Canadian Spa CRS 1 Manual de usuario

Bottom mount cover lifter (CRS 1)

BEFORE BEGINNING ASSEMBLY,

CAREFULLY READ THE INSTRUCTIONS:

Place all parts in a cleared area and remove the

packing materials. Assembly requires two people.

For help identifying the small parts used in

assembly, use the Parts List.

Note: During assembly, make sure that all parts are

oriented as shown in the drawings. Tighten all parts

as you assemble them, unless instructed to do

otherwise.

ASSEMBLY REQUIRES THE FOLLOWING TOOLS

(not included): two (2) adjustable wrenches, one (1)

phillips screwdriver, one (1) hammer, one (1)

power drill with a 1/16 drill bit and a 1/4 drill bit.

Soapy water.

You will also need some silicone to apply to the screw

heads before installing the end caps. (optional)

Bottom Mount Cover Lifter - Operation

To remove the cover from the spa, fold the spa

cover (at the hinge) back over the upper cover

support arm.

Then, using your foot, step down upon the lower

cover support arm while holding onto the foam

padded upper support arm and the cover will lift up

and be placed behind the spa.

Bottom mount cover lifter - Parts list

(CRS 1)

Description

1. #2 Screw

2. Mounting bracket

3. Pivot arm 1/2” x 43” (13 x 1092mm.)

4. Pivot bolt

5. Metal washers

6. Locknut

7. Spacer block

Qty

Parts List

Description

8. Upper cover support arm 1/2” x 41” (13 x 1041mm.)

9. Lower cover support arm 1/2” x 41” (13 x 1041mm.)

10. Coupler

11. Screw end cap

12. #1 Screw

13. Corner foam

Qty

Screw guide

Bottom mount bracket

screws in cm

Bottom mount screw in

inches

Self tapping screw in cm Self tapping screw in

inches

To assemble & install:

1. Position the spa cover (in closed position) on the spa,

making sure that all four corners are properly positioned

and square on the spa.

2. Insert the side pivot bolts and a metal washer into the

mounting brackets. (Figure 1). Using the #1 screws,

attach the left and right mounting brackets to the

appropriate sides of the spa. Position bracket ﬂush to

panel and 5” or 125 mm. from bottom of corner panel.

(See Figure 2.)

3. Connect the side pivot arms to the mounting brackets.

Attach the side pivot arms to the mounting brackets

with two spacer blocks, a metal washer, and a locknut.

Secure the bolt tightly on the back side of the

mounting bracket. Repeat this procedure for each

side. (See Figure 3.)

4. Slide two of the foam tubes on the corners of the

lower cover support arms (See Figure 4A). TIP: Try

dipping the foams in soapy water ﬁrst to help installation.

Insert the long ends of the lower cover support arms into

both sides of the coupler piece and then slide the lower

cover support arms into the shorter of the side pivot

arms on each side (See Figure 4.)

5. Slide two of the foam tubes to the corners of the upper

cover support arms. Then slide the long end of the

upper cover support arms into either side of the

coupler piece and then slide the short end of the upper

cover support arms into the top of the side pivot arms.

(See Figure 5.) Note: The upper cover support arms and

the coupler will now be laying on top of the spa cover

along the fold.

6. Adjust and center the coupler piece and upper support

arms so that the coupler piece is lying parallel

(approximately 0.5”(13mm.) away from the lifter to the

spa cover’s hinge).

7. Once you have the lifter ﬁtted to the size of your spa, use

the #2 screws to connect the arms together

Using the #2 screws, fasten support arms to the

coupler pieces. There will be six screws inserted into

each of the coupler pieces, three at each end.

There will be three screws inserted into each upper

cover support arm where it connects to the side

pivot arm and two screws inserted into the lower

cover support arms where they attach to the side pivot

arm. Use a touch of silicone on top of the screws to

apply the screw head covers on each screw

(See Figure 6.)

Note: Be sure to rotate the coupler Piece so that the

inserted screws are at a horizontal angle with the heads

facing the back of the spa.

Bottom mount cover lifter - instructions

(CRS 1)

Figure 1 Figure 4

Figure 4A

Figure 2

Figure 5

Figure 3

Slip the coupler

over the Lower

Cover Support Arm

Slip the coupler

over the lower

cover support arm

Figure 6

Three screws

on each side

of coupler

Two screws

on each side

of lower

support arms

Three screws

on each side

of lower

support arms

Three screws

on each side

of coupler

Bottom mount cover lifter

Quick assembly guide & Warranty (CRS 1)

Canadian Spa Company meets ISO 9001 Standards

When you purchase a hot tub from Canadian Spa Company, the

ISO 9001 certiﬁcation assures world class excellence in

manufacturing and customer service.

24 MONTH WARRANTY

Canadian Spa Company warrants this product to be free from

defects in workmanship and material, under normal use and

service conditions, for a Limited Lifetime Warranty.

This warranty extends only to the original purchaser.

Canadian Spa Company obligation under this warranty is

limited to replacing or repairing, at Canadian Spa Company

option, the product at one of its authorized service centers.

All products for which warranty claim is made must be

received by Canadian Spa Company at one of its authorized

service centers with all freight and other transportation charges

prepaid, accompanied by sufﬁcient proof of purchase.

All returns must be pre-authorized by Canadian Spa Company.

This warranty does not extend to any product or damage to a

product caused by or attributable to freight damage, abuse,

misuse, improper or abnormal usage or repairs not provided

by a Canadian Spa Company authorized service center, prod-

ucts used for commercial or rental purposes, or products used

as store display models.

No other warranty beyond that speciﬁcally set forth above is

authorized by Canadian Spa Company.

UK Ofﬁce:

Canadian Spa Company

Canada House

Salbrook Road

Salfords, Redhill

Surrey, RH1 5GL, UK

T: +44 1293 824094

F: +44 1293 824750

www.canadianspacompany.co.uk

France Ofﬁce:

Canadian Spa Company sarl

2 rue de la Moudrerie

27370 La Saussaye

France

T: +33 235 775 331

www.canadianspacompany.fr

Germany Ofﬁce:

Canadian Spa Company GmbH

Lutzerathstrasse 127

51107

Koln

Germany

T: +49-2203-995580

www.canadian-whirlpools.de

US Ofﬁce:

Canadian Spa Company

6848 Airport Rd

W Jordan Utah

84084

T: +1 (801) 696-5677

www.canadianspacompany.com

North America Head Ofﬁce:

Canadian Spa Company

99 Bronte Road, Suite 613

Oakville, Ontario

L6L 3B7

Canada

T: +1-877-347-7727

F: +1 (905) 825 2513

www.canadianspacompany.ca

Dubai / Middle East Ofﬁce:

Canadian Spa Company

JAFZA 8, Ofﬁce no.27

P. O. Box 26455

Dubai, UAE

T: + 9714 - 8815223

F: + 9714 - 8815224

www.canadianspacompany.co.uk

Screw in screws to location 1 Screw in screws to location 2 Finished ground support arm Assemble top support Finished top support

Top & botton support

conﬁguration

Insert top arm support Line up top support .5” (13mm)

away from centre seam

Screw in side arms using self

tapping screws

Screw in centre coupler - at

a horizontal angle with screw

heads facing the back of the spa

Ensure bracket is level on both

sides

Mark drill holes & drill with

# 8 drill & screw brackets to

cabinet

Install pivot arm using nut,

blocks and washers

Slide on two foam grips &

assemble ground support arm

Add self tapping screws

07/06/13

Otros manuales de Jacuzzi de Canadian Spa

Canadian Spa

Canadian Spa Vancouver UV Spa KH-10032 Manual de usuario

Canadian Spa

Canadian Spa KH-10030 Manual de usuario

Canadian Spa

Canadian Spa grand rapids Manual de usuario

Canadian Spa

Canadian Spa Alberta UV Spa Manual de usuario

Canadian Spa

Canadian Spa Calgary TP500 Manual de usuario

Canadian Spa

Canadian Spa Okanagan Manual de usuario

Canadian Spa

Canadian Spa Okanagan Manual de usuario

Canadian Spa

Canadian Spa Kingston UV Spa Manual de usuario

Canadian Spa

Canadian Spa Yukon TP500 Manual de usuario

Canadian Spa

Canadian Spa KELOWNA Manual de usuario

Canadian Spa

Canadian Spa Kelowna Spa KH-10041 Manual de usuario

Canadian Spa

Canadian Spa Thunder Bay UV Spa KH-10030 Manual de usuario

Canadian Spa

Canadian Spa GS Series Manual de usuario

Canadian Spa

Canadian Spa MUSKOKA SPA Manual de usuario

Canadian Spa

Canadian Spa St Lawrence 16' Swim Spa Manual de usuario

Canadian Spa

Canadian Spa BP Series Manual de usuario

Canadian Spa

Canadian Spa KP-10008 Manual de usuario

Canadian Spa

Canadian Spa London UV Spa KH-10131 Manual de usuario

Canadian Spa

Canadian Spa YUKON SPA Manual de usuario

Canadian Spa

Canadian Spa Rio Grande Manual de usuario

Canadian Spa

Canadian Spa Muskoka Manual de usuario

Canadian Spa

Canadian Spa St Lawrence 13' Swim Spa Manual de usuario

Canadian Spa

Canadian Spa Erie SE Spa KH-10130 Manual de usuario

Canadian Spa

Canadian Spa ERIE SE GL Manual de usuario

Manuales populares de Jacuzzi de otras marcas

Bestway

Bestway Lay-Z-Spa 54189 Manual de usuario

Jacuzzi

Jacuzzi ARGA ARG101C0110 Manual de lista de piezas

Morphy Richards

Morphy Richards Essentials PC4006 Manual de usuario

Softub

Softub PRESTIGE Manual de usuario

JNJ SPAS

JNJ SPAS SPA-318 Manual de instalación

KIRAMI

KIRAMI Comfort Family Manual de usuario

QCA Spa

QCA Spa VS501 PAK (VL260 TOPSIDE) Manual de usuario

HoMedics

HoMedics FB-655HJ-GB Manual de usuario

Everyday Hot Tubs

Everyday Hot Tubs 530 Manual de usuario

anko

anko SS-601A Manual de usuario

Jacuzzi

Jacuzzi Duetta 6042 Manual de usuario

Pooli

Pooli OS030979B Manual de usuario

Jacuzzi

Jacuzzi alimia Manual de usuario

ab Solares Smart Spa Manual de usuario

CalderaSpas

CalderaSpas CalderaSpas Utopia Series Manual de usuario

Outsunny

Outsunny 848-047V70 Manual de usuario

Aquatic

Aquatic INFINITY 1 Manual de usuario

Master Spas

Master Spas MP Force Manual de usuario