Cabletron Systems 9A426-02 Manual de usuario

9031918-03

SmartSwitch 9000

9A426-02

User’s Guide

Notice

Cabletron Systems reserves the right to make changes in speciﬁcations and other information

contained in this document without prior notice. The reader should in all cases consult Cabletron

Systems to determine whether any such changes have been made.

The hardware, ﬁrmware, or software described in this manual is subject to change without notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT,

SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED

TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION

CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR

SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.

Cabletron Systems, Inc.

35 Industrial Way

Rochester, NH 03867-5005

Printed in the United States of America

Order Number: 9031918-03

LANVIEW

is a registered trademark, and

SmartSwitch

is a trademark of Cabletron Systems, Inc.

CompuServe

is a registered trademark of CompuServe, Inc.

i960 microprocessor

is a registered trademark of Intel Corp.

Ethernet

is a trademark of Xerox Corporation.

Notice

FCC Notice

This device complies with Part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

NOTE:

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial environment.

This equipment uses, generates, and can radiate radio frequency energy and if not installed in

accordance with the operator’s manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause interference in which case the user

will be required to correct the interference at his own expense.

WARNING:

Changes or modiﬁcations made to this device which are not expressly approved by the

party responsible for compliance could void the user’s authority to operate the equipment.

VCCI Notice

This equipment is in the 1st Class Category (information equipment to be used in commercial and/or

industrial areas) and conforms to the standards set by the Voluntary Control Council for Interference

by Information Technology Equipment (VCCI) aimed at preventing radio interference in commercial

and/or industrial areas.

Consequently, when used in a residential area or in an adjacent area thereto, radio interference may be

caused to radios and TV receivers, etc.

Read the instructions for correct handling.

DOC Notice

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital

apparatus set out in the Radio Interference Regulations of the Canadian Department of

Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables

aux appareils numériques de la class Aprescrites dans le Règlement sur le brouillage radioélectrique

édicté par le ministère des Communications du Canada.

iii

Notice

DECLARATION OF CONFORMITY

Application of Council Directive(s):

89/336/EEC

73/23/EEC

Manufacturer’s Name:

Cabletron Systems, Inc.

Manufacturer’s Address:

35 Industrial Way

PO Box 5005

Rochester, NH 03867

European Representative Name:

Mr. J. Solari

European Representative Address:

Cabletron Systems Limited

Nexus House, Newbury Business Park

London Road, Newbury

Berkshire RG13 2PZ, England

Conformance to Directive(s)/Product Standards:

EC Directive 89/336/EEC

EC Directive 73/23/EEC

EN 55022

EN 50082-1

EN 60950

Equipment Type/Environment:

Networking Equipment, for use in a

Commercial or Light

Industrial Environment.

We the undersigned, hereby declare, under our sole responsibility, that the equipment packaged with

this notice conforms to the above directives.

Manufacturer Legal Representative in Europe

Mr. Ronald Fotino Mr. J. Solari

____________________________________________________ ______________________________________________________

Full Name Full Name

Principal Compliance Engineer Managing Director - E.M.E.A.

____________________________________________________ ______________________________________________________

Title Title

Rochester, NH, USA Newbury, Berkshire, England

____________________________________________________ ______________________________________________________

Location Location

Notice

Contents

Chapter 1 Introduction

Features...........................................................................................................................1-2

Related Manuals............................................................................................................1-4

Getting Help .................................................................................................................. 1-4

Chapter 2 Preparing and Installing

the 9A426-02 Module

Unpacking the Module.................................................................................................2-1

The Module’s Physical Layout....................................................................................2-1

User-Accessible Components on the Module’s Motherboard................................2-2

Look-Up Engines ...................................................................................................2-3

SRAM SIMMs.........................................................................................................2-4

APIMs......................................................................................................................2-4

Installing an APIM in the 9A426-02 Module............................................................. 2-4

Unpacking an APIM..............................................................................................2-5

