Cadet FP052TB Manual de usuario

cadetheat.com

855.CADET.US

Vancouver, Washington

USA

http://cadetheat.com/install/fp

For how-to videos or more information, please visit:

OWNER’S GUIDE

Thank you for your purchase! Question or problem? Let us solve it

with a single phone call, email or online chat! We’ll save you a trip

back to the store!

Phone: 855.CADET.US (855.223.3887)

email: [email protected]

Live chat: cadetheat.com (contact us)

Cadet Customer Service

FROST

PROTECTION

HEATER

SAVE THESE INSTRUCTIONS

IMPORTANT INSTRUCTIONS

1. Read all instructions before

installing or using this heater.

2. This heater is hot when in use.

To avoid burns, do not let bare

skin touch hot surfaces. Keep

combustible materials, such

as furniture, pillows, bedding,

papers, clothes, etc. and curtains

at least 3 feet (0.9 meters) from

the front of the heater and keep

them away from the sides.

3. Extreme caution is necessary

when any heater is used by or

near children or invalids and

whenever the heater is left

operating and unattended.

4. Do not operate any heater after

it malfunctions. Disconnect

power at service panel and have

heater inspected by a reputable

electrician before reusing.

5. Do not use outdoors.

6. To disconnect heater, turn

control(s) to o󰀨, and turn o󰀨

power to heater circuit at main

disconnect panel.

7. Do not insert or allow foreign

objects to enter any ventilation

or exhaust opening as this may

cause an electric shock or ﬁre, or

damage the heater.

8. To prevent a possible ﬁre, do not

block air intakes or exhaust in

any manner.

9. A heater has hot and arcing or

sparking parts inside. Do not use

it in areas where gasoline, paint,

or ﬂammable vapors or liquids

are used or stored.

10. Use this heater only as

described in this manual. Any

other use not recommended by

the manufacturer may cause

ﬁre, electric shock, or injury to

persons.

11. WARNING: Connecting a heater

to a voltage higher than what’s

listed on its rating label will

destroy the heater and could

start a ﬁre.

12. A heater will not heat properly

when connected to a voltage

lower than what’s listed on its

rating label.

When using electrical appliances, basic precautions should always be

followed to reduce the risk of ﬁre, electric shock, and injury to persons,

including the following:

KNOW YOUR VOLTAGE!

120 volt

single-pole breaker

240 volt

double-pole breaker

If you are uncomfortable working with electricity, running electrical supply wire or

installing a circuit breaker, please consult a licensed electrician. Make sure power

to the heater is turned o󰀨 at the main disconnect panel whenever doing any work

on a heater. Serious injury or electrocution can result from electric shock.

• CHECK YOUR BREAKER! If you’re replacing an existing heater, check the

labels of the old heater and use the same voltage.

Unanswered questions? Call our technical support team in Vancouver,

Washington toll free at 855.223.3887 or outside the USA 360.693.2505

TOOLS REQUIRED

Tape Measure

Straight and Phillips

Screwdrivers1½" Wood ScrewsWire Strippers Wire Connectors

Appropriate

Connector

Volt Meter

Drill and Drill Bits

Stud Finder

Hammer

INSTALLATION INSTRUCTIONS

1. All electrical work and materials

must comply with the National

Electric Code (NEC), the

Occupational Safety and Health

Act (OSHA), and all state and

local codes.

2. Use copper conductors only.

3. DO NOT install the heater directly

above bathtub or sink. DO NOT

install in shower stall area.

(Manufacturer recommends

a minimum 2 foot (61 cm)

clearance to prevent contact with

water.)

4. A GFCI protected branch circuit

is recommended when installed

in a wet or damp area.

5. Heater must be installed against

a rigid surface.

6. DO NOT install the heater

anywhere the air discharge may

be blocked in any manner.

7. To reduce the risk of ﬁre, do not

store or use gasoline or other

ﬂammable vapors and liquids in

the vicinity of the heater.

8. Connect grounding lead to

grounding screw provided. Keep

all foreign objects out of heater.

PARTS OF YOUR HEATER

high-temperature

safety shuto󰀨

TOP VIEW (FP102 PICTURED)

heater

element(s)

built-in

thermostat

This heater is speciﬁcally designed for frost protection. It is approved for use in unclassiﬁed locations

in accordance with the National Electrical Code (NEC), ANSI/NFPA 70. It is not approved for

residential heating.

Models FP052TB and FP102TB can be connected to 240 or 208 volts.

Model FP051TB is for 120 volts only. Please don’t assume you have 120 volts because your wires are

black and white.

This heater must be installed by a licensed electrician in accordance with these instructions and all

local codes, or in their absence, in accordance with the latest editions of the International Residential

Code and International Electrical Code. Always disconnect the heater from its power source before

servicing. Ensure that the heater is installed in a location to allow ease of access for repair and

maintenance.

