C & K Systems System 238 Manual de usuario

SYSTEM 238 Installation Manual

BLK

RED

BATTERY

DIRECT

CONNECT

DS1

WATCH

DOG T1

TB1

DEVICES

UNSWITCHED

AUX

POWER

- Protected by

Fuse F2:

3 AG, 0.75 A

- Shared with

keypads and

AUX POWER

KEYPAD

INFORMATION

- Do not exceed

4 keypads or

max AUX POWER

- Protected by Fuse

F3: 3 AG, 0.75 A

WARNINGS:

- For continued protection

against risk of fire, replaces

fuses only with fuses of same

type and rating

- Disconnect AC, battery, and

phone cord BEFORE servicing

2.2K

EOL 2.2K

EOL

2.2K

EOL

2.2K

EOL

2.2K

EOL

2.2K

EOL

2.2K

EOL 2.2K

EOL

Capacity for

emergency standby

at least 4 hours

- Connect ground wire from door hinge to earth ground using

16 AWG, green jacketed, solid-conductor wire

GENERAL INFORMATION

- All outputs are power limited

- If programmed for EOL or Supervised loop, the 2.2K ohm EOL

resistor (Model 9.X, 2.2K) must be at end of circuit

- Loop 8 can be used as standard loop or used for switched 10-

12.5 VDC at 50 mA for 2-wire powered devices. Loop 8 can

support up to 10 BRK Model 2400 2-wire smoke detectors.

- Loop voltages:

Loops 1 - 8

0 - 2.5 VDC = short

2.5 - 8.5 VDC = normal

8.6 - 15 VDC = open

- Install transformer on unswitched power receptacle

- Only use 12 VDC, 6.5 AH sealed lead-acid battery

POWER SUPPLY INFORMATION

- Replace battery every 3 - 5 years with C&K Model 1265

- Standby time with 1 keypad is 16 hours at 250 mA

- Power demand for AUX POWER, keypads, and sounders

not to exceed maximum ratings

Fuse F4

3 AG, 3 A

battery

protection

- are electrically common

AUDIBLE

10.5-13.5 VDC

Protected by

Fuse F1: 3AG,

2.5 A

16.5 VAC

25 - 40 VA

50 / 60 Hz

SWITCHED

AUX

POWER

P/N 5-051-162-00 Rev J

All ratings listed on this page are in compliance

with UL 985, UL 1023, and UL 1635.

NOTE:

To be in compliance with UL 365 and UL 609,

total power from Sw/Aux, Aux, and Key+

Terminals not to exceed 150 mA combined.

AUXCCACAC +-+-+ +-++- ++- -++

BELL SW/AUX KEY+ DATA CLK C

Z1 Z2 Z3 C Z4 Z5 C Z6 Z7

++C Z8 Tip Ring T1 R1

PHONE

CORD

- 9.X PCF Red = incoming ring

Green = incoming tip

Gray = seized ring

Brown = seized tip

Blue = tamper

Orange = tamper

WARNING: Circuit Damage May Result

From Incorrect Wiring Connections.

- Remove AC and battery power before replacing fuses

- Maximum battery charge current = 350 mA

CAUTION:

Total power from Bell, Sw/Aux, Aux and

Key+ Terminals NOT to exceed 1.3 A,

combined (also seeNOTE: below)

12 VDC

6.5 AH

sealed lead-acid

SYSTEM 238 Installation Manual

Subject Page No.

System 238 Terminal Label Front Cover

UL Compliance 2

Installation 2 - 3

Wiring the Panel 3 - 4

System Start-Up 4

Keypad Setup 4 - 5

Addressing Keypads 5

Factory Default Settings 5

Programming Options (Alphabetical List) 5 - 6

Programming the Panel 6

Programming with the LED Keypad 6

Programming with the Alpha Keypad 6

Entering Hexadecimal Numbers 6

Programming the Alpha Keypad 6 - 7

Programming Letters & Numbers 7

Special Function Keys 7

Programming Options (Numerical Order) 8-18

Keypad Label Drawer 19

Telephone Line Problems 19

Watchdog Indicator 19

Keypad Operation Command Summary 20

Help with Common Problems (Troubleshooting) 21 - 22

Reducing False Alarms 23 - 24

Warranty Information 25

Programming Worksheets 26 - 27

Table of Contents

Scope of This Manual

This manual contains basic installation and programming information

for the SYSTEM 238. For additional information about using or

programming the system, please refer to the SYSTEM 238 Keypad

Manual, Alpha Keypad Manual, or Commander II/Monitor II Operating

Manual.

