CamTron CTCD-536 Manual de usuario
High Resolution Color Dome Camera
1
INFORMATION - This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules & CE Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
◆
Do NOT use power sources other than those specified.
◆
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and
should conform to all local codes.
The lightning flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
■Contents
2
High Resolution Color Dome Camera High Resolution Color Dome Camera
3
Camera Operation 14
■Settings 15
■EXIT 27
ㆍLENS 16
ㆍSHUTTER 18
ㆍWHITE BALANCE 19
ㆍ BLC (Back Light Compensation) 20
ㆍAGC (Auto Gain Control) 21
ㆍADJUST 22
ㆍFUNCTION 23
- CAMERA ID 23
- DAY & NIGHT 24
- MIRROR 25
- MOTION DETECTION 25
- PRIVACY 26
- GAMMA 26
- LANGUAGE 27
- RESET 27
- RETURN 27
Specifications 30
Troubleshooting 28
Features
Warnings and Precautions
Names and Functions of Parts
Dimensions
Installation
Cable Connection
■Lens
■OSD
■VBS-EXTRA
■3 Axis Bracket
4
5
9
11
12
13
10
10
11
11
Components 8
■Features
Warning ■
The camera requires periodic inspection.
Contact an authorised technician to carry out the inspection.
Stop using your camera when you find it malfunctioning.
If the camera emits smoke or is unusually hot for a long period,
a fire may be caused.
Do not Install the camera on a surface that can not support it.
If the camera is installed on an inappropriate surface, it may fall
and cause injury.
Do not hold plug with wet hands.
It could cause an electric shock.
Do not dis-assemble the camera.
It may result in an electric shock or other hazards.
Do not use the camera close to a gas or oil leak.
It may result in a fire or other hazards.
4
High Resolution Color Domw Camera High Resolution Color Dome Camera
5
Horizontal Resolution of 540 TV
Lines
Clear image quality has been achieved by
employing a SONY CCD with 410,000
(effective) pixels, which provides a
horizontal resolution of 520 TV lines.
Electronic IRIS
The electronic IRIS function enables
continuous automatic control of the
shutter between 1/60(50)~1/100,000 seconds.
PRIVACY Function
The PRIVACY function conceals the
areas not required to appear on
the image.
High Sensitivity
The built-in high sensitivity SONY COLOR
CCD enables a clear image even at
0.3Lux (0.1Lux B/W)
Programmable GAMMA Processing
Controlled by OSD Menu
The camera functions are controlled by
selecting text displayed on the monitor
screen.
Additional Functions
MOTION DETECTION, MIRROR,
SHARPNESS and COLOR ADJUST
functions are also available.
■Precautions
Do not install the camera in
extreme temperature conditions.
Do not install the camera under
unstable lighting conditions.
Do not touch the front lens of the
camera.
Only use the camera under conditions
where temperatures are between
-10˚C and +50˚C. Be especially
careful to provide ventilation when
operating under high temperatures.
It can cause the image quality to be
poor.
Severe lighting change or flicker can
cause the camera to work improperly.
This is one of the most important parts of
the camera. Be careful not to leave
fingerprints on the lens cover.
Do not install or use the camera in an
environment where the humidity is high.
ㆍIf the camera is exposed to spotlight or object reflecting strong light,
smear or blooming may occur.
ㆍPlease check that the power satisfies the normal specification before
connecting the camera.
It can cause malfunctions to occur.
If it gets wet, wipe it dry immediately.
Liquids can contain minerals that
corrode the electronic components.
If exposed to radioactivity the CCD
will fail.
It can damage the CCD.
Do not drop the camera and protect
it from physical shocks.
Do not expose the camera to rain
or spill beverage on it.
Do not expose the camera to
radioactivity.
Never keep the camera pointed
directly at strong light.
