Campbell SkyVUE 8 Manual de usuario

SkyVUE 8 Ceilometer

Part Number 003444

Revision: 02/2022

www.campbellsci.com/skyvue8

1. Introduction

Thank you for purchasing the SkyVUE 8. The SkyVUE

8 provides data valuable for your application.

NOTE:

This Quick Deploy Guide is an overview of the

steps required to make this system operational.

Detailed siting, installation, and software

information is available from the user manual on

the Campbell Scientific website. Use the QR code

or type www.campbellsci.com/skyvue8 to

access the web page.

2. Warnings

lDo not modify the SkyVUE 8 because it can

damage the unit and expose users to

dangerous light levels and voltages.

lDo not attempt to repair the SkyVUE 8 unit

without consulting Campbell Scientific.

lRemoving the laser module connected to

power may expose the user to hazardous class

3B laser radiation.

lDo not operate the laser module while it is

outside the housing.

lAnnually, check the laser warning label to

ensure it is visible and can be clearly read.

lSkyVUE 8 ceilometers are classified as 1M. This

classification means the naked eye can safely

view the beam but looking directly into the

beam with optical instruments, such as

binoculars, can be dangerous. When installing

the sensor, avoid pointing the laser housing

towards areas where binoculars are often

used.

lUse of controls, adjustments, or procedures

other than those specified herein may result in

hazardous radiation exposure.

lBecause of hazardous mains voltages, only

qualified personnel should wire the power

supply. Permanent outside installations usually

require a certified electrician who is familiar

with local electrical and safety legislation.

lRemoval of electronic module covers or

connectors while the unit is powered will

expose the operator to potentially hazardous

voltages and may damage the sensor.

lWhen powered, the heaters may operate

automatically and without warning. They may

remain hot when not powered. Follow the

isolation precautions, to avoid shock and burn

hazards.

lThe laser begins operating as soon as the

battery is connected. Do not point the laser

where it can be viewed with magnifying optics.

lThis ceilometer meets UKCA and EU

declarations of conformity, citing international

standards applicable to the product.

3. Initial preparation and checks

Campbell Scientific recommends becoming familiar

with the SkyVUE 8 and performing the following

basic functionality checks before final deployment at

the installation site.

The SkyVUE 8 is shipped with the following; data

cable is not shown:

The power and data connectors are easily accessible

on the bottom of the unit and are clearly and

individually labeled.

Connect power supply:

1. Open the door.

2. Connect the battery.

3. Connect a suitable DC power supply.

4. Remove the desiccant pack placed in the

internal electronics area as this is only required

for shipping or storage purposes.

5. Find the green status LED by looking down the

ceilometer window. It should flash every 10

seconds. If the status LED is not flashing or is

flashing at a different rate, consult the user

manual or contact Campbell Scientific.

Configure and check two-way communication:

1. Connect the SkyVUE 8 USB port to a

computer.

2. Use a terminal emulation program to set

baud-rate settings to 115200 baud, 8N1

bits/parity. Once the data connection is

established, the SkyVUE 8 should output data

in ASCII text with alpha-numeric integer

values.

CAUTION:

If the message format is not ASCII text with

alpha-numeric integers, check the terminal

baud-rate settings and refer to the user

manual or contact Campbell Scientific.

3. Type Open 0 to open the terminal mode.

4. At the CS136> prompt, type Status.

5. Check the date/time information since it can

drift, and the clock battery can discharge,

especially if the unit has been in storage.

6. Type Close to exit the terminal mode. It will

close automatically after 10 minutes of

inactivity.

Disconnect the backup battery while transporting

the SkyVUE 8 to the installation site.

Consider downloading ViewPoint (demo version)

software, available at

www.campbellsci.com/downloads/viewpoint-2102 .

This software package can help familiarize users with

data configuration and visualization.

Otros manuales para SkyVUE 8

Otros manuales de Instrumento de medición de Campbell

Campbell

Campbell SI-111 Manual de usuario

Campbell

Campbell SR05 Manual de usuario

Campbell

Campbell CS526 Manual de usuario

Campbell

Campbell CS300 Manual de usuario

Campbell

Campbell HFP01 Manual de usuario

Campbell

Campbell OBS-3 Manual de usuario

Campbell

Campbell Q-7.1 Manual de usuario

Campbell

Campbell 110PV Manual de usuario

Campbell

Campbell VWIRE 305 Manual de usuario

Campbell

Campbell TDR100 Manual de usuario

Campbell

Campbell Weatherpak M Manual de usuario

Campbell

Campbell CR7 Manual de usuario

Campbell

Campbell CS650 Manual de usuario

Campbell

Campbell WindSonic1 Manual de usuario

Campbell

Campbell TDR100 Manual de usuario

Campbell

Campbell EC155 Manual de usuario

Campbell

Campbell CR10XTCR Manual de usuario

Campbell

Campbell CS110 Manual de usuario

Campbell

Campbell CS616 Manual del propietario

Campbell

Campbell CS106 Manual de usuario

Campbell

Campbell SR20-D2 Manual de usuario

Campbell

Campbell CSAT3BH Manual de usuario

Campbell

Campbell CS300 Manual de usuario

Campbell

Campbell HMP45C Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario