C-Bus 5200PG Manual de usuario
Wiser Home Control
5200PG5200PG
Installation Instructions
Wiser Home Controller Installation Instructions
2
© Copyright Clipsal Australia Pty Ltd, 2009. All rights reserved. This material is
copyright under Australian and international laws. Except as permitted under the
relevant law, no part of this work may be reproduced by any process without prior
written permission of and acknowledgement to Clipsal Australia Pty Ltd.
Clipsal and C-Bus are registered trademarks of Clipsal Australia Pty Ltd.
The information in this manual is provided in good faith. Clipsal Australia Pty Ltd
(CAPL) has endeavoured to ensure the relevance and accuracy of the information,
but it assumes no responsibility for any loss incurred as a result of its use. CAPL
does not warrant that the information is fit for any particular purpose, nor does it
endorse its use in applications that are critical to the health or life of any human
being. CAPL reserves the right to update the information at any time without notice.
Release date: March 2009.
Wiser Home Controller Installation Instructions
3
Contents
1.0 Product Description 5
1.1 Hardware Components 5
1.2 Software 7
1.3 Product Information 8
2.0 Network Topology 9
2.1 Mapping Your Existing Network 9
2.2 Adding the Wiser Home Controller and CNI 10
2.3 Setting up a Wireless LAN 13
3.0 Installation 14
3.1 Installation Location 14
3.2 Important Notes 14
3.3 Overview of Hardware Installation Steps 15
3.4 Step 1, Connect the CNI to the
C-Bus Network Cable 16
3.5 Step 2, Assemble the Router, CNI and Busbar 17
3.6 Step 3, Install the Hardware 18
3.7 Step 4, Connect Your Configuration PC 19
4.0 Software Configuration 22
4.1 Step 1, Configure the Wiser Home Controller
Router 22
4.2 Step 2, Use C-Bus Toolkit to Collect
Project Information 26
4.3 Step 3, Use PICED to Create and Transfer
a Project 27
5.0 Introduction to the User's Interface (UI) 32
6.0 Additional Information 34
6.1 Using Static TCP/IP Settings on
the PC (if necessary) 34
Wiser Home Controller Installation Instructions
4
6.2 Useful MS-DOS Command Prompt Programs 36
6.3 Frequently Asked Questions (FAQs) 37
6.4 Release Notes 41
7.0 Terms 43
8.0 Product Specifications 44
9.0 Standards Complied 45
10.0 GNU General Public Licence 47
11.0 Two-Year Warranty 49
Wiser Home Controller Installation Instructions
5
1.0 Product Description
The 5200PG Wiser Home Controller provides an easy-to-use graphical
user interface (GUI) to access the home C-Bus network and other home
applications. The Wiser Home Controller lets you monitor and control your
home environment locally, or remotely over the Internet.
Using the Wiser Home Controller, you can locally or remotely
• Configure and commission certain aspects of lighting, security and
environmental equipment using C-Bus Toolkit and PICED software
products.
• Recognise and utilise C-Bus TAG descriptions, Locations and
Function Groups.
• Back up and restore projects to and from a PC.
• Control and monitor C-Bus lighting scenes on C-Bus networks.
• Create, trigger and control scenes.
• Control and monitor HVAC equipment.
• Interface with security panels and cameras.
1.1 Hardware Components
Component Description or Characteristics
Wiser Home
Controller router The Wiser Home Controller router provides
• A wired connection to the customer’s Internet.
• A wired connection to the CNI for C-Bus network access.
• A wireless 802.11 LAN set up for WPA encryption.
• Four wired LAN ports (one is reserved for the CNI).
C-Bus Network
Interface (CNI)
The inline CNI connects to
• A Wiser Home Controller router LAN port.
• The C-Bus network using a Cat.5e cable, twisted pairs
1 GB USB drive Includes readme.htm, Installation Instructions and User's
Guide
Power supply The supply provides d.c. power for the router and CNI
Busbar The busbar provides a simplified power and signal
connection for the Wiser Home Controller router and CNI.
Wiser Home Controller Installation Instructions
6
Cat.5e network
cable
The blue or black network cable connects the customer's
broadband device to the Wiser Home Controller's router. Do
not use this cable for C-Bus connections.
Link The link comes attached to the CNI and locks the Wiser
Home Controller and CNI together to form a single unit.
Support stand The optional stand is useful when placing the Wiser Home
Controller on a table or desk. (Not shown in Figure 1.)
Setup Sheet The Setup Sheet provides quick instructions for installation
and configuration.
Table 1. Hardware components
Figure 1. Wiser Home Controller hardware components
To avoid equipment damage, you must install the three supplied
antennas before connecting the power supply to the Wiser Home
Controller router.
Wiser Home Controller Installation Instructions
7
1.2 Software
Normally, the installer loads PICED and C-Bus Toolkit on a PC and brings it
to the customer site.
Software Applications
When installing the Wiser Home Controller, you must use the downloaded
versions of the following Clipsal software applications:
• PICED setup software, version 4.5, or later. Access the PICED
software using the link in the readme.htm file located on the
provided Wiser USB drive.
• C-Bus Toolkit setup software, version 1.10.2, or later. The latest
C-Bus Toolkit version is available at the Clipsal Integrated Systems
technical downloads site:
http://www2.clipsal.com/cis/technical/ select Downloads.
You must use the latest PICED software to obtain the latest firmware and
the automatic firmware update feature. If you are unsure about the
correct software versions to use, contact Technical Support.
The PICED setup software contains the latest Wiser Home Controller
firmware .IMG file. The latest firmware is loaded automatically as part of
transferring your PICED project to the Wiser Home Controller. The setup
packages also include the latest CNI configuration software, C-Gate and
transfer utilities. Refer to Section 4.3.
Graphical User Interface (GUI)
After configuring the Wiser Home Controller, your entry point to the Wiser
Home Controller is the Wiser Graphical User Interface (GUI). Refer to
Section 5.0 for more information about using the GUI. The factory installs
the GUI and a sample project in the Wiser Home Controller router. The
sample project is not intended to be used as is; you must create a new
project with PICED.
To access the GUI, connect to the LAN and open a browser session. Clipsal
recommends using Internet Explorer or Mozilla Firefox. Type the following
IP address and press Enter:
http://192.168.2.1
The username is admin and the password is admin
Wiser Home Controller Installation Instructions
8
1.3 Product Information
The following documents and online files are available from the downloads
site noted previously:
C-Bus Wiser Home Controller 5200PG Setup Sheet
The Setup Sheet provides quick installation information for installers who
are familiar with home LANs. The Setup Sheet is shipped with the product.
C-Bus Wiser Home Controller 5200PG Installation Instructions
A copy of this document is shipped with the product on a USB drive. You
can download the latest version of the document from the CIS technical
download site as a PDF file.
C-Bus Wiser Home Controller User's Manual
This document is provided on a USB drive with your equipment. The User's
Manual is a handy reference when configuring the Wiser Home Controller
and developing programs that control C-Bus equipment in the home. The
latest version of the document can be downloaded from the Clipsal CIS
downloads site as a PDF file.
readme.htm
file for the Wiser Home Controller
The readme.htm file provides a link to the download site for the latest
PICED software setup package. The readme.htm file is provided on the
Wiser 1GB USB drive that is provided with the unit.
C-Bus Toolkit Help
C-Bus Toolkit Help is part of the software setup. The latest version has
current GUI and device content. Help is available whenever C-Bus Toolkit is
running.
PICED Help
When using PICED, you should access Help as needed to create your
projects. Help provides information about the toolbars and menus.
Other Help files
Clipsal software products such as C-Gate and the CNI Configuration Utility
have help files that can be very useful during installation and
troubleshooting.
Wiser Home Controller Installation Instructions
9
2.0 Network Topology
You should carefully consider the existing network layout at the customer
site before installing the Wiser Home Controller. Try to minimise the
amount of reconfiguration required. There are a couple of important points
to remember during the Wiser Home Controller installation.
• The Wiser Home Controller is not a modem. You must connect the
router to an Internet connection, NOT a telephone line. A
broadband modem is not provided as part of Wiser Home
Controller.
• The Wiser Home Controller has wired and wireless LAN capabilities.
The CNI uses one wired router LAN port. The three remaining wired
ports are for IP connections to the local LAN.
2.1 Mapping Your Existing Network
There are many variations found in home networks. By mapping the
existing network, you make it much easier to see what cabling and
configuration tasks must be performed when installing the Wiser Home
Controller.
Example:
The figure below shows a basic network configuration that is common in
many homes. The network might use automatic IP addressing (DHCP), static
IP addressing or a mix of the two.
Figure 2. A basic home network example BEFORE installing a Wiser Home Controller
In the example above, the customer can easily access the static IP address
of the modem/router to set wireless security parameters.
Wiser Home Controller Installation Instructions
10
2.2 Adding the Wiser Home Controller and CNI
The installer has several choices when adding the Wiser Home Controller to
the customer's network. The basic options are:
• Option A. Connect the Wiser Home Controller's WAN port to the output
of the customer's modem/router as shown in Figure 3. In this
configuration, all network traffic passes through the Wiser Home
Controller's wired and wireless LANs.
• Option B. Place the Wiser Home Controller on the existing customer
LAN as shown in Figure 4. This configuration allows you to make
minimal changes to the customer's equipment setup.
• Option C. Connect the Wiser Home Controller to an ADSL modem in
bridge mode. In this configuration, the Wiser Home Controller is the
direct gateway to the customer's ISP.
Option A
Figure 3. Option A, Wiser Home Controller as the connection point for the
customer's LAN
When using Option A, you must re-establish the IP addresses of the
customer's IP connected devices to subnet 2. You might have to configure
static IP addresses. If you are using wireless devices, you must also
configure the wireless LAN on the Wiser Home Controller.
If the Wiser Home Controller does not provide enough physical connections
for IP connected devices, a hub must be added. Clipsal does not provide the
hub.
Otros manuales para 5200PG
1
Tabla de contenidos
Manuales populares de Sistema de seguridad de otras marcas
EDM
EDM Solution 6+6 Wireless-AE Manual de usuario
Highway Safety Group
Highway Safety Group EA401 Manual de usuario
Siren
Siren LED GSM Manual de usuario
Detection Systems
Detection Systems 7090i Instrucciones de montaje
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manual de usuario
Siemens
Siemens FDM273 Manual de usuario