CAME TRA08 Manual de usuario

COMPLETE SYTEM FOR RADIO COMMANDS

INSTALLATION MANUAL

TRA08

119RU01EN

2- Manual code

119R

119 R

U01

EN v.

2- 03/2016 - © Came S.p.A. The contents of this manual may be revised at any time, and without notice.

2.1 Intended use

Legend of symbols

This symbol shows parts which must be read with care.

This symbol means the parts which describe safety issues.

This symbol tells you what to tell the end-user.

The TRA08 kit is for commanding, only by radio, up to four different operators.

Any installation and use other than that specified in this manual is forbidden.

Engineered and built entirely by CAME S.p.A.

The kit comprises:

- 1 RBE42: 230 V outdoor four-channel radio receiverV.

5 A relay.

- 2 TOP-434EE : four-channel transmitters;

- 1 TOP-A433N: antenna with fastening bracket;

-1TOP-RG58: co-axial antenna cable (5 m).

One radio command to control four systems:

- arm the alarm;

- turn on outdoor lights;

- turn on the lawn sprinkler system;

- close the shutters.

"IMPORTANT INSTALLATION SAFETY INSTRUCTIONS"

“WARNING: IMPROPER INSTALLATION MAY RESULT IN SERIOUS HARM. PLEASE FOLLOW ALL INSTALLATION INSTRUCTIONS”

“THIS MANUAL IS INTENDED ONLY FOR PROFESSIONAL INSTALLERS OR OTHER COMPETENT INDIVIDUALS”

2.1 Intended use

4 Description

5.1 Preliminary checks

5.2 Tools and equipment

Cut off the main power before acting inside the equipment.

• Do not install multiple receivers at less than 4-5 m from each other, to prevent functioning anomalies

• The receiver must always be ﬁtted with an antenna. Possibly place the antenna as high as possible from the ground and far from

any metal and reinforced concrete structures.

Make sure you have all the tools and materials needed to carry out the installation in total safety and in accordance with

current regulations. Here are some examples.

5 Installation

CAME

75 mm

87 mm

115 mm

225 mm

180 mm

3- Manual code

119R

119 R

U01EN

U01EN v.

2- 03/2016 - © Came S.p.A. The contents of this manual may be revised at any time, and without notice.

TECHNICAL DATA

Power supply 230V A.C.

Insulation class

Material ABS

Protection rating IP54

6.1 Dimensions

4-channel outdoor radio receiver.

The board is powered by 230 V AC.

For each single output you can select the following features :

- maintained action command;

- bistable (switch);

- fixed 3 second timed monostable”;

- fixed 5 minute timed monostable’.

Warning! Cut off the main power before acting inside the equipment.

6 RBE42

6.2 Main components

1. Control unit fuse (315 mA - quick)

2. Buttons to memorise radio code

3. Line fuse (125 mA - quick)

4. 230 V power supply terminals

5. Memorisation underway LED

6. AF43S radio-frequency card

7. Functions selection Dip switch

8. Antenna connection terminals

9. Systems connection terminals (relay

rated max: 10A)

4- Manual code

119R

119 R

U01

EN v.

2- 03/2016 - © Came S.p.A. The contents of this manual may be revised at any time, and without notice.

7 TOP-434EE

Multi-user channel transmitter

TECHNICAL DATA

Frequency AM 433.92 MHz

Batteries two CR2016 - 3 V DC

Lithium

Power draw when transmitting 12 mA

Effective to 50 ÷ 150 m

Code combination 4096

Weight 16 G

8 TOP-433N

8.1 Main components

1. Antenna rod

2. Upper container part

3. Circuit

4. Lower container part

5. Antenna/ bracket fastening screws

6. Fastening bracket

8.2 Mounting description

• Fasten the lower part of the container to

the anchoring bracket - use the supplied

screws;

• connect the RG58 coaxial cable to the

antenna circuit;

• insert the circuit into the lower part of the

container trough the apposite hole on the

circuit itself;

• ﬁt the two containers together and screw

in the shaft.

Connect RG58 antenna cable to the apposite terminals.

9 Activating the radio command

Antenna

Red LED signal light

Cable grip Cable

AF43S

RG58

TOP-A433N

5- Manual code

119R

119 R

U01EN

U01EN v.

2- 03/2016 - © Came S.p.A. The contents of this manual may be revised at any time, and without notice.

Radio frequency card

Plug in the radio-frequency card onto the electronic board AFTER CUTTING OFF THE MAIN POWER SUPPLY (or disconnecting

the emergency batteries).

N.B.: The electronic card recognises the radio-frequency card only when it is powered up.

Basic Card

AF card

10 Electrical connections

• Connect the devices to command onto the 4 outputs, selecting the feature you want for each one;

• connect the antenna onto the relative terminal with the RG58 cable (see p. 4);

• power the card with a 230 V line

selecting functions *

Power supply

230 V A.C.

to the devices to be comman-

ded (max. power 250 V AC, with

inductive load)

1 2 3



/&&





/&&





/&&



/&&

6- Manual code

119R

119 R

U01

EN v.

