call4tel NX-S/O 2 Series Manual de instrucciones
call4tel
NX-S/O 2/4/8
Analog Gateway
Quick User Guide
INDEX
OVERVIEW
NX-S/O 2/4/8 PORTS
CONNECTING THE IAG800 V2
CONFIGURING THE NX-S/O 2/4/8
Obtaining the IP address
Configure by Web GUI
Via LAN1 Port
Via LAN2 Port
Configure by the IVR
2
3
4
4
4
4
4
5
5
2
OVERVIEW
NX-S/O 2/4/8 Series Analog Gateway, is an open-source Asterisk-based Analog VoIP Gateway solution for
SMBs and SOHOs. With a friendly GUI and unique modular design, users can easily set up their customized
Gateway. Also, secondary development can be completed through AMI (Asterisk Management Interface).
PACKAGE CONTENTS
1 X FOOT PAD1 X DEVICE
1 X 1M LAN CABLE 1 X 12V/2A POWER ADAPTER 1 X CERTIFICATE
3
NX-S/O 2/4/8 PORTS
1: Power Indicator
2: System LED
3: Analog Telephone Interfaces and corresponding Channels State Indicators
1: Power interface
2: Reset button
3: Ethernet ports and indicators
4
CONNECTING THE IAG800 V2
The NX-S/O 2/4/8 is designed for easy configuration and easy installation. To connect the NX-S/O 2/4/8,
please follow the steps above:
1. Plug a standard RJ11 telephone cable into the phone port and connect the other end of the telephone
cable to a standard touch-tone analog telephone.
2. Plug the Ethernet cable into the LAN port of the NX-S/O 2/4/8 and connect the other end of the Eth-
ernet cable to an uplink port (a router or a modem, etc.)
3. Plug the power adapter into the NX-S/O 2/4/8 and connect it to a wall outlet.
4. When the phone adapter is ready for use, the Power, Ethernet, and phone LEDs will be solidly lit.
CONFIGURING THE NX-S/O 2/4/8
The NX-S/O 2/4/8 can be configured either through the PC’s Web browser using the embedded Web GUI or
using the IVR voice prompt menu.
OBTAINING THE IP ADDRESS
The NX-S/O 2/4/8 is configured with DHCP by default. To know the IP address of the NX-S/O 2/4/8, you can
refer to the following steps to obtain an IP address.
1. Using an analog phone, connect to any of the phone ports.
2. Press ** (press the star key 2 times) will announce the current IP address. The default is to broadcast
the IP in English.
CONFIGURE BY WEB GUI
Via LAN1 Port
If your NX-S/O 2/4/8 is connected through LAN1 port, please refer to the following steps.
1. Power your NX-S/O 2/4/8 with the correct size AC/DC.
2. Open a web browser on your computer.
3. Enter the IP address of the NX-S/O 2/4/8 into the address bar of your browser.
4. Enter the administrator password to access the Web Configuration Menu. (By default, the adminis-
trator user name and password are admin).
5
Note: The computer must be connected to the same subnet as the NX-S/O 2/4/8. This can easily be done by
connecting the computer to the same hub or switch as the NX-S/O 2/4/8.
Via LAN2 Port
If your NX-S/O 2/4/8 is connected via the LAN2 port, please refer to the following steps.
1. Power up your NX-S/O 2/4/8 with the correct size AC/DC.
2. Open a web browser on your computer.
3. Enter the default LAN2 IP address (172.16.99.1) into the browser address bar.
4. Enter the administrator password to access the Web Configuration Menu. (By default, the adminis-
trator user name and password are admin).
Note: Please make sure your computer has a valid IP address in the range of 172.16.99.XXX so that you can
access the Web GUI of NX-S/O 2/4/8.
Configure by the IVR
1. Using an analog phone, connect to any of the phone ports.
2. Pick up the handset and dial “*3*” to configure the IP address using IVR.
3. Follow the prompts to set DHCP or Static IP, here is an example of Static IP setting.
• Pick up the handset and dial “*3*” to configure the IP address using IVR.
• Press 2 to set the static IP (192.168.1.11).
• Set IP: Press 192168001011, three digits do not need to fill in the full number 0, vacant need
to fill in the 0.
• Set subnet: 25525525255000.
• Set the gateway: can be omitted, press 0.
• After setting correctly, wait for the device to start normally, use the analog phone, pick up the handset
and dial “**” to check whether the modified IP address works.
Note: This IP address setting is only valid for NX-S/O 2/4/8 LAN2, and for LAN1, you need to go to Web GUI to
set the IP address.
Otros manuales para NX-S/O 2 Series
1
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Puerta de call4tel
Manuales populares de Puerta de otras marcas
LST
LST M500RFE-AS Manual de usuario
Kinnex
Kinnex Media Gateway Manual de usuario
2N Telekomunikace
2N Telekomunikace 2N StarGate Manual de usuario
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario
Telsey
Telsey CPVA 500 - SIP Manual de usuario