BEFORE YOU START

12. The unit must not be programmed to dial a police station.

13. Use screws (supplied) to secure cover or a lock must be

installed on the cabinet.

14. All devices must be UL listed.

Accuracy

This manual has been carefully checked for accuracy. However, C&K

SYSTEMS assumes no liability for inaccuracies or actions resulting

from the use of this manual. In addition, C&K reserves the right to

modify the SYSTEM 238 hardware, software, and manuals without

prior notice.

The SYSTEM 238 is in compliance with Underwriters Laboratories,

Inc. Standards UL 985, Household Warning System Units; UL 1023,

Household Burglar Alarm System Units; and UL 1635, Digital Burglar

Alarm Communicator System Units. The following programming

restrictions must be observed to meet UL standards.

UL COMPLIANCE

1. The audible must be programmed to sound at least four

minutes before silencing.

2. No zone may be programmed for silent alarm.

3. Fire zones must be programmed for pulsing audible alarm.

4. Burglar zones must be programmed for a steady audible.

5. Burglar loops (non-24-hour loops) must be programmed

for NO/NC with EOL.

6. No Entry Delay may be greater than 45 seconds.

7. No Exit Delay may be greater than 60 seconds.

8. The Dynamic Battery Test must be enabled.

9. The Unit Status Report must be enabled.

10. The 24-hour Check-in must be enabled.

11. No Delay Before Dial may be programmed for the

communicator.

The following additional restrictions must be observed to meet

Grades A and B Mercantile Premises Alarm Systems/Safe and

Vault Alarms Systems under UL 365, Police Station Connected

Burglar Alarm Units and Systems and UL 609, Local Burglar Alarm

Units and Systems.

Mounting

The SYSTEM 238 should be mounted in a location which allows

convenient access to AC power, telephone connections, and earth

ground.

• Remove the circuit board from the cabinet. This will prevent

possible damage to the circuit board when removing the knock-

outs.

• Remove the knock-outs.

• Mark the screw mounting holes on the wall.

• Mount the cabinet at the desired height and pass the cables

through the knock-outs.

• Replace the circuit board, remembering to connect the ground lug

to the lower left corner of the circuit board.

• Reconnect thespadelugtothelowerdoorhinge.This providesthe

earth ground connection for the door.

INSTALLATION

Keypad Requirements

The keypad may not have the EMERGENCY symbol ( ) on it. If your

keypad has this symbol, remove the key and replace it with one of the

blank keys provided.

Not shuntable

Supervised

- latching for heat

- resetting for smoke

.NO/NC with EOL

Pulsing audible

.Steady Audible

24-hour arming

.No Delay Before Dial

No Delay Before Dial

.BURGLAR LOOP

FIRE LOOP

Zone Programming

1. The audible must be programmed to sound at least 15 minutes

before silencing.

2. The ring-back function must be activated.

3. The control panel must be mounted in an enclosure that is:

(a) Attack-resistant (C&K Model # 2330-UAC)

(b) Secured with a key-lock and six (6) #6 X 1¼" sheet metal

screws.

removal from mounting surface.

(d) For safe and vault applications the control panel must be

monitored by a UL Listed shock sensor suitable for the

protection of sheet metal enclosures.

4. The Ademco Model AD10-12 bell with Model AB bell housing

must be used.

5. The power and tamper wiring between the bell and the control

panel must be completely enclosed in rigid conduit or electric

metallic tubing for a Grade A system or flexible conduit for a

Grade B system.

6. Zone(s) monitoring tamper circuitry must be 24 hour and non-

shuntable.

SYSTEM 238 Installation Manual

Earth Ground

To ensure the effectiveness of the lightning and transient protection

circuits, the control panel must be connected to "Earth Ground".