Removing the 9A426-02 Module’s ATM-Port Retaining Plate........................ 2-5

Inserting an APIM into the 9A426-02 Module...................................................2-7

Attaching the 9A426-02 Module’s ATM-Port Retaining Plate ........................2-8

User-Accessible Components on the Module’s Daughterboard............................2-9

DIP Switch.............................................................................................................2-10

Removing the Daughterboard from the Motherboard...................................2-12

Installing the Module into the SmartSwitch 9000 Chassis....................................2-15

The Reset Switch ......................................................................................................... 2-18

Chapter 3 Operation

LAN Emulation.............................................................................................................3-3

System Management Buses .........................................................................................3-3

SMB-1 Bus...............................................................................................................3-3

SMB-10 Bus.............................................................................................................3-4

System Diagnostic Controller...................................................................................... 3-4

DC/DC Converter ........................................................................................................3-4

INB Network Interface Block ......................................................................................3-4

FDDI Network Interface Block.................................................................................... 3-5

ATM Network Interface Block ....................................................................................3-5

SecureFast Virtual Networking...................................................................................3-5

i960 Core......................................................................................................................... 3-6

Contents

Chapter 4 LANVIEW LEDs

Chapter 5 Speciﬁcations

Technical Speciﬁcations................................................................................................5-1

CPU..........................................................................................................................5-1

Memory ...................................................................................................................5-1

Address Table Size .................................................................................................5-1

Power.......................................................................................................................5-1

Network Interfaces ................................................................................................5-1

Standards.................................................................................................................5-2

Safety...............................................................................................................................5-2

Service.............................................................................................................................5-2

Physical...........................................................................................................................5-3

Dimensions .............................................................................................................5-3

Weight......................................................................................................................5-3

Environment...........................................................................................................5-3

1-1

Chapter 1

Introduction

The 9A426-02 ATM Module is a hardware-based switching module that supports

multiple interfaces simultaneously. The module’s interconnecting interfaces

include:

• Up to two front panel ATM interfaces via user-installed ATM Port Interface

Modules (APIMs)

• A ﬁxed interface to the SmartSwitch 9000’s Internal Network Bus (INB)

• A user-conﬁgurable interface to the SmartSwitch 9000’s Flexible Network Bus

(FNB-1 or FNB-2)

Each data packet, regardless of the interface in which the packet enters the

module (ATM, FNB, or INB), is initially converted into a common format known

as a canonical frame. Each canonical frame’s header section contains source and

destination information. All canonical frames are forwarded to the module’s

group of SmartSwitch Application Speciﬁc Integrated Circuits (ASICs)

collectively known as the SmartSwitch Core.

The SmartSwitch Core can process data in two modes: as a traditional switch or as

a Secure Fast Switch (SFS). When operating as a traditional switch, the Fast Packet

Switch makes ﬁltering/forwarding decisions based on Destination Address, with

standard IEEE 802.1d learning. When operating in SFS mode, all

ﬁltering/forwarding decisions are based on a Destination Address-Source

Address pair, and the associated receive/transmit port.

Canonical frames that enter the 9A426-02 Module via the backplane interface

(FNB or INB) and are destined for the module’s front panel interface(s), are

converted by the module’s ATM Network Interface Block (ANIB) into 53 byte

ATM cells. The ANIB uses a separate set of ASICs to perform hardware-based

packet to cell conversions. This conversion process is an integral part of the

module’s ability to provide high-performance interconnections between legacy

LANs and ATM attached networks.

Introduction

1-2

Conversely, canonical frames destined for the FNB bus on the SmartSwitch 9000

backplane are converted into FDDI packets via the 9A426-02 Module’s FDDI

Network Interface Block (FNIB), and then forwarded onto the FNB.

Canonical frames destined for the INB bus on the SmartSwitch 9000 backplane are

converted into ﬁxed length data packets via the 9A426-02 Module’s INB Network

Interface Block (INB NIB), and then forwarded onto the INB.

Features

Processor

The 9A426-02 Module is equipped with an advanced Intel i960 microprocessor.

This microprocessor provides a platform for all management functions within a

scalable RISC-based architecture.

SmartSwitch Core

The 9A426-02 Module incorporates the SmartSwitch Core, a collection of custom

Application Speciﬁc Integrated Circuits (ASICs) designed speciﬁcally for high

speed switching. The SmartSwitch ASIC bus is 64 bits wide with a bandwidth of

640 Mbps. Since all frame translation, address lookups, and forwarding decisions

are performed in hardware, the 9A426-02 Module can obtain a throughput

performance of greater than 750K pps.

Management

The 9A426-02 Module has one full implementation of SMT (Version 7.3) and

SNMP for local and remote management. Local management is provided through

the RS-232 Com ports on the SmartSwitch 9000 Environmental Module using a

standard VT-220™ terminal or emulator, or via telnet. Remote management is

achieved through Cabletron’s SPECTRUM or any SNMP compliant management

tool. Switching statistics of the selected FNB interface include frames ﬁltered,

frames forwarded, and all Spanning Tree Protocol parameters.

Connectivity

The 9A426-02 Module has two front panelATM interfaces. AnATM Port Interface

Module (APIM) can be installed in one (or both) interface(s). The 9A426-02

Module also has one interface to the INB-2 backplane, and one user-conﬁgurable

interface to the SmartSwitch 9000 FNB backplane (either FNB-1 or FNB-2, or

neither).

Management Information Base (MIB) Support

The 9A426-02 Module provides MIB support including:

• IETF AToM MIB

• IETF FDDI MIB

• IETF Bridge MIB

• A host of Cabletron Enterprise MIBs

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Cabletron Systems

Cabletron Systems

Cabletron Systems TRFMIM 28 TRFMIM-28 Manual de usuario

Cabletron Systems

Cabletron Systems 7C03 MMAC SmartSWITCH Manual de usuario

Cabletron Systems

Cabletron Systems SmartSwitch 6E122 Manual del propietario

Cabletron Systems

Cabletron Systems 2E43-51 Manual de usuario

Cabletron Systems

Cabletron Systems 6A000/ZX-250 Manual de usuario

Cabletron Systems

Cabletron Systems MicroMMAC-24E Manual de usuario

Cabletron Systems

Cabletron Systems SmartSwitch 9W006 Manual de usuario

Cabletron Systems

Cabletron Systems CyberSWITCH CSX1200 Manual de usuario

Cabletron Systems

Cabletron Systems MMAC-Plus 9EX02-12 Manual de usuario

Cabletron Systems

Cabletron Systems Spectrum 2E42-27 Manual de programación

Cabletron Systems

Cabletron Systems SmartSTACK ELS10-27MDU Instrucciones de instalación y funcionamiento

Cabletron Systems

Cabletron Systems TRXI-22 Manual de usuario

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Instrucciones de montaje

Cabletron Systems

Cabletron Systems SEHI SEHI100TX- Manual de usuario

Cabletron Systems

Cabletron Systems SmartSTACK ELH100 Manual de usuario

Cabletron Systems

Cabletron Systems MMAC-Plus 9T125-08 Manual de usuario

Cabletron Systems

Cabletron Systems MMAC-Plus 9T122-24 Manual de usuario

Cabletron Systems

Cabletron Systems 2208 Manual de usuario

Cabletron Systems

Cabletron Systems SMALL OFFICE CyberSwitch 150 Manual de usuario

Cabletron Systems

Cabletron Systems SmartSwitch 6500 Manual de usuario

Cabletron Systems

Cabletron Systems SmartSTACK 100 ELS100-24TX Instrucciones de instalación y funcionamiento

Cabletron Systems

Cabletron Systems SynOptics 3000 Series Manual de usuario

Cabletron Systems

Cabletron Systems IA1100 Manual de usuario

Cabletron Systems

Cabletron Systems SPECTRUM 1800 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario