CAME QBESetUp Manual del propietario
Application for programming
radio and Wi-Fi devices
QBESetUp
PROGRAMMING MANUAL
EN
English
FA01251-EN
Single network configuration Wi-Fi
Dual network configuration LAN or LAN/Wi-Fi
1 2 3
1
2
34
Single network configuration Wi-Fi
Dual network configuration LAN or LAN/Wi-Fi
1 2 3
1
2
34
Page2- Manual FA01251-EN - 04/2019 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Double network configuration (LAN or LAN / Wi-Fi)
Single network configuration (Wi-Fi)
1 - Connect the device to your PC (router, switch) using the Ethernet cable supplied, access the web page of
the device, configure the LAN and the Wi-Fi network.
2 - Use the "QBESetUp" application to configure the system.
3 - Use the "QBE User" application to access the system.
4 - Register the device to CAMEConnect.
1 - Use the "QBESetUp" application to configure the system.
2 - Use the "QBE User" application to access the system and configure the Wi-Fi network.
3 - Register the device to CAMEConnect.
SETTING THE DEVICE NETWORK PARAMETERS
The network parameters can be set from the configuration web page or through the user APP.
The device leaves the factory with the following network configuration:
- IP address on LAN: 192.168.1.80
- WiFi address: 192.168.9.1 (in Access Point mode with name "QBE_0x73xxxx")
Page3- Manual FA01251-EN - 04/2019 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Establishing connection to QBE
1 - Press the button to start the search for available
on-line devices
4 - Choose the device you want to connect to.
5 - If the device cannot be directly reached it is
possible to manually enter the IP address.
Main Homepage commands
1 - It allows connection to an available QBE (ON-
LINE)
2 - It opens an installation previously created and
saved on the device (OFF-LINE)
3 - It allows access to the configuration pages of a
new system without necessarily being connected
to the network (OFF-LINE).
APP USE
Launch the application.
A
B
C
D
E
Page4- Manual FA01251-EN - 04/2019 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Work area description
1 - It saves the system
2 - It opens a previously saved system structure
3 - It allows access to the system map view config-
uration
4 - It filters the system structure view
5 - It allows to share the system structure
6 - It shows the icon representing the QBE in the
middle of the work area
7 - It removes all devices connected to QBE
8 - It opens the section dedicated to diagnostics
9 - It view the list of active services
10 - It allows to return to the main software page
11 - Icon representing the QBE.
Creating a new system
A
B
C
D
E
F
G
H
I
J
K
Page5- Manual FA01251-EN - 04/2019 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
2 - It allows access to the search screen of the
home automation modules available on-line.
1 - It allows access to the connected devices search
functions.
Adding home automation modules to the system structure (on-line mode)
Accessing the QBE functions menu
Functions menu commands
Press and hold the icon representing QBE until the
function menu appears.
1 - Name assigned to the device.
2 - It adds a device to the system structure
3 - It allows access the to the device's configuration
options.
4 - It opens a list of the modules to which the device
can connect
5 - Program the device
6 - It allows access to the connected devices search
functions.
Icon on Green background = Device connected
Icon on Blue background = Device not connected
Icon on Orange background = Programming in
progress
Icon on Red background = Programming failed
Icon on Violet background = Unreachable device
A
B
C
D
E
F
A
B
Page6- Manual FA01251-EN - 04/2019 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Manual search for connected devices
4 - Press the button to put the QBE device in
standby mode
Press the "SERVICE" button of the home automation
module to be added to the system.
The ID service of the device is sent to QBE.
The device is added to the system structure.
For OH/2O16WL modules it will be possible to
choose whether the module must be used for the
automation of shutters or with free exits.
Automatic search for connected devices
3 - It performs a network scan and compiles a list of
detected devices
Press the "+" button to insert the devices in the
structure.
C D
Page7- Manual FA01251-EN - 04/2019 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Select the type of device to be added to the system
structure.
Select the type of devices required.
1 - It adds a device to the system structure.
Adding home automation modules to the system structure (o-line mode)
A
Page8- Manual FA01251-EN - 04/2019 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Press the button that allows to add inputs or outputs
to the module.
Select the input/output to be added to the system
structure.
Adding inputs/outputs to the module
Press and hold the icon representing the connected
module until the function menu appears.
Functions menu commands
1 - It allows to add inputs or outputs to the module
2 - It allows to configure the module general
parameters
3 - It allows to manage the connections to the
module inputs and outputs
4 - It removes the module from the system structure
5 - It starts programming the module only
6 - It starts the programming of the module and of
the inputs/outputs connected to it
7 - It allows to assign a serial number (ID) to the
module choosing it from those available.
Accessing the functions menu of a connected module
A
B
C
D
F
F
G
Page9- Manual FA01251-EN - 04/2019 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Creating connections between the module
inputs and outputs
Press and hold the icon representing the output
1 - Press the button and choose, among those avail-
able, the input to be connected to the output.
The connection between the module inputs and
outputs can also be made by dragging the button
icon (input) above the light icon (exit) that it has to
command.
Repeat the operation to connect additional inputs to
the output.
Work area description
Icon on Green background = Device connected
Icon on Blue background = Device not programmed
Icon on Orange background = Programming in
progress
Icon on Red background = Programming failed
Icon on Violet background = Unreachable device
Blue dotted line = Radio connection
Green dashed line = Logical connection
Black continuous line = Wired connection
A
Page10 - Manual FA01251-EN - 04/2019 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Configuration window description
2 - Touch the area to manually enter the module
serial number.
3 - Touch the area to edit the module's name.
4 - Press the button to set the type of action that the
inputs connected to the output must perform.
Configuring the home automation module general parameters
Press and hold the icon representing the connected
module until the function menu appears.
1 - Press the button to access the module general
parameters configuration options.
A
B
C
D
Tabla de contenidos
Otros manuales de Sistema de intercomunicación de CAME
CAME
CAME BPT DVC/01 Manual del propietario
CAME
CAME FUTURAKITVC04 Manual de usuario
CAME
CAME KIT AGT V + LITHOS Manual de usuario
CAME
CAME XTS 7 WH WIFI Manual de usuario
CAME
CAME 001CS1PLCO Manual de usuario
CAME
CAME VK01 Manual de usuario
CAME
CAME AGT V Hoja de especificaciones
CAME
CAME 001DC01EARY Manual de usuario
CAME
CAME PLACO-C Manual de usuario
CAME
CAME AGT A200 Manual de usuario
CAME
CAME 001DC02EARY Manual de usuario
CAME
CAME AGTMTMVKIT Manual de usuario
CAME
CAME LVC/01 Manual del propietario
CAME
CAME PLACO-VC Manual de usuario
CAME
CAME BPT KIT FREE LVC Manual de usuario
CAME
CAME PLACO-VC Manual de usuario
CAME
CAME LHS A/01 Manual
CAME
CAME XTS 7 WH WIFI Manual
CAME
CAME XVP S Manual de usuario
CAME
CAME XTS 7IP BK WIFI Manual
