Calculated Industries HeavyCalc Manual de usuario
For Today’s Excavation Professional
CONSTRUCTION MASTER
HEAVYCALC™
USER’SGUIDE
Introducing HeavyCalc . . . . . . . . . . . . . . . . . .3
Key Definitions . . . . . . . . . . . . . . . . . . . . . . 4
Basic Functions . . . . . . . . . . . . .4
Dimension Keys . . . . . . . . . . . . .6
Area/Volume & Angle Keys . . . . .9
Excavation/Volume Keys . . . . . .10
Additional Key Functions . . . . .12
Fractional Rounding Settings . . .13
Using the HeavyCalc . . . . . . . . . . . . . . . . . .14
Linear Dimensions . . . . . . . . . .14
Square and Cubic Dimensions . .15
Dimension Conversions . . . . . .16
Math Operations . . . . . . . . . . .19
Memory Operation . . . . . . . . . .22
Fraction Settings . . . . . . . . . . . .25
Paperless Tape Function . . . . . .27
Linear Calculations . . . . . . . . . .29
Area Calculations . . . . . . . . . . .31
Volume Calculations . . . . . . . . .32
Right Triangle Problems . . . . . .37
Basic Cut/Fill Solutions . . . . . . .42
Shrink & Swell Solutions – . . . . . .
Material Volume . . . . . . . . . .46
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . .50
Accuracy/Display . . . . . . . . . . .50
“Error” . . . . . . . . . . . . . . . . . . .50
Auto-Range . . . . . . . . . . . . . . .50
Battery and Auto Shut–off . . . .51
Full Reset/All–Clear . . . . . . . . .51
Warranty . . . . . . . . . . . . . . . . .52
TABLE OF CONTENTS
2 – HeavyCalc™
Designed for today’s excavation and
heavy construction professional, the
Construction Master HeavyCalc™ adds
even more power to the Construction
Master line-up. As with earlier models,
this calculator is so simple to use, even
the novice will find it easy to solve
hundreds of dimension-related prob-
lems right in feet, inches, fractions and
cubic yards!
◆Solve Dimensional Math with Ease
◆Instant Dimensional Conversions
◆English/Metric Conversions
◆Weight/Volume Conversions
◆Calculate Square & Rectangular Areas
◆Determine Cubic Volumes
◆Determine % Grade and Slope
◆Determine Cut and Fill
◆Find Bank, Loose & Compact Volumes
◆Instant Square-Up (Diagonal) Solutions
◆Constant Add feature
◆Average Calculations
◆Material Estimations
◆Paperless Tape Register
INTRODUCING HEAVYCALC™
User’s Guide – 3
Basic Functions
[+] [–] [x] [÷] [=]
Math Operators —Used to calculate
math problems.
[%]
Percent — Four-function percent key.
0 – 9 and [ • ]
Numerical Digits and Decimal Point
Used for keying in numbers.
[Off]
Power Off— Turns all power off.
Resets the display and all non-perma-
nent registers.
[On/C]
On/Clear — Turns on power. One
press clears the last entry and display.
Two presses clear all temporary registers.
[Conv]
Convert —Used with dimensional
keys to convert among dimensions.
Dimensions can only be converted with-
in the same convention (i.e., linear,
square or cubic). Also used to access
special functions when used in combi-
nation with other keys.
KEY DEFINITIONS
4 – HeavyCalc™
[Cnst]
Constant – This key is used to store a
value permanently for use as a con-
stant in repeated calculations.
[Conv] [Cnst]
Square Root —Used to find the square
root of a non-dimensional or area
value.
[M+]
Memory Add —Adds the displayed
value to the Memory total in the sum-
mation register. The Memory total is
recalled by pressing [Rcl] [M+].
[Conv] [M+]
Memory Subtract —Subtracts the dis-
played value from Memory.
[Rcl]
Recall —Recalls values stored in any
register (i.e., press [Rcl] and then the
key you wish to display the value of).
[Rcl] [Rcl]
Memory Recall and Clear — Displays
and clears the value in memory.
[Conv] [Rcl]
Memory Clear — Clears Memory with-
out changing the display.
User’s Guide – 5
Dimension Keys
[Yds]
Yards —This is an entry and conver-
sion key (when used with [Conv]).
The entry can be a whole number or a
decimal number.
[Feet]
This is an entry and conversion key
(when used with [Conv]). The entry
can be in whole or decimal numbers.
This key can also be used in conjunc-
tion with the [Inch] and [/] keys for
entering values in Feet-Inch format.
For example, 6 feet 9-1/2 inches is
entered as follows: 6 [Feet] 9 [Inch] 1
[/] 2. Repeated presses of this key
during conversions will toggle
between Feet-Inch and Decimal Feet
formats.
[Inch]
This is an entry and conversion key.
The entry can be in whole or decimal
numbers. This key can also be used
with the [/] key for entering values in
Fractional Inch format. For example,
enter 9-1/2 inches as: 9 [Inch] 1 [/] 2.
Repeated presses of [Inch] during con-
versions, toggles between Fractional
Inch and Decimal Inch formats.
6 – HeavyCalc™
[ / ]
Fraction Bar —This key is used to
enter fractions. Fractions can be
entered as proper (1 or less – 1/2, 1/8,
1/16) or improper (greater than 1 –
3/2, 65/64). For example, to enter 1/2,
the key sequence would be: 1[/] 2.
If the denominator (the bottom num-
ber) is not entered, then the set frac-
tional level (1/16, 1/2, etc.) is used.
[Rcl] [/] displays the current fractional
setting.
[Rcl] [x]
Imperial/Metric Mode —Selects
either Imperial or Metric defaults for
the following settings: pitch, stair riser
height, and on-center spacing.
[Cu]
Cubic —This key is used with a
dimension key (feet, inches, yards,
meters, or millimeters) to identify a
volume value. Example: 5 [Cu] [Yds].
[Sq]
Square —This key is used with a
dimension key (feet, inches, yards,
meters, or millimeters) to identify an
area value. Example: 10 [Sq] [Feet].
User’s Guide – 7
[m]
Meters —This is an entry and conver-
sion key used to enter decimal meters
or, when used with [Conv], to convert
to decimal meters from some other
dimensional format.
[mm]
Millimeters —This is an entry and
conversion key used to enter decimal
millimeters or, when used with [Conv],
to convert to decimal millimeters from
another dimensional format.
[Weight]
This key is used to convert a dimen-
sioned cubic value or volume to a
weight value using the [Conv] key and
the stored Weight per Volume (see
below). For example, 5 [Cu] [Yds]
[Conv] [Weight] equals 7.5 tons, or 10
[Weight] (tons) [Conv] [Cu] [Yds]
equals 6.666667 cubic yards. Repeated
presses of this key, after a cubic entry
or conversion, toggles among tons,
pounds and kilograms.
[Conv] [%]
Weight per Volume —Used to set the
Weight per Volume. Can be pro-
grammed as Tons per Cubic Yard,
Pounds per Cubic Yard, or Kilograms
per Cubic Meter. Default is 1.5 Tons
per Cubic Yard. To set a different
weight per volume, for example, 2
8 – HeavyCalc™
Tons per Cubic Yard, press 2 [Conv]
[%]. Value will be permanently stored.
To recall stored value, press [Rcl] [%].
Area/Volume & Angle Keys
[Length]
Enters the value for length in dimen-
sion problems (e.g., for calculating
area or volume).
[Conv] [Length]
Square-up —Computes the diagonal,
or “square-up,” based on entered
length and width.
[Width]
Enters the value for width in dimen-
sion problems (e.g., for calculating
area or volume). Also computes width
from entered values of depth and per-
cent grade or slope.
[Conv] [Width]
Percent Grade —Used to enter and
display percent grade. Also computes
percent grade using entered values for
width and depth, or slope.
[Depth]
Enters the value for depth in dimen-
sion problems (e.g., for calculating
volume). Also computes depth from
entered values of width and percent
grade or slope.
User’s Guide – 9
[Conv] [Depth]
Slope — Used to enter slope as a ratio
of run per unit rise (e.g., 4:1), or in
decimal degrees (e.g., 10°). Also com-
putes slope using entered value for
width and depth, or percent grade.
Note: Only works with width. Does not
operate in conjunction with length.
[Vol]
Volume —Computes the volume (in
cubic yards) based on entered length,
width and depth values. A second
press will display the area (in square
feet) based on entered length and
width. Successive presses will toggle
the display between the calculated
area and volume.
[Conv] [Vol]
Area – Computes the area (in square
feet) based on entered length and
width.
Excavation/Volume Keys
[Cut/Fill]
Used to enter or calculate the cut or fill
amount (based on entries of proposed
and existing benchmarks). A fill is dis-
played as a positive value; a cut as a neg-
ative value.
10 – HeavyCalc™
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Calculadora de Calculated Industries
Calculated Industries
Calculated Industries 8515 Manual de usuario
Calculated Industries
Calculated Industries SCALE MASTER CLASSIC 6020 Manual de usuario
Calculated Industries
Calculated Industries Hot Rod Calc 8703 Manual de usuario
Calculated Industries
Calculated Industries 3416 Manual de usuario
Calculated Industries
Calculated Industries Construction Master 5 4050 Manual de usuario
Calculated Industries
Calculated Industries 4088 Manual de usuario
Calculated Industries
Calculated Industries 4225 Manual de usuario
Calculated Industries
Calculated Industries 6260 Manual de usuario
Calculated Industries
Calculated Industries ConstructionMaster HeavyCalc 4320 Manual de usuario
Calculated Industries
Calculated Industries Construction Master III Manual de usuario
Calculated Industries
Calculated Industries Construction Master plus EZ 4067 Manual de usuario
Calculated Industries
Calculated Industries Sheet Metal/HVAC Pro Calc Manual de usuario
Calculated Industries
Calculated Industries PlumbingCalc Pro Manual de usuario
Calculated Industries
Calculated Industries 3423 Manual de usuario
Calculated Industries
Calculated Industries 8305 KitchenCalc Pro Manual de usuario
Calculated Industries
Calculated Industries Construction Master IV Manual de usuario
Calculated Industries
Calculated Industries 3265 Manual de usuario
Calculated Industries
Calculated Industries TimeCard Tabulator II Manual de usuario
Calculated Industries
Calculated Industries 3420 Manual de usuario
Calculated Industries
Calculated Industries ElectriCalc Pro Manual de usuario
Calculated Industries
Calculated Industries KitchenCalc 8300 Manual de usuario
Calculated Industries
Calculated Industries Construction Master IV Manual de usuario
Calculated Industries
Calculated Industries Pocket Handyman IV Manual de usuario
Calculated Industries
Calculated Industries 9130 Manual de usuario