INSTALLATION INSTRUCTIONS

Mount the heater to a rigid, non-combustible surface. There are six holes located on the mounting

surface. Please use any two holes that are as far apart as practical. For a crawl space, mount to the

concrete foundation wall. The heater may be mounted on brick or concrete block. The heater must be

mounted in a space with adequate venting and ground insulation that meets or exceeds local building

codes.

In the absence of a local building code, the heater can only be mounted with the following conditions:

1. Only crawl spaces under 1-story or 2-story portions of dwelling units shall be used.

2. Enclosing material in crawl spaces shall have a surface ﬂame-spread rating not greater than 150.

3. Combustible ground cover used as enclosing material in Sentence (2) shall be covered with non-

combustible material. Non-combustible material shall,

(a) extend not less than 12 inches (30 cm) beyond the projection of a register opening, and

(b) have turned-up edges.

OVERVIEW

0" minimum

to adjacent

surface

3" (7.6 cm) minimum;

24" (60.9 cm) maximum to floor

12" (30.4 cm) minimum above

0" minimum

to adjacent

surface

Clearances

Do not block the inlet vents on the bottom surface. There must be a minimum of 3 inches (7.6 cm)

below the bottom vents and 12 inches (30.4 cm) above the top vents for proper airﬂow and heating.

KNOW YOUR VOLTAGE and CHECK YOUR BREAKER!

All heaters require three supply wires. For 120 volt wiring you will have 1 hot, 1 neutral and 1 ground.

For 240 and 208 volt wiring you will have 2 hot wires and 1 ground; no neutral needed.

1. Turn o󰀨 the electrical power supply. If required, install a new circuit breaker and route electrical

wires to the heater.

2. Remove the cover. Wire connections are made on the left side of the heater.

3. Install all necessary conduit and connectors (not included). Rigid or ﬂexible conduit may be used.

Leave 6 inches (15.2 cm) of available supply wire for connecting to the heater. The ﬁeld wiring must

include a ground wire connected to the inside of the junction box.

4. Pull supply wires through the conduit leaving 6-inch wire leads.

Connect one supply wire to one of the heater wires with a wire connector (not included).

a. For 240 and 208 volts, it doesn’t matter which heater wire. Both supply wires (black and white)

are hot. Wrap supply (white) wire with black tape to identify it as hot

b. For 120 volts, connect the neutral (white) supply wire to the white heater wire.

5. Connect remaining supply wire to remaining heater wire with a wire connector (not included).

6. Install the cover. Turn power back on at the main disconnect panel.

1. The heater must be properly

installed before it is used.

2. Do not operate without cover.

3. Do not tamper with high

temperature safety shuto󰀨.

4. The heater knob has a

temperature range of 40°F (4°C)

to 85°F (30°C). The heater will

not heat if turned fully counter

clockwise.

OPERATING INSTRUCTIONS

Complete installation

After installation, turn your heater to the highest setting and let it run for 30 minutes. Some smoking

may occur as the element initially burns o󰀨 residue from manufacturing.

If your heater shows signs of overheating, such as glowing red or repeatedly getting unusually hot

and shutting o󰀨, immediately turn o󰀨 the circuit breaker and review the “KNOW YOUR VOLTAGE”

section or call us.

If the high-temperature safety shuto󰀨 trips more than once a day, replace the heater.

How to operate your heater

The heater is controlled with the built-in thermostat located on the right end of the heater. The

thermostat has a range from 40°F (4°C) to 85°F (30°C) starting at the second smallest dot.

IMPORTANT: The heater will not operate if set to the smallest dot on the dial.

Since each application is unique, please adjust the thermostat above the second dot to meet your

particular requirements. A wall thermostat may not be used.

WARRANTY

For more e󰀨ective and safer operation and to

prolong the life of the heater, read the Owner’s

Guide and follow the instructions. Failure to

properly maintain the heater will void any warranty

and may cause the heater to function improperly.

LIMITED TWO YEAR WARRANTY: Cadet will

repair or replace any Frost Protection (FP) heater

found to be defective within two years after the

date of purchase.

These warranties do not apply:

1. Damage occurs to the product through improper

installation or incorrect supply voltage;

2. Damage occurs to the product through

improper maintenance, misuse, abuse, accident,

or alteration;

3. The use of unauthorized accessories or

unauthorized components constitutes an

alteration and voids all warranties. Refer to Cadet

website or call customer service at 855.223.3887

or 360.693.2505 for list of authorized accessories

and components.

4. Cadet’s warranty is limited to repair or

replacement.

5. In the event Cadet elects to replace any part

of your Cadet product, the replacement parts are

subject to the same warranties as the product.

The installation of replacement parts does not

modify or extend the underlying warranties. Re-

placement or repair of any Cadet product or part

does not create any new warranties.

If you believe your Cadet product is defective,

please contact Cadet during the warranty period,

for instructions on how to have the repair or

replacement processed.

Parts and Service

Visit cadetheat.com/parts-service for information

on where to obtain parts and service.

To register your product, visit cadetheat.com/product-registration

INTERNAL HEATER WIRING DIAGRAMS

L2/N

HIGH

TEMPERATURE

SAFETY SWITCH

ADJUSTABLE

THERMOSTAT

40°F - 85°F

(4°C - 30°C)

HIGH

TEMPERATURE

SAFETY SWITCH

ADJUSTABLE

THERMOSTAT

40°F - 85°F

(4°C - 30°C)

L2/N

HIGH

TEMPERATURE

SAFETY SWITCH

ADJUSTABLE

THERMOSTAT

40°F - 85°F

(4°C - 30°C)

HIGH

TEMPERATURE

SAFETY SWITCH

ADJUSTABLE

THERMOSTAT

40°F - 85°F

(4°C - 30°C)

FP102T (dual element)FP051T FP052T (single element)

MAINTAINING YOUR HEATER

Clean heater at least every 6 months or as required. The heater must be

inspected every 6 month or more if conditions warrant it. It is essential that

the heater is not operated with an accumulation of dust, dirt or debris on the

heater or inside the heating chamber.

1. Turn o󰀨 power at the main disconnect panel.

2. Wait for the heater to cool.

3. Clean the unit with a damp cloth.

4. Turn power back on at the main disconnect

panel.

Any service other than cleaning should be performed by an authorized

service representative.

High-temperature safety shuto󰀨

All Frost Protection heaters come with a built-in high-temperature safety shuto󰀨 that stops electricity

ﬂowing to the heater if it gets too hot inside. This automatically resets after cooling.

Reduce-Reuse-Recycle

This product is made primarily of recyclable materials. You can reduce your carbon footprint by recycling

this product at the end of its useful life. Contact your local recycling support center for further recycling

instructions.

Rev 03/25/19 #720136

If you are uncomfortable working with electricity, running electrical supply

wire or installing a circuit breaker, please consult a licensed electrician.

CLEANING INSTRUCTIONS

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Calentador de Cadet

Cadet

Cadet NLW208T Manual de usuario

Cadet

Cadet The Com-Pak CBC132TW Manual de usuario

Cadet

Cadet COM-PAK MAX CM192 Manual de usuario

Cadet

Cadet Com-Pak CBC132TW Manual de usuario

Cadet

Cadet Energy Plus CE163T Manual de usuario

Cadet

Cadet RM151 Manual de usuario

Cadet

Cadet Apex72 Manual de usuario

Cadet

Cadet Energy Plus CE083T Manual de usuario

Cadet

Cadet SOFTHEAT PORTABLE Manual de usuario

Cadet

Cadet CE163T Manual de usuario

Cadet

Cadet SL101T Manual de usuario

Cadet

Cadet CE083T Manual de usuario

Cadet

Cadet CM162 Manual de usuario

Cadet

Cadet CGH562 Manual de usuario

Cadet

Cadet CEH-003M Manual de usuario

Cadet

Cadet Apex72 HW162 Manual de usuario

Cadet

Cadet RBF Series Manual de usuario

Cadet

Cadet SoftHEAT Manual de usuario

Cadet

Cadet softHEAT EBHN500-1 Manual de usuario

Cadet

Cadet The Perfectoe UC072 Manual de usuario

Cadet

Cadet The Com-Pak Plus C072 reset Manual de usuario

Cadet

Cadet SL Series Manual de usuario

Cadet

Cadet softHEAT EBHN500-1 Manual de usuario

Cadet

Cadet FW051 Manual de usuario

Manuales populares de Calentador de otras marcas

oventrop

oventrop Regucor Series Manual de usuario

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manual de usuario

ELMEKO

ELMEKO ML 150 Manual de usuario

BN Thermic

BN Thermic 830T Manual de usuario

KING

KING K Series Guía

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guía de inicio rápido

Well Straler

Well Straler RC-16B Manual de usuario

EUROM

EUROM 333299 Manual de usuario

Heylo

Heylo K 170 Manual de usuario

Eterna

Eterna TR70W Manual de usuario

Clarke

Clarke GRH15 Manual de instrucciones

IRSAP

IRSAP The Radiator Company Ovali Manual de usuario

Empire Heating Systems

Empire Heating Systems WCC65 Manual de usuario

Wetekom

Wetekom 92 86 43 Manual de usuario

Desa

Desa SPC170-F Manual de usuario

Watlow

Watlow Watrod Electric Tubular Heaters Manual de usuario

Haverland

Haverland ECO-DRY GPS Series Manual de lista de piezas

Stelpro

Stelpro ASILVC2060 Series Manual de usuario