Ideally, this should be a common ground to the power lines, telephone

system, and security system. This type of ground, called a "Unified

Earth Ground", provides the best protection. The ground connection,

from a grounding rod, cold water pipe or other established ground

point, is made to the green jacketed wire providing a ground to the

panel housing. WIRING THE PANEL

Standby Battery

The SYSTEM 238 is designed to operate with a 12 volt, 6.5 Ah, sealed

lead-acid battery (C&K Model 1265). Do not use non-rechargeable

batteries or batteries other than sealed lead-acid.It is recommended

that you replace the standby battery every three to five years.

Connectthe redleadtothe batterypositiveterminal and theblacklead

to the battery negative. The battery is reverse-polarity protected by a

3 AG, 3 amp, fast-blow fuse (F4).

NOTE: If any fuse opens, remove AC and DC power, remove

the short oroverloadcondition, then replacethefuse

before restoring power. Do not substitute a higher

rated fuse.

Electromagnetic Interference

Vibratinghornscanproduceelectromagneticinterference(EMI).While

EMI will not damage the SYSTEM 238, it can cause transmission

errors and mis-dialing. To minimize EMI, install a 0.01 mfd, 100 volt

capacitor across the terminals of the horn. The capacitor must be

located in the horn.

AUXILIARYPOWER

The SW/AUX terminal provides positive 10 - 12.5 VDC

power for devices that require switched power for reset-

ting. Typical devices are glass-break and smoke detec-

tors.

The C terminal provides power common.

The AUXterminal supplies uninterrupted positive power.

Fuse F2

The SW/AUX and AUX terminals are protected by a 0.75 amp, 3 AG,

fast-blow fuse (F2).

The KEY+ terminal (red) provides 11 - 14 VDC keypad power.

The DATA terminal (green) is data from the keypad to the panel.

The C terminal (black) is common.

ARMING STATIONS

The CLK terminal (white) is the clock line.

Maximum wire length for connecting any keypad is 500' (152 m) of 22

AWG (0.643 mm) copper wire.

The SYSTEM 238 is capable of addressing up to 8 Alpha keypads.

LEDkeypadsdonotrequireaddressing.EachLEDkeypaduses35mA

of current. Each LCD keypad uses 64 mA of current. See Available

Power for current limitations. See page 4 for additional information on

keypad setup.

Terminal Labels:

SW/AUX, C & AUX

Terminal Labels:

C, KEY+, DATA, & CLK

LOOP INPUTS

Eachloopisindependently

configured through pro-

gramming. Loops can be

wired with an open circuit

switch, or closed circuit

switch,orwith a2.2Kohm

end-of-line(EOL)resistor.

When programmed as

EOL, either an open or a

short will be reported as

analarmifthesystemisin

an armed state.

N.O.

Alarm

N.C.

Alarm

EOL Loop

Terminal Labels: Z 1 - Z 8 & C

Fuse F3

TheKEY+terminalisprotectedbya0.75amp,3AG,fast-blowfuse(F3).

Terminal Label:

AC power is supplied by a 16.5 VAC, 25 - 40

VA transformer at 50 or 60 Hz. The transformer

mustbeaULlistedClass2transformer.Connect

the secondary of the transformer to the terminals labelled AC. Use

at least 18 AWG (1.02 mm) wire to reduce voltage drops. The

primary side of the transformer must be connected to an

unswitched receptacle. Do not connect primary to Ground-

Fault-Interrupt (GFI) circuits. Secure the transformer to the wall.

AC POWER

AC Power Failure

If an AC power failure lasts more than 15 minutes, the keypads will

display a system trouble. An AC failure report will be sent, if pro-

grammed. When AC is restored for five minutes, a restoral report will

be sent.

Precautions

Do not share the secondary of the transformer with other

devices. A foreign ground can damage the power supply,

voiding the warranty.

Do not use any transformer other than that specified in

the AC POWER section above.

Available Power

ThemaximumtotalpoweravailablefromtheAudible,AUX(Switched

and Unswitched), and Keypad is 800 mA. The switched auxiliary,

unswitched auxiliary, and keypads share the same power bus.

Combined power for these outputs should not exceed 500 mA**.

NOTE: The 50 mA switched power available on Loop 8 is

part of the total 500 mA AUX power.

** To comply with UL 365 and UL 609, this value must

be reduced to 150 mA.

Terminal Label:

BELL & C

AUDIBLE OUTPUT

The BELL terminal provides up to 1.3 amps at

10.5 - 13.5 VDC . The type of voltage (steady,

pulsed, chirp) and the time is programmable.

Fuse F1

TheBELL terminal isprotectedby a 2.5amps,3 AG fast-blowfuse(F1).

SYSTEM 238 Installation Manual

ALPHA KEYPAD INFORMATION

The Alpha keypad uses a top viewing display. This means the display

reads most clearly when viewed from a top angle rather than straight

on or from below. Mounting the keypad at the light switch level and

adjusting the viewing angle gives the best viewing results.

+When operated as a Super-

vised Loop, an open will be

reported as a Trouble.

Whetherthe systemisarmed

or disarmed. A short on a

Supervised Loop will be re-

ported as an alarm if the sys-

temisarmed,butwillhaveno

effect if the system is dis-

armed.

SupervisedLoop

N.C.

Trouble

N.O.

Alarm

Loop 8

Terminals C and Z8 are a standard loop that can also power 2-wire

devices. It supplies 10 - 12.5 VDC at 50 mA. Use Loop 8 to power 2-

wire glass-breaks and smoke detectors.

1. Position the tamper switch inside the cabinet at the lower right

corner of the cabinet. For the wall tamper, the plunger should go

through the small hole in the back of the cabinet. For the door

tamper,theplungershouldfaceoutfromthecabinet.Referto the

drawing below.

2. Connect the tamper switches in series and wire the tamper

terminals to a dedicated zone of the control panel.

3. Program the dedicated zone as desired: NC, EOL, 24-hour, etc.

Once the tamper switches are installed, opening the cabinet door or

removing the cabinet from the wall will result in a tamper signal at the

panel.

TAMPER SWITCH INSTALLATION

C&K has designed the SYSTEM 238 cabinet to use the Ademco

Model 19 tamper switch. The cabinet is constructed in order to

accommodate two switches. One tamper for the cover and a second

switch for a wall tamper. To install the tamper switches:

Tamper Switches installed in the SYSTEM 238 cabinet

LEAD-ACID

BATTERY

PRINTED CIRCUIT

BOARD

WALL

TAMPER SWITCH

DOOR

TAMPER SWITCH

TELEPHONE INTERFACE

ConnecttheSYSTEM238tothephonelineusing

the 9.X PCF cord (not included). The cord has an

8-pin telco plug on one end. Plug the telco end

directlyintothephonecompaniesRJ31orRJ38X

jack.ConnecttheflyingleadstotheSYSTEM238

PCB as outlined in the next column:

KEYPAD SETUP

Voltage Variations

Output voltages at terminals 5, 7, and 8 may vary between 9.0 and

14.4 VDC (worst case), depending on the load, battery condition, and

AC line voltage.

SYSTEM START-UP

Five minutes after the panel is powered up, it will dynamically test the

standby battery by interrupting AC power for two minutes and monitor-

ing the battery under load.

Standby Battery Time with One LED Keypad

AUX POWER DRAIN*

50 mA 32 hours

STANDBY TIME

* Total power for all keypads, auxiliary, and Loop 8

150 mA

250 mA

500 mA

24 hours

16 hours

10 hours

TB1

IfyoureplacethebatteryafteraSYSTEMTROUBLE-LOWBATTERY

message, you must test the battery under load conditions. Press [*] [6]

[4] [#] to start the Dynamic Battery Test.

NOTE: Some keypads may use [SHIFT] and [ENTER] in

place of the [*] and [#] keys, respectively.

RJ-38X Wiring

Diagram

Incoming

Telco Line

123

T1 = Seized Tip

R1 = Seized Ring

Red

Green

Protector

Ring

Tip

Tamper Jumper

House

Phones

9.X PCF

The 9.X PCF has eight flying leads. Wire them to the PCB terminals

as follows:

GRAY = ring seized

GREEN = tip

RED = ring BROWN = tip seized

BLUE and ORANGE = tamper

YELLOW and BLACK = not used

SYSTEM 238 Installation Manual

Adjusting the LCD Display

To adjust the viewing angle, remove the keypad from the back

mounting plate. Towards the bottom center of the circuit board is

a small hole. Insert a small screwdriver into the hole and adjust

R23, while holding the keypad at its mounting height. Adjust the

potentiometer as necessary for optimum viewing.

Addressing Keypads

Each Alpha keypad installed in the system must have an address.

Addresses must not be repeated. When replacing a keypad,

make sure the replacement keypad has the same address as the

previous keypad.

The first time you power up the system, unaddressed Alpha

keypads will display KEYPAD ADDRESS?. Press any number

from 0 through 7 at each keypad. The exact number you press is

not important as long as each keypad has a different address

number. The keypad will not accept values outside of the specified

range. Should you accidently use the same address for more than

one keypad, the system will fail to properly respond to the keypad

input. Refer to page 23 for assistance in correcting this problem.

Once all keypads have been addressed, reset the panel by

pressing [Master Combination] [*] [6] [8] [#] or by temporarily

removing both AC and DC power.

FACTORY SETTINGS

DEFAULT PROGRAM SETUP

The default programming of the SYSTEM 238 will allow you to

operateitas a localpanel withoutany additional programming.The

actual default programming values are shown on the Programming

Worksheet (last 2 pages of this manual).

Note: If you connect power before wiring the loops, install a

2.2K EOL resistor across each loops.

Combinations

Installer combination: 0 1 2 3 4 5

User #1 (Master) combination: 1 2 3 4

Users #2 - 8: disabled

Default installer combination: yes

Guest combination: no

Combination required: no

Arming type: goof-proof

Opening/Closing: disabled

Duress: disabled

Reporting

Account #1 and #2: disabled

Dialing type: pulse

RPS allowed: yes

Zones

Zone 1 = Entry/Exit delay - EOL circuit

Zone 2 = doors or windows - EOL circuit

Zone 3 = doors or windows - EOL circuit

Zone 4 = doors or windows - EOL circuit

Zone 5 = interior - EOL circuit

Zone 6 = interior - EOL circuit

Zone 7 = 24-hour panic or tamper - EOL circuit

Zone 8 = fire or smoke - supervised EOL circuit

Emergency soft zone: chirp audible

Fire soft zone: pulsed audible

Police soft zone: steady audible

Testing

Test report interval: 7 days and disabled

Timing

Entry time: 60 seconds and prewarn

Exit time: 30 seconds and prewarn

Bell time: 5 minutes

Unit Control

Local system: yes

Dynamic battery test: off

PROGRAMMING OPTIONS

ThefollowingisanalphabeticallistingofallSYSTEM238program-

ming options, including Command Locations and Digit Positions.

Digit Positions are inside parentheses ( ).

Option Location

Account #1 0C (1-6)

Account #2 10 (1-6)

Alarm Code by Loop 17 - 1E (1-2)

Alarm Loop Shunting by Loop 30 - 37 (2)

Alarm Receiver Select by Loop 1F - 26 (1)

Audible Time 2D (5)

Audible Type by Loop 1F - 26(5)

Bell Reverse Operation 2E (3)

Cancel Receiver Select 2A (6)

Cancel Report Code 2A (5)

Closing Report Code 2C (3)

Closing Report Receiver 2C (4)

Combination Command 09 (2)

Daily Battery Test Enable 2F (2)

Delay Before Dial by Loop 30 - 37 (4)

Delay Before Dial Time 0B (1)

Dial Attempts 0B (6)

Dial Type 0B (2)

Disable Loop LEDs 2E (5)

Door Chime Enable by Loop 30 - 37 (1)

Duress Report Code 2D (1)

Duress Report Receiver 2D (2)

Emergency Bell Type 27 (4)

Emergency Report Code 27 (1 - 2)

Emergency Receiver Select 27 (3)

Entry Delay Time 2D (3)

Entry Pre-alarm Enable 2E (1)

Exit Delay Time 2D (4)

Exit Pre-alarm Enable 2E (2)

Faulted Arming Type 09 (4)

Fire Bell Type 28 (4)

Fire Report Code 28 (1 - 2)

Fire Receiver Select 28 (3)

Four Minute Power Up Delay Enable 2F (3)

Group Shunt Enable 30 - 37 (3)

Guest Combination 08 (2 - 6)

Guest Combination Time 09 (1)

Installer Combination 00 (1 - 6)

Keypad RPS Enable 0B (3)

Local System Only 2F (1)

Loop Arming Type 1F - 26 (4)

Loop Audible Type 1F - 26 (5)

Loop Circuit Type 1F - 26 (6)

Loop Receiver Select 1F - 26 (1)

Loop Response Time 1F - 26 (2)

Loop Restore Type 1F - 26 (3)

Master Code (User #1) 01 (2 - 6)

Opening Report Code 2C (1)

Opening Report Receiver 2C (2)

Police Bell Type 29 (4)

Police Report Code 29 (1 - 2)

Police Receiver Select 29 (3)

Phone Ring Type 0B (5)

Receiver #1 Message Format 0A (2)

Receiver #1 Phone Number 0D - 0F (1 - 6)

Receiver #1 Receive Format 0A (1)

SYSTEM 238 Installation Manual

Option Location

Receiver #2 Message Format 0A (4)

Receiver #2 Phone Number 11 - 13 (1 - 6)

Receiver #2 Receive Format 0A (2)

Restoral Reporting Code by Loop 17 - 1E (3 - 4)

Restore Receiver Select 2A (2)

Ring Back Enable 2E (4)

RPS Enable 0B (4)

RPS Phone Number 14 - 16 (1 - 6)

Set Test Report Countdown Timer A0 (1)

Shunt Enable 30 - 37 (2)

Shunt Receiver Select 2A (1)

Shunt Reporting Code 17 - 1E (5 - 6)

Soft Zone Operation Enable 2F (4)

Test Report Code 2B (1 - 2)

Test Report Interval 2B (4)

Test Report Receiver Select 2B (3)

Unit Status Code 2A (3)

Unit Status Receiver 2A (4)

User Arming Type 01 - 08 (1)

User Combinations 01 - 08 (2 - 6)

can also scroll through the Command Locations in numerical order

by alternately pressing and releasing the [#] key.

To Exit Panel Programming

When you have finished programming, press [*] [#].

The panel will

also exit the programming mode if you do not press any key

within a five minute period.

PROGRAMMING CONVERSIONS

Hexadecimal Value Key Strokes

Data is programmed into the panel using the hexadecimal number

system, which consists of the digits 0 - 9 and the letters A - F. The

digits 0 - 9 are entered directly from the keypad. The chart below

shows how to enter the hexadecimal digits A through F.

132

45 6

789

Panel Programming Keys

You can program the SYSTEM 238 from the LED or Alpha keypad,

or remotely using the COMMANDER II software. Remote program-

ming information can be found in the COMMANDER II/MONITOR

II Operating Manual. This manual contains a brief description of

each programming option beginning on page 8.

PROGRAMMING THE PANEL

All panel wiring for the SYSTEM 238 should be completed prior to

applying power. You can only access the programming mode

when the control panel is disarmed.

NOTE: Command Location A0 must be addressed directly.

When programming this Command Location with an

Alpha keypad, the previously stored data is not dis-

played. To program this location, enter the Command

Location followed by the [#] key. Then enter the data

to be stored and again press the [#] key.

Warning: If you enter a Command Location and then press

the [#] key without entering any program data, the

keypad will beep 5 times, indicating an error. To

correct this problem, simply re-enter the Com-

mand Location and Data, then press the [#] key.

Programming with the LED Keypad

ProgrammingwithanLED keypad isaone-step process. Keyinthe

two-digit address (Command Location), followed immediately by

the desired programming values (program data), then press the [#]

key to store the data. The LED keypad does not display any

programmed values. If you are not sure that the correct program-

ming values have been entered, program the Command Location

again.

To Start Keypad Programming

Key in the [Installer Combination] [*] [0] [#]. The default Installer

Combination is 0 1 2 3 4 5. The programming mode is indicated by

the Program LED being lit on the LED keypad orCMD DATAbeing

displayed across the top row of the LCD display for the Alpha

keypad.

Programming with the Alpha Keypad

Enteringprogramdata withan Alpha keypadis atwo-step process.

First, key in the two-digit address (Command Location) to be

programmed and press the [#] key. The Alpha keypad displays the

Command Location and the data previously stored. Enter the new

data you wish to store and press the [#] key to write the data. You

Programming Hexadecimal Numbers

The Alpha keypad may be used to program the control panel. The

cursor is moved using the "E" and "P" keys, as indicated in the

figure below. The "F" key enters a blank space and moves the

cursor one position to the right.

NOTE: To program Command Location A0 with an LED

keypad, remember to enter the Command Location,

followed by the program data, then press the [#] key. ThesameprocedureisusedwithboththeLEDandtheAlphakeypads.

The last two Command Locations are CL 37 and CL A0. Pressing

the [#] key at these locations will advance you to CL 38 or CL A1,

respectively. Locations CL 38 and CL A1 are not used in the

SYSTEM 238. If you accidentally enter either of these locations,

press [*] [#] to exit programming, or enter the Command Location

number, followed by the [#] key, for the location you wish to

program.

SYSTEM 238 Installation Manual

PROGRAMMING the ALPHA KEYPAD

Keypad Message Programming

The Alpha keypad programming template is used to allow the in-

staller to program messages and zone descriptions into the Alpha

keypads. The template shown below should be used when pro-

gramming the keypad.

To activate the keypad programming mode, enter the [Installer's

Code] [*] [0] [1] [#]. Information may be entered into the keypad

in the form of letters (upper and lower case), numbers (0 - 9), and

22 special symbols. All characters are displayed in the order listed

above, i.e. upper and lower case letters, numbers, and special

symbols. The [Space] character precedes the letter A.

To enter a Message or Label, use the [2] key to scroll through the

characters until you reach the desired character. If you scroll past

the desired character, the [8] key may be used to scroll backwards.

When the desired character is displayed, press the [6] key to move

the cursor to the next character position. The [4] key moves the

cursor to the left. When all characters have been entered, press

the [#] key to write the message and move to the next message

position. Use the [0] key to move backward through the messages.

The message order is:

Ensure the Alpha keypad is wired to the SYSTEM 238 and power is

applied to the control panel.You can only access the programming

mode when the control panel is disarmed.

NOTE: Programming the Keypad is not the same as Keypad

Programming. 123

456

789

ALPHA II Programming Template

ALPHA PLUS Programming Template

12 3

654

78 9

NOTE: If you do not press any key for 5 minutes, the

keypadwill automaticallyexit theprogramming

mode.

To Exit Keypad Programming

When you have finished programming, press [*] [#].

The keypad

will also exit the programming mode if you do not press any

key within a five minute period.

The Alpha Keypad

You can program the Alpha keypads for special messages, each

of the 8 zone labels, and the keypad address.Zone Labels display

during the walk-test and when the [#] key is pressed during alarm

memory or faults. The programmable Service Message is dis-

playedduringACfailure,fuse failure, communication failure,orlow

battery. The Dealer Message displays when the system is dis-

armed. The keypad address is initially displayed only during

system start up (see page 5, Keypad Addressing).

These messages can be programmed directly from the Alpha

keypad or remotely using the Commander II/Monitor II software

package. For more detailed information about remote program-

ming, refer to the Commander II/Monitor II Operating Manual.

• SERVICE MESSAGE

• DEALER MESSAGE

• SOFT ZONE IDENTIFIERS (A, B, and C)

• HARDWIRED LOOP IDENTIFIERS

• KEYPAD ADDRESS

Both the Alpha (shown at the top of the next column) and the Alpha

Plus (shown below in the next column) use the same procedure to

program messages.

SYSTEM 238 Installation Manual

Command Locations 00 - 08

Command Location 00: Installer Combination

(1) (2) (3) (4) (5) (6)

012345

Default Values

Digit Position (1): First Digit of Installer Combination

Hard-coded to "0". Installer's combination will always start with 0.

