Calspas Avalon A726B Manual de usuario

out written consent is strictly prohibited.

Cal Spas®is a registered trademark.

Due to continuous improvement pro-

grams, all models, operation, and/or

specications are subject to change with-

out prior notice.

LTR20081024, Rev. B

6/12/08

CONTACT INFORMATION

For customer service, please contact

your authorized dealer immediately. If

you need additional information and/or

assistance, please contact:

L.M.S. Customer Service Department

1462 East Ninth Street

Pomona, CA 91766

Toll Free: 1-800-CAL-SPAS

Fax: 1-909-629-3890

www.calspas.com

Contents

Pre-Delivery and Installation Checklist ................................................ 1

Portable Spa Site Preparation............................................................... 4

In-Ground Spa Site Preparation............................................................ 4

Getting the Spa Into Your Yard.............................................................. 6

Electrical Requirements......................................................................... 8

Electrical Requirements – US and Canada....................................................... 8

Electrical Installation -- Europe ...................................................................... 13

Installing the In-Ground Shell ............................................................. 16

Equipment Pack Plumbing Connections (In-Ground Spas)............. 17

Plumbing Connections .................................................................................... 19

Electrical and Electronic Connection............................................................... 21

Pouring the Deck............................................................................................. 25

Spa Technical Specications .............................................................. 26

Pre-Delivery and Installation

Checklist

Most cities and counties require permits for exterior construction and

electrical circuits. In addition, some communities have codes requiring

residential barriers such as fencing and/or self-closing gates on property to

prevent unsupervised access to the property by children under the age of

5. Your dealer can provide information on which permits may be required

and how to obtain them prior to the delivery of your Cal Spa®.

We strongly recommend you have a qualied, licensed contractor perform

the installation of your in-ground or ported spa. The installation instructions

contained in the manual are for the use of a qualied contractor or

installer.

Consumers who choose to install their own in-ground spas bear sole

responsibility for any performance or warranty issues and may void portions

of their warranty as a result. For this reason, we strongly recommend they

hire an experienced professional for their installation.

For additional operating and installation information, please see your

selling dealer. To locate a dealer nearest you call 800-CALSPAS or visit

www.calspas.com.

Portable Spa

Pre-Delivery Checklist

Before Delivery

Plan your delivery route

Choose a suitable location

for the spa

Lay a 3” - 4” concrete slab

Install dedicated electrical

supply

After Delivery

Place spa on slab

Connect electrical

components

In-Ground Spa

Pre-Delivery Checklist

Before Delivery

Plan your delivery route

Choose a suitable location

for the shell and equipment

pack

Excavate the hole

Install dedicated electrical

supply

Install dedicated NG line for

gas heater

After Delivery

Install shell in ground

Install equipment pack

Connect plumbing

Connect electrical

components

Pour the deck

Planning the Best Location

Safety rst

Do not place your spa within 10 feet (3 m) of overhead power lines.

Make sure the spa is positioned so that access to the equipment

compartment and all side panels will not be blocked. Be certain that your

installation will meet all city and local safety codes and requirements.

Consider how you will use your spa

How you intend to use your spa will help you determine where you should

position it. For example, will you use your spa for recreational or therapeutic

purposes? If your spa is mainly used for family recreation, be sure to leave

plenty of room around it for activity. If you will use it for relaxation and

therapy, you’ll probably want to create a specic mood around it.

Plan for your environment

If you live in a region where it snows in the winter or rains frequently, place

the spa near a house entry. By doing this, you will have a place to change

clothes and not be uncomfortable.

Consider your privacy

In a cold-weather climate, bare trees won’t provide much privacy. Think of

your spa’s surroundings during all seasons to determine your best privacy

options. Consider the view of your neighbors as well when you plan the

location of your spa.

Provide a view with your spa

Think about the direction you will be facing when sitting in your spa. Do

you have a special landscaped area in your yard that you nd enjoyable?

Perhaps there is an area that catches a soothing breeze during the day or

a lovely sunset in the evening.

Keep your spa clean

Prevent dirt and contaminants from being tracked into your spa by placing

a foot mat at the spa’s entrance where the bather’s can clean their feet

before entering your spa. You may also consider keeping a small water-

lled basin nearby for bathers to rinse their feet before entering your spa.

In planning your spa’s location, consider a location where the path to and

from the house can be kept clean and free of debris.

Allow for service access

Many people choose to install a decorative structure around their spa. If

you are installing your spa with any type of structure on the outside, such

as a gazebo, remember to allow access for service. It is always best to

design special installations so that the spa can still be accessed.

Consider the best place for the outdoor equipment pack

(in-ground spas only)

The Designer Spa series requires an external equipment pack. When

locating the outdoor equipment pack, you will want to consider the

following:

The equipment pack must be located within a maximum of 15 feet•

from the spa.

Ensure the equipment running its normal ltration cycles does not •

make too much noise for spa owners and/or neighbors.

Ensure the equipment can be easily serviced for lter cleaning and •

periodic inspections in the location chosen.

If you are using a gas heater, you will need to consider wind and drafts•

as well as heater exhaust for proper heater placement. (See heater

owner’s manual for important location and safety information.)

