout onto the groove in the

speed-release thru-axle.

Use a hex wrench to rmly tighten the speed-release thru-axle. When

properly tightened, the wrench should leave a mark on your hand.

At this point you can remove any additional packaging from the bike.



SET-UP STEP 2STEP 1 STEP 3 STEP 4 PRE-RIDE CHECK



Install your chosen pedals by turning the pedal spindle in the

direction of the front wheel. Insert the right pedal (marked with R on

the spindle) into the crank and tighten with your ngers. Repeat with

the left pedal (with an L on it).

Tighten both pedals down very rmly with the appropriate Allen or

15mm pedal wrench.



SET-UP STEP 2STEP 1 STEP 3 STEP 4 PRE-RIDE CHECK

Otros manuales de Bicicleta de Cannondale

Cannondale

Cannondale Claymore Guía de configuración

Cannondale

Cannondale Slice Manual de usuario

Cannondale

Cannondale Adventure Neo Allroad S 2023 Manual de usuario

Cannondale

Cannondale Jekyll Manual de usuario

Cannondale

Cannondale TANDEMS 2009 Manual de usuario

Cannondale

Cannondale Topstone Neo Lefty Manual de usuario

Cannondale

Cannondale E-Series Guía de configuración

Cannondale

Cannondale Bicycles Manual de usuario

Cannondale

Cannondale Synapse HM Guía de configuración

Cannondale

Cannondale LEFTY HYBRID Guía de configuración

Cannondale

Cannondale en 14764 Manual de usuario

Cannondale

Cannondale Quick Neo SL w/ Ebikemotion X35 Drive System... Manual

Cannondale

Cannondale 2012 RZ ONE TWENTY Guía de configuración

Cannondale

Cannondale Kinneto E-Series Manual de usuario

Cannondale

Cannondale Slice Carbon Guía de configuración

Cannondale

Cannondale Trigger 2019 Guía de configuración

Cannondale

Cannondale Alloy Road Rim Manual de usuario

Cannondale

Cannondale Trigger 29ER Manual de usuario

Cannondale

Cannondale Synapse Carbon Guía de configuración

Cannondale

Cannondale F-SI Manual de usuario

Cannondale

Cannondale 2016 SUPERSIX EVO Guía de configuración

Cannondale

Cannondale MOTERRA LT Manual de usuario

Cannondale

Cannondale Full-Suspension EBike Manual de usuario

Cannondale

Cannondale CY22 Mavaro Neo Guía de configuración

Manuales populares de Bicicleta de otras marcas

RAMBO

RAMBO R1000X2M-FF-BFD Manual de usuario

Vermeiren

Vermeiren SAFARI Manual de usuario

Velec

Velec A2/36V Manual de usuario

Coswheel

Coswheel A-ONE Manual de usuario

Betzold

Betzold 97869 Manual de usuario

Cervélo

Cervélo S3 2019 Manual de usuario

Tenways

Tenways AGO X Manual de usuario

Festo

Festo EGSC-BS-KF Manual de lista de piezas

Gio Electric

Gio Electric H1 Volt Manual de usuario

GOGOBEST

GOGOBEST GM30 Manual de usuario

DAHON

DAHON CIAO - 2009 Manual de usuario

Aprimatic

Aprimatic ONDA 500 Guía de inicio rápido

MV Agusta

MV Agusta Lucky Explorer GRAVEL Manual de instrucciones

Greyp

Greyp G6 Series Manual de usuario

Babboe

Babboe Carve-E Manual de usuario

Huka

Huka orthros Manual de usuario

Xtracycle

Xtracycle Stoker 2021 Manual de usuario

APRILIA

APRILIA DORSODURO 750 ABS 2015 Manual de usuario