Cambium Networks E400 Manual de usuario

! !

Easy!extensions!of!WiFi!coverage!

cnPilot(Mesh(

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

ePMP1000!Hotspot,!cnPilot!E400,!

cnPilot!E500!

Cambium'Networks'Inc'

Table&of&Contents&

OVERVIEW' 2!

CONFIGURATION' 2!

MESH'WLAN' 4!

MESH'SECURITY' 4!

VLANS' 4!

RADIOS' 4!

STATUS' 5!

Overview&

cnPilot Enterprise series of WiFi access points support wireless mesh allowing the

user to easily extend the range of their network and to cover areas where a cable

run might be hard to do. Users can also mix and match device types, so a link is also

allowed between a cnPilot E400 AP and an ePMP1000 Hotspot. Mesh support was

added in software version 2.0.

Mesh links form between two radios at a time: a radio configured as a base will

operate like a normal AP right after it comes up. Ie. Its radio will beacon on startup

so its SSID can be seen by radios configured as mesh clients. The mesh-client radios

will scan all available channels on startup, looking for a base AP to connect with. The

base and client APs identify each other by a common SSID configured on both the

devices. When a base is detected, the client will associate with the base just as a

regular wireless client would. Once the association and any security handshake (for

instance with WPA2) completes, the APs start bridging packets across that link.

A radio that is configured for mesh can still service clients at the same time, the radio

does not have to be dedicated to mesh. Up to 5 such client radios can connect to a

base radio.

Configuration&

Mesh configuration is done in the Wireless-LAN context. When the user selects a

WLAN, one of the configuration items there is ‘Mesh’ which defaults to Off but can

be configured to one of Base or Client. The radio where this WLAN is mapped would

then act accordingly as a base or a client.

Once either of the two mesh options is selected, the rest of the WLAN configuration

items for this WLAN are hidden as they are not applicable, and the GUI will only

display the parameters applicable to mesh:

In the CLI the configuration commands are same as the ones used for WLAN. The

additional CLI command is to enable mesh inside the WLAN context.

(cnWest-E400)# wireless wlan 1

(cnWest-E400)# mesh client

Mesh&WLAN&

One Wireless LAN has to be dedicated to Mesh, and the SSID on that wireless LAN

will be used by the radios to identify each other and form the connection. The same

SSID should be configured on the radios used for mesh base as well as the one used

on mesh client. This SSID will only allow connections from mesh peers, regular

wireless clients will not be allowed to associate on such an SSID.

Additional WLANs can be configured on the radio if the radio would be required to

service other clients in addition to forming the mesh link.

Mesh&Security&

The Mesh link can be secured with WPA2-Preshared security, which provides AES

encryption. To configure security select ‘WPA2-Preshared-keys’ under ‘Security’, then

configure a passphrase between 8 to 63 characters long. The same configuration

should be done on both ends of the link (client and base).

VLANs&

The mesh link will bridge all packets across all VLANs on that access point. The Vlan

in the WLAN configuration page is the default vlan and should typically be configured

to the VLAN where the device has its primary IP address for management.

Radios&

The Wireless LAN configured for mesh would by default be mapped to the 5GHz radio

on dual radio devices, and this is the recommended configuration. However it is

possible to enable mesh on the 2.4GHz radio, or even both 2.4GHz and 5GHz radios

of an access point.

Given the 5GHz radio supports wider channels (80MHz), and much higher modulation

schemes (802.11ac data rates) the recommendation would be to use the 5GHz radio

for backhaul and to service clients using the 2.4GHz radio on the AP.

Status&

The mesh configuration status (off/client/base) of a radio is available in the

dashboard of the device GUI:

In addition, the status of each link with details such as the signal strength are also

seen on the device dashboard:

Otros manuales para E400

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Cambium Networks

Cambium Networks

Cambium Networks cnRanger Manual de usuario

Cambium Networks

Cambium Networks PMP 450i Manual de usuario

Cambium Networks

Cambium Networks E400 Manual

Cambium Networks

Cambium Networks ePMP 1000 Manual de usuario

Cambium Networks

Cambium Networks PMP/PTP 450 Series Manual de usuario

Cambium Networks

Cambium Networks cnWave Series Manual de usuario

Cambium Networks

Cambium Networks ePMP 3000 Series Manual de usuario

Cambium Networks

Cambium Networks XE5-8 Manual

Cambium Networks

Cambium Networks PMP 450 Series Cómo utilizar

Cambium Networks

Cambium Networks PTP 820G Manual de usuario

Cambium Networks

Cambium Networks XIRRUS XD2-230 Manual de usuario

Cambium Networks

Cambium Networks PTP 820 Series Manual de usuario

Cambium Networks

Cambium Networks PTP 550 Series Manual de usuario

Cambium Networks

Cambium Networks PMP 400 Series Manual de usuario

Cambium Networks

Cambium Networks cnWave V1000 Manual de usuario

Cambium Networks

Cambium Networks PTP 820 RFU-E Manual de usuario

Cambium Networks

Cambium Networks Force 110 Manual de usuario

Cambium Networks

Cambium Networks cnPilot e600 Manual de usuario

Cambium Networks

Cambium Networks XV3-8 Manual

Cambium Networks

Cambium Networks XV2-2T1 Manual

Cambium Networks

Cambium Networks cnPilot e501S Instrucciones de funcionamiento y mantenimiento

Cambium Networks

Cambium Networks PMP 450 Series Manual de usuario

Cambium Networks

Cambium Networks PMP 450 Manual técnico

Cambium Networks

Cambium Networks PTP 550E Series Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario