California Air Tools 365CR Manual de usuario

WARNING

Even when the tool is used as prescribed, it is not possible to eliminate all risk factors.

The following hazards may occur when using this tool.

�Damage to lungs if a dust mask is not worn.

�Damage to hearing if hearing protection is not worn.

�Wear eye protection.

California Air Tools 365CR (5) Gallon Pressure Pot

IMPORTANT:

Read all safety and operating

instructions carefully before use.

Keep this Manual for reference.

Description:

The sturdy construction and compact design makes this product the ideal choice for both amateur

and professional.

Designed for resin casting.

An air compressor, air hose are needed to operate this tool.

Item No.

365CR

Max Pressure:

80 PSI

Capacity:

5 Gallon

Air Input:

1/4”

Exterior:

16"W & 24 1/2" H

Inner:

13"W & 14 3/4" D

Safety Guidelines:

This manual contains information that is important for you to know and understand.

This information is for your protection and safety. Improper use, operation or maintenance of this product could

result in injury or property damage.

Please Read and understand all warnings and operating instructions before use. Save these instructions.

arning

Over pressuriza

on can result in explosion. Max: 80 PSI Operating PSI: 60 PSI

1. Exceeding the Maximum pressure in the tank can cause the tank to over pressurize and explode resulting in

serious injury or property damage. Always make sure that equipment connected to tank or hose outlet has a

higher pressure rating than the regulated air pressure in the tank.

arning

Risk of tank explosion.

1. Modiﬁcations to the tank’s design or construction could weaken it. Assemble tank components

in accordance with the service instructions. Do not drill into tank, or weld attachments, or alter

its design in any manner.

2. Substitution of unauthorized non-standard components could weaken tank or cause

component failure. Use only those components furnished with the tank. Assembled in

accordance with instructions in the service literature.

3. Damage to the tank or its components could weaken the tank. Never attempt to repair a

damaged tank. Replace it with a new one.

4. Improper cleaning or maintenance could block air passages to the safety valve, gauge or outlet,

allowing pressure to rise to dangerous levels, and preventing the lowering of tank pressure.

Following each use, clean and dry tank and lid in accordance with maintenance instructions.

Ensure ports to safety valve, gauge and outlet are free of materials which could

prevent free movement of air.

5. Tampering with the safety valve could allow tank pressure to rise to dangerous levels. Never

attempt to adjust safety valve to change its pressure setting or defeat its function in any way.

Operate the valve before each use to assure that it functions properly.

6. Removal of the lid while the tank is under pressure could result in the lid being propelled

violently from the tank. Before releasing clamp force to remove the lid, shut oﬀ the supply of

tank inlet air and turn the regulator knob counterclockwise to relieve air pressure. Check by

pulling the safety valve ring.

7. Use of reactive chemicals could attack the lid gasket and safety valve seal, allowing tank

pressure to rise to dangerous levels.

If this reaction occurs within an enclosed structure such as this tank, it may cause explosion. Do not use

reactive chemicals in your tank such as acids, caustic solutions, or halogenated hydrocarbon solvents.

8. Over tightening clamps, causing them to weaken and fail could result in the lid being propelled

violently from the tank. If the lid gasket leaks, relieve the tank pressure and clean or replace

the gasket.

Assembly

1. Attach the swivel wheels (4) to the base legs on thetank.

2. Attach the air hose to the inlet fitting located on the tank regulator.

Using an air pressure regulator on a pressure pot for resin casting regulates the amount of pressure applied to the resin

castings inside the tank.

Important: Before introducing air pressure into the tank, ensure the lids gasket is properly installed

and clean of debris that may interfere with sealing properly to the rim of the pot. Unlock pressure

regulator knob and rotate counterclockwise until is stops.

Ope

tio

1. Before ﬁlling the tank with material, ensure ports to safety valve, gauge and outlet are free of

materials which could prevent free movement of air. Lid gasket must be properly installed and

seated in the lid and be clean of any debris that may prevent a proper seal. Rim of the pot must

also be clean and free of debris.

2. Place castings/molds into pot.

3. Place lid assembly on tank and hand tighten tank lid clamp screws.

4. Close ball valve, unlock pressure regulator knob and rotate counterclockwise until it stops.

5. Attach air hose, open ball valve and begin slowly introducing pressure into the tank by rotating

the pressure regulator knob clockwise until the desired pressure has been achieved. Consult

resin manufacturer’s instructions for the proper PSI setting. NOTE: Introducing pressure too

quickly will result in pushing resin out of the mold(s) and onto the interior surfaces of the pot.

6. Normal operating pressure on the tank is 60 PSI. Should you need to reduce pressure,

simply rotate the pressure regulator knob counterclockwise until the desired pressure

setting is achieved. When the proper pressure setting has been obtained lock the pressure

regulator knob into place by pressing in, turn ball valve to the closed position and remove

air hose.

7. Once the resin has cured per resin manufacturers specifications slowly relieve the

pressure by slowly rotating the Air Outlet Cock counterclockwise until the pressure bleeds

down completely.

8. Once tank is completely bleed loosen tank lid clamp screws and remove lid.

arning

Do not use over 80 PSI in your tank.

Clean

arning

Always shut oﬀ air pressure at the source and bleed oﬀ all pressure in the

tank by slowly rotating the Air Outlet Cock counterclockwise, relieving the air pressure.

It is very important that the tanks interior and lid be cleaned as soon as the job is ﬁnished.

Turn oﬀ the main air supply to the tank. Remove all pressure by slowly rotating the Air Outlet

Cock counterclockwise until the pressure bleeds completely down.

Warranty

Limited Warranty: 1 Year

This warranty is limited to California Air Tools Products.

California Air Tools will repair or replace, free of charge, to the original retail customer whom purchased a

California Air Tools product from an authorized dealer.

This warranty does not transfer subsequent owners.

California Air Tools will repair or replace, at its option, any parts that are proven by an authorized service center

to be defective in material or workmanship under normal use during the application warranty time period stated

as above.

The limited warranty covers the cost of the replacement parts and labor for defects when installed by

an authorized service center.

Transportation charges are the responsibility of the customer.

The limited warranty period begins on the date of the retail purchase by the orginal purchaser.

California Air Tools

8560 Siempre Viva Road

San Diego, Ca 92154

866-409-4581

www.californiaairtools.com

NO.

Part

NO.

Part

Butterfly Nut

Connector

Washer

Filter Circlip

Sealing Washer

Ball Valve

Combination Tank Cover

Connector

Lock Bolt

Elbow

Universal Quick Coupler

Split Washer D: 8.5

Air outlet Cock

Combination Tank

Safety Valve

Nut M8

Spring Washer

Wheel

N/A

Pressure Gauge

Sealing Washer

Cap

Air Converter

Air Inlet Plug

Nut

Fluid Inlet Plug

Nut

Tabla de contenidos

Otros manuales de Compresor de aire de California Air Tools

California Air Tools

California Air Tools 10020SPC Manual de usuario

California Air Tools

California Air Tools 5510SE-22050 Manual de usuario

California Air Tools

California Air Tools 8010AD Manual de usuario

California Air Tools

California Air Tools 1610A Manual de usuario

California Air Tools

California Air Tools 12V1P10S Manual de usuario

California Air Tools

California Air Tools 15033CR Manual de usuario

California Air Tools

California Air Tools SP-9413 Manual de usuario

California Air Tools

California Air Tools 20020AD Manual de usuario

California Air Tools

California Air Tools 10020CAD Manual de usuario

California Air Tools

California Air Tools 20020 Manual de usuario

California Air Tools

California Air Tools 10020HDCADC Manual de usuario

California Air Tools

California Air Tools 8010SPC Manual de usuario

California Air Tools

California Air Tools 8010DSPC Manual de usuario

California Air Tools

California Air Tools 8010DSPCAD Manual de usuario

California Air Tools

California Air Tools 8010SPCAD Manual de usuario

California Air Tools

California Air Tools 4710SQ Manual de usuario

California Air Tools

California Air Tools 8010AAD Manual de usuario

California Air Tools

California Air Tools 2010A Manual de usuario

California Air Tools

California Air Tools 210DLV Manual de usuario

California Air Tools

California Air Tools 20020-22060 Manual de usuario

California Air Tools

California Air Tools CAT-10020DSPCAD Manual de usuario

California Air Tools

California Air Tools 20060CAD Manual de usuario

California Air Tools

California Air Tools 1P1060SP Manual de usuario

California Air Tools

California Air Tools 1P1060S Manual de usuario

Manuales populares de Compresor de aire de otras marcas

Sparmax

Sparmax DC-25XR Manual de usuario

KAESER

KAESER M122 Manual de usuario

GMC

GMC GAC1500 Manual de usuario

Briggs & Stratton

Briggs & Stratton Air Compressor Manual de usuario

Fini

Fini F3GST2TK Manual de usuario

Industrial Air

Industrial Air CP1580325 Manual de programación

Campbell Hausfeld

Campbell Hausfeld RP3300 Guía de inicio rápido

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Manual de usuario

Hitachi

Hitachi EC99S Manual del operador

Parkside

Parkside PKO 270 A1 Manual de usuario

Sullair

Sullair 185 Manual de usuario

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Manual de usuario

Ferm

Ferm CRM1046 Manual de usuario

BE AC153 Manual de usuario

RIDGID

RIDGID OF25150A Manual de usuario

Johnson Controls

Johnson Controls QUANTUM LX Manual

Sears

Sears Craftsman 919.167463 Manual de usuario

Ring Automotive

Ring Automotive RAC700 Manual de usuario