The equipment base and heater must be placed on either a 3 1/2”•

cement slab or 3” paving stones.

Make sure the equipment area selected will not be in an area where•

water could run or stand.

If the area receives direct sunlight, you will want to provide some•

protection for the equipment portion of the equipment pack.

The equipment pack and heater are delivered separately. Do not cover gas

heaters unless properly vented. (See heater owner’s manual for important

safety information.)

Portable Spa Site Preparation

Your spa needs a solid and level foundation. The area that it sits on must

be able to support the weight of the spa, with water and the occupants who

use it. If the foundation is inadequate, it may shift or settle after the spa

is in place, causing stress that could DAMAGE YOUR SPA SHELL AND

FINISH.

Note: Damage caused by inadequate or improper foundation support is

not covered by the warranty. It is the responsibility of the spa owner to

provide a proper foundation for the spa.

Place the spa on an elevated foundation (preferably a 3” - 4” concrete

slab). Pavers, gravel, brick, sand, timbers or dirt foundations are not

adequate to support the spa. If you are installing the spa indoors, pay

close attention to the ooring beneath it. Choose ooring that will not be

damaged or stained.

If you are installing your spa on an elevated wood deck or other structure, it

is highly recommended that you consult a structural engineer or contractor

to ensure the structure will support the weight of 150 pounds per square

foot.

To properly identify the weight of your new spa when full, remember water

weighs 8.33 lbs. per gallon. For example, an average 8’ spa spa holds

approximately 500 gallons of water. Using this formula, you will nd that

the weight of the water alone is 4,165 lbs. Combined with the dry weight

of the spa you will note that this spa will weigh approximately 5,000 lbs.

when full of water.

Note: It is strongly recommended that a qualied, licensed contractor

prepare the foundation for your spa.

Your Cal Spas®retailer can help you with your foundation and more. Your

retailer has a wealth of information and experience about how to get the

most out of your spa and can provide you with a full line of accessories

that are designed to complement your spa and increase your enjoyment.

In-Ground Spa Site Preparation

Ensure there is enough room for the spa and equipment.•

The equipment pack must be located within a maximum of 15 feet•

from the spa.

Plan for proper electrical and gas service to both the equipment area•

and spa side.

Ensure the required at, level foundation can be constructed in the •

area chosen.

The spa must be properly back-lled with wet sand, underneath and •

on all four sides.

The nal architecture must include permanent ground coverage within •

a 10 feet radius of the spa.

Never place any spa in a sealed area. Water must be able either to be•

absorbed into the surrounding area or channeled away. Water build-

up under and/or around the spa, will cause the spa to oat out of the

ground.

Grading Prior to Excavation

Selection of the Designer Spas site will determine how much grading will

have to be accomplished prior to the actual dig for the spa. Naturally, a

level area is best because it will require the least amount of preparation for

the dig, but in many cases there is no level area, therefore, the site must

be prepared to accept the Spa prior to dig. The spa site should be elevated

slightly higher than the surrounding area

When dealing with slopes, the severity of the slope will determine if

retaining walls must be built in order to have a level area for the spa. If the

slope is relatively minor, contact your local building safety.

Site Excavation – Hard Bottom

For hard bottom placement for in-ground spas, you will need a smooth and

at concrete surface at least 4” thick as large as the bottom contact points.

Be sure not to seal the bottom off and making a sealed box. You will need

adequate water drainage for escape under the spa. A gravel beds around

the concrete base will help with this.

Site Excavation – Sand Bottom

With the spa area and all elevations planned including your decided type

of decking, you are now ready to proceed with the dig. An ideal excavation

is one that is as close as possible to the dimensions of the spa shell, but

with the following rules in mind. The excavation should be 2” to 4” deeper

than the actual spa for your sand bed. The sand bed is to level the spa

shell and provide a perfect support base with no voids when the spa is

lowered into the hole. Your excavation should be approximately one foot

longer and one foot wider than the spa shell. This will allow for a six inch

over dig all the way around the spa once it is in place. Additional hand

excavation will be required to insure the skimmer will t in the excavation

when attached to the spa.

Sand or rock dust must be used to bed the shell into the excavation and

for backll. In no event is dirt to be used. One of the easiest ways to know

how much sand is needed to be placed on the bottom of the excavation is

to set a grade stake at all four corners, and one on each side of the center

line in the bottom of the hole. If there are areas that are deeper than 2” to

4”, these can be lled with sand and are of no consequence.

Getting the Spa Into Your Yard

Check the Dimensions of Your New Cal Spa®

The Cal Spas® specication chart lists your spa’s model and its dimension

as it sits on the delivery cart. During delivery, the spa must remain on the

delivery cart at all times. Compare the dimensions to the width of the gates,

sidewalks, and doorways along the delivery route. It may be necessary for

you to remove a gate or partially remove a fence in order to provide an

unobstructed passageway to the installation location.

Plan the Delivery Route

Consider the following when planning your delivery route:

Check the width of gates, doors and sidewalks to make sure your spa•

will pass through unobstructed. You may have to remove a gate or

part of a fence to allow for adequate width clearance.

Are there low roof eaves, overhanging branches or rain gutters that•

could be an obstruction to overhead clearance?

8’ spas need at least 42” wide gate and 9’ height clearance.•

If the delivery route will require a 90º turn, check the measurements at•

the turn to ensure the spa will t.

Are there protruding gas meters, water meters or A/C units on your•

home which will cause obstructions along the delivery path to your

yard?

Are there stairs in your delivery route? If so, you must consult your Cal•

Spas®dealer prior to delivery to make adequate preparations.

Special Circumstances

The use of a crane for delivery and installation may become necessary if

you are unable to provide an adequate delivery route. It is used primarily

to avoid injury to your spa, your property or to delivery personnel. Your Cal

Spas®dealer may be able to assist you with the arrangements. If your spa

delivery requires the use of a crane, the cost of a crane is generally not

included in the standard delivery service.

Electrical Requirements

Electrical Requirements – US and Canada

240 Volt Electrical Installation

All 240V spas must be permanently connected (hardwired) to the power

supply. These instructions describe the only acceptable electrical wiring

procedure. Spas wired in any other way will void your warranty and may

result in serious injury.

This is the only acceptable electrical wiring procedure. Spas wired in any

other way will void your warranty. See the wiring diagram on page 9.

When installed in the United States, the electrical wiring of this spa must

meet the requirements of National Electric Code, ANSI/NFPA 70-2008 and

any applicable local, state, and federal codes. The electrical circuit must

be installed by an electrical contractor and approved by a local building /

electrical inspector.

GFCI and Wiring Requirements

The power supplied to the spa must be on a dedicated GFCI protected

circuit as required by ANSI/NFPA 70 with no other appliances or lights

sharing the power.

Use copper wire with THHN insulation. Do not use aluminum wire.

Use the table on the next page to determine your GFCI and wiring

requirements.

When NEC requires the use of wires larger than #6 AWG, install a junction

box near the spa and use #6 AWG wire between the junction box and the

spa.

Wire runs over 85 feet must increase wire gauge to the next lower number.

For example: A normal 50 amp GFCI

with four #8 AWG Copper wires run

over 85 feet would require you to go to

four #6 AWG copper wires.

Read and follow the heater

manufacturer’s safety and installation

instructions prior to installation and

operation. Incorrect installation may

damage the heater and void its

warranty.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Jacuzzi de Calspas

Calspas

Calspas LTR20051000 Manual de usuario

Calspas

Calspas LTR20111058 Manual de usuario

Calspas

Calspas Spa Surrounds Manual de usuario

Calspas

Calspas Home Resorts FA-1325 Manual de usuario

Calspas

Calspas Portable Spas Manual de usuario

Calspas

Calspas THE CHILL SPA Manual de usuario

Calspas

Calspas LTR20121002 Manual de usuario

Calspas

Calspas Gazebos Manual de usuario

Calspas

Calspas Ultimate Fitness Hot Tub Manual de usuario

Calspas

Calspas SWIM PRO SPAS Manual de usuario

Calspas

Calspas Avalon A526 Manual de usuario

Calspas

Calspas LTR20101000 Manual de usuario

Calspas

Calspas Spa Wrap Manual de usuario

Calspas

Calspas Cal Spas Home Resort Manual de usuario

Calspas

Calspas Platinum Series Manual de usuario

Calspas

Calspas patio plus Manual de usuario

Calspas

Calspas 6115 Manual de usuario

Calspas

Calspas Inground Series Manual de usuario

Calspas

Calspas PATIO Manual de usuario

Calspas

Calspas Patio Series Manual de usuario

Calspas

Calspas Inground Spas Manual de usuario

Calspas

Calspas F 1239 Manual de usuario

Calspas

Calspas Pneumatic Series Manual de usuario

Calspas

Calspas SWIM Manual de usuario

Manuales populares de Jacuzzi de otras marcas

Bestway

Bestway Lay-Z-Spa 54189 Manual de usuario

Jacuzzi

Jacuzzi ARGA ARG101C0110 Manual de lista de piezas

Morphy Richards

Morphy Richards Essentials PC4006 Manual de usuario

Softub

Softub PRESTIGE Manual de usuario

JNJ SPAS

JNJ SPAS SPA-318 Manual de instalación

KIRAMI

KIRAMI Comfort Family Manual de usuario

QCA Spa

QCA Spa VS501 PAK (VL260 TOPSIDE) Manual de usuario

HoMedics

HoMedics FB-655HJ-GB Manual de usuario

Everyday Hot Tubs

Everyday Hot Tubs 530 Manual de usuario

anko

anko SS-601A Manual de usuario

Jacuzzi

Jacuzzi Duetta 6042 Manual de usuario

Pooli

Pooli OS030979B Manual de usuario

Jacuzzi

Jacuzzi alimia Manual de usuario

ab Solares Smart Spa Manual de usuario

CalderaSpas

CalderaSpas CalderaSpas Utopia Series Manual de usuario

Outsunny

Outsunny 848-047V70 Manual de usuario

Aquatic

Aquatic INFINITY 1 Manual de usuario

Master Spas

Master Spas MP Force Manual de usuario