2- 03/2016 - © Came S.p.A. The contents of this manual may be revised at any time, and without notice.

"Maintained action" feature : the relay action lasts as long as the transmitter button is pressed .

Fixed 3 second timed monostable”: once the transmitter button is released the relay action lasts 3

seconds.

Bistable (switch): repeatedly pressing the transmitter button will turn on and off the relay conti-

nuously as if it were a switch.

Fixed 5 minute timed monostable: once the transmitter button is released the relay action lasts 5

minutes.

* 10.1 Selecting functions (for each single output)

11 Duplicating a transmitter

Duplication must be done because each of the transmitters is made with different codes.

1. Simultaneously press the two buttons until the LED ﬂashes more quickly;

2. 2 - now press the button you wish to activate (the LED lights up);

3. with 10 seconds, rest the active transmitter against it back part and press the button that needs duplicating for a few seconds.

Once memorisation is complete, the LED will flash 3 times and the transmitter will be ready for use.

Repeat points 1, 2 and 3 for the remaining buttons.

12 Memorising the code onto the receiver

Keep memorisation button pressed until the LED flashes, press the transmitter button to send the code.

The LED will stay ON to confirm memorisation is OK.

Perform the same procedure for each exit (also see examples on the following pages).

1=> OUT1

2=> OUT2

3=> OUT3

4=> OUT4

LED signal light

radio code

P1 => 1 => OUT1 P2 => 2 => OUT2

P3 => 3 => OUT3 P4 => 4 => OUT4

CAME

P3 P4

7- Manual code

119R

119 R

U01EN

U01EN v.

2- 03/2016 - © Came S.p.A. The contents of this manual may be revised at any time, and without notice.

Apartment block barrier

Timed walkway lights

Timed entrance-stairs lights

Sectional door to garage zone

13 Application example

www. came.com

CAME S.p.A.

Via Martiri Della Libertà, 15 Via Cornia, 1/b - 1/c

31030

Dosson di Casier

Treviso

Treviso - Italy

33079

Sesto al Reghena

Pordenone

Pordenone - Italy

(+39) 0422 4940

(+39) 0422 4941

(+39) 0434 698111

(+39) 0434 698434

English

English - Manual code

9RU01EN

9RU01EN v.

The contents of this manual may be revised at any time, and without notice.

14 Dismantling and disposal

15 Compliance statement

Declaration - Came S.p.A. declares that this device conforms with the essential requirements and other pertinent provisions

established by directive 1999/5/CE

An original copy is available on request.

CAME S.p.A. employs a UNI EN ISO 14001 certified and compliant environmental protection system at its plants, to

ensure that environmental safeguarding.

We ask you to keep protecting the environment, as CAME deems it to be one of the fundamental points of its market operations

strategies, by simply following these brief guidelines when disposing:

DISPOSING THE PACKING MATERIALS

The packing components (cardboard, plastic, etc.) are solid urban waste and may be disposed of without any particular

difficulty, by simply separating them so that they can be recycled.

Before actions it is always advisable to check the pertinent legislation where installation will take place.

DO NOT DISPOSE OF IN NATURE!

DISPOSING OF THE PRODUCT

Our products are made using different types of materials. The majority of them (aluminium, plastic, iron, electric cables) can be

considered to be solid urban waste. They may be recycled at authorised firms.

Other components (electrical circuit board, remote control batteries etc.) may contain hazardous waste.

They must, thus, be removed and turned in to licensed firms for their disposal.

Before acting always check the local laws on the matter.

DO NOT DISPOSE OF IN NATURE!

Otros manuales para TRA08

Tabla de contenidos

Otros manuales de Receptor de CAME

Manuales populares de Receptor de otras marcas

Garmin

Garmin GA 23 Manual de usuario

Aiphone

Aiphone PS-12F Manual de usuario

IMES

IMES TCS-01CA-PMI Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR Manual

AMIMON

AMIMON AMN12310 WHDI Manual de usuario

Dual

Dual DMCPA79BT Instrucciones de funcionamiento

Sound Associates

Sound Associates SA652P Manual de usuario

Sherwood

Sherwood NewCastle R-772 Manual de usuario

Audio

Audio A10-RX Series Manual de usuario

AllSee

AllSee PushShare PSRV1.1 Manual de usuario

DEMAG

DEMAG DRC-DR D2 Manual de usuario

Teleco

Teleco TVRCL868A02 Manual de usuario

Bosch

Bosch RF3222E Manual de usuario

Kramer

Kramer 631R Manual de usuario

Xpress

Xpress xmc10 Manual de usuario

JVC

JVC KD-MR1BTS Manual de usuario

Omega Engineering

Omega Engineering UWTC-REC3 Manual de usuario

e-survey

e-survey E300 Pro Manual de usuario