6
7
High Resolution Color Dome Camera High Resolution Color Dome Camera
■Components Names and Functions of Parts ■
1. COLOR DOME CAMERA
2. SCREWS
3. WIRE FOR VBS-EXTRA
4. INSTRUCTION GUIDE
8
9
High Resolution Color Dome Camera High Resolution Color Dome Camera
■Names and Functions of Parts Names and Functions of Parts ■
Dimensions ■
②OSD PCB
●
●SET button : Used for the menu display. This button can be used to
confirm settings after changing the value of the selected function or
current conditions.
●
●UP & DOWN buttons : Used for selecting items by moving the cursor
up or down on the menu screen.
●
●LEFT & RIGHT buttons : Used when changing item values, by moving
the cursor to the left or right on the menu screen.
①LENS : Vari-Focal DC Auto Iris Lens
10
11
High Resolution Color Dome Camera High Resolution Color Dome Camera
③VBS-EXTRA FOR CONNECTING TO LCD
Please use the supplied wire when connecting to LCD
④SMPS PCB FOR DUAL POWER - IF APPLICABLE
VBS-EXTRA
⑤3 AXIS BRACKET
Please loosen screws and fix tilted and panned position.
(unit : mm)
DOWNUPSETRIGHTLEFT
■Installation
Cable Connections ■
1. Dome Base Mounting
- Open the dome cover by loosening the 3 screws using the special
wrench provided.
- Mount the base of camera to a sturdy surface using the 4 screws (1.5
inch) and the 4 premade holes on the base of the dome.
2. Power Connection & Monitor Impedance
- DC12V/300mA regulated power supply (DC12V only)
AC24V Class 2 power supply (AC24V/DC12V)
-
To avoid fire or shock hazard, always use a CE & FCC listed power supply.
- Set the monitor impedance switch to 75Ω. Check the impedance
switch if the screen appears blurred.
3. Camera Module Adjustment
- Loosen screws for the 3-axis camera bracket to adjust the cameras
angle of view.
- Make sure to retighten the camera bracket screws.
- Use the OSD buttons to select the different camera functions.
4. Dome Cover Mounting
- Replace the dome cover to the base and tighten the 3 screws.
12
13
High Resolution Color Dome Camera High Resolution Color Dome Camera
DC only
AC AC IN AC IN
■
Camera Operation
14
High Resolution Color Dome Camera High Resolution Color Dome Camera
15
■
Menu
SETUP menu
LENS (selection)
SHUTTER
(
condition and speed control)
WHITE BALANCE control
BLC
(Back Light Compensation)
AGC (Auto Gain control)
ADJUST
FUNTION
EXIT
ㆍMANUAL ㆍDC/VIDEO
ㆍFIXED ㆍAUTO ㆍFLK
ㆍATW
ㆍMANUAL
ㆍAWB ㆍFIXED
ㆍBLC AREA ㆍBLC RATIO
ㆍAGC CONTROL
ㆍCONTRAST ㆍCAMERA ID
ㆍCR
-
GAINㆍCB
-
GAIN
ㆍRETURN ㆍCAMERA ID
ㆍDAY / NIGHT ㆍMIRROR
ㆍMOTION ㆍPRIVACY
ㆍGAMMA ㆍLANGUAGE
ㆍRESET
Settings can be made using the 5 buttons located in the camera.
1. Press the SET button
ㆍSettings can now be made. The SETUP menu is displayed on the monitor.
2. Select a menu item from the list available by using the UP and DOWN
buttons.
ㆍ
Funtions are selected using up and down buttons.
ㆍ
The selected position is displayed in blue.
■
Settings
SETUP
LENS DC
SHUTTER FIXED
WHITE BAL. ATW
BLC OFF
AGC ON
ADJUST
FUNCTION
EXIT
DOWNUPSETRIGHTLEFT
Note
SETUP
LENS DC
SHUTTER FIXED
WHITE BAL. ATW
BLC OFF
3. Press the LEFT or RIGHT button to change modes.
ㆍWhen the LEFT or RIGHT button is pressed, available values and modes
are displayed in order. Keep pressing the button until you get to the
mode you wish to select.
4. Select 'EXIT' and then press the SET button to exit the set up menu.
This function is used to adjust the brightness of the screen.
1. When the SETUP menu is displayed on the screen, position the cursor to point
to 'LENS' by using the UP and DOWN buttons.
2. Select the type of the lens setting to use by pressing the LEFT or RIGHT button.
LENS (selection)
ㆍIf appears at the mode selected, it means that there is a sub-menu
which can be selected by pressing the SET button.
●DC : Auto Iris Lens selection
●MANUAL : Manual Lens selection
3. Press the SET button to return to the previous menu.
Note
ㆍThe brightness of the screen can be adjusted in DC mode. The
brightness can be adjusted within the range of 0 ~255. The optimum
level of brightness can be achieved using this adjustment.
SETUP
LENS DC
SHUTTER FIXED
WHITE BAL. ATW
BLC OFF
AGC ON
ADJUST
FUNCTION
EXIT
Modes can be changed
using the LEFT and
RIGHT buttons.
Select the desired
menu item by
using the UP and
DOWN buttons.
LENS DC
: RETURN
BRIGHTNESS 093
■
Camera Operation
16
High Resolution Color Dome Camera High Resolution Color Dome Camera
17
SETUP
LENS MANUAL
SHUTTER FIXED
WHITE BAL. ATW
BLC OFF
■
Camera Operation
18
High Resolution Color Dome Camera High Resolution Color Dome Camera
19
Auto or manual control can be selected.
1. When the SETUP menu is on the screen, position the cursor to point to
'SHUTTER' by using the UP and DOWN buttons.
2. Select the shutter mode by pressing the LEFT or RIGHT button.
●FLK : Select 'FLK' mode when flickering occurs on the screen
due to an imbalance between illumination and frequency.
NTSC Model:1/100, PAL Model: 1/120
●AUTO : Automatic control of the shutter speed is enabled.
When AUTO mode is on, the shutter speed is controlled
automatically according to the brightness of the scene.
●FIXED : The shutter speed can be controlled manually.
●MANUAL mode (256 steps) :
There are 256 pre-defined electronic shutter speeds in manual mode
available for selection; set according to environment conditions.
3. Select 'FIXED' mode for manual shutter speed adjustment.
ㆍ
Selectable speeds are from '1/60' to '1/120,000'sec (NTSC) and '1/50'
to '1/120,000'sec (PAL).
4. Press the SET button when the settings are completed.
SHUTTER (condition and speed control)
The screen colours can be adjusted using the WHITE BALANCE function.
1.
Position the cursor to point to 'WHITE BAL' on the SETUP menu by using the
UP and DOWN buttons.
2. Select the mode you wish to adjust by pressing the LEFT or RIGHT buttons.
WHITE BALANCE
※Select one of the 4 modes below.
●
ATW
(Auto Tracking White Balance) : This mode can be used within the
colour temperature range 1,800˚K~ 10,500˚K(eg, fluorescent light, outdoor,
sodium vapour lamp etc.)
●
AWB(Automatic White Balance)
: Press the SET button while the
camera is directed at a piece of white paper to obtain the optimum state
under current illumination. If the environment, including the light source,
changes the white balance will need to be adjusted again.
●
MANUAL : The manual adjustment mode enables finer adjustment.
Select ATW or AWB first then change to manual adjustment mode and
press the SET button. Set the appropriate colour temperature then increase
/ decrease the red and blue colour values and monitor the color
changes of the object.
●
AWB FIXED optimized at 2100˚K
MODE1 : 2680˚K ((No light source)
MODE2 : 3200˚K
MODE3 : 5500˚K (Fluorescent light source)
MODE4 : 5100˚K
SETUP
LENS MANUAL
SHUTTER AUTO
WHITE BAL. ATW
BLC OFF
AGC ON
ADJUST
FUNCTION
EXIT
Tabla de contenidos
Otros manuales de Cámara de seguridad de CamTron