Combination must have 5 digits in addition to Position (1).

Valid entries are 0 - 9.

Digit Positions (2) - (6): Remaining Digits in Combination

Command Location 01 - 08: User Arming Type and Combination

Digit Position (1): Arming Type

(1) (2) (3) (4) (5) (6)

91234E

10 1

**Default Values

01 = User #1 (Master)

02 = User #2

03 = User #3

04 = User #4

1 = Arm Only, No Closing (C) Report, No Shunting

2 = Disarm Only, No Opening (O) Report, No Shunting

3 = Arm and Disarm, No O/C Reports, No Shunting

05 = User #5

06 = User #6

07 = User #7

08 = User #8 (Guest)

4 = Arm Only, with Closing Report, No Shunting

5 = Disarm Only, with Opening Report, No Shunting

6 = Arm and Disarm, with O/C Reports, No Shunting

7 = Arm Only, No Closing Report, Shunting Allowed

8 = Disarm Only, No Opening Report, Shunting Allowed

9 = Arm and Disarm, No O/C Reports, Shunting Allowed

0 = Arm Only, with Closing Report, Shunting Allowed

1 = Disarm Only, with Opening Report, Shunting Allowed

2 = Arm and Disarm, with O/C Reports, Shunting Allowed

Digit Position (2): First Digit of Arming Code

Hard-coded to User's PIN. You cannot change this number.

Digit Positions (3) - (6): Remaining Digits in Combination

Comination may have from 1 - 4 digits in addition to Position (2).

Valid entries are 0 - 9.

**Default Values are different for

each user. Refer to the SYSTEM

238 Programming Worksheet at the

end of this manual for other user

default values.

PROGRAMMING CONVERSIONS

Hexadecimal Value Key Strokes

NOTE: Some programming locations allow variable-length data and require an

End-of-Number (EON) character. Program 4 ("E") after the last digit.

Fill remaining unused Positions with "0". The EON character is not required

if the last digit is in Position (6).

SYSTEM 238 Installation Manual

Command Locations 09 and 0A

Command Location 09: Arming/Combination Options

(1) (2) (3) (4)

0011

Default Values

Digit Position (2): Combination Command

0 = No

1 = Yes; requires combination for Bypass, Group Bypass, Instant Arm, keypad

activated RPS, and Test (central station and bell)

Digit Position (3): Default Installer Combination

0 = No; this enables the Pirate-GuardTM feature for added security

1 = Yes; combination changes back to factory value on power loss

Digit Position (4): Faulted Arming Type

1 = Goof-Proof: zones must be normal or shunted to arm

2 = Force Arm: faulted zones will be shunted at end of Exit Delay

3 = Chirp Alert: faulted delay zones will chirp bell during Exit Delay

Command Location 0A: Communications Formats

(1) (2) (3) (4)

1212

Default Values

Digit Position (1): Receiver #1 Receiver Format

Digit Position (2): Receiver #1 Message Format

1 = 3/1 single

2 = 3/1 extended 3 = 4/2 (2-digit reporting code)

4 = 4/1 5 = CFSK III

6 = 4/9 Ademco DTMF 7 = 4+2 SumCheck

5 = CFSK III

6 = DTMF, 1400 Hz

3 = SumCheck, 1400 Hz

4 = SumCheck, 2300 Hz

1 = Fast "A", 2300 Hz

2 = Slow "B", 1400 Hz

Digit Position (3): Receiver #2 Receiver Format

1 = Fast "A", 2300 Hz

2 = Slow "B", 1400 Hz 3 = SumCheck, 1400 Hz

4 = SumCheck, 2300 Hz 5 = CFSK III

6 = DTMF, 1400 Hz

Digit Position (4): Receiver #2 Message Format

3 = 4/2 (2-digit reporting code)

4 = 4/1

1 = 3/1 single

2 = 3/1 extended 5 = CFSK III

6 = 4/9 Ademco DTMF 7 = 4+2 SumCheck

(DTMF)

0 = Guest Time Disabled

1 = 1 day

2 = 2 days

3 = 3 days

4 = 4 days

5 = 5 days

6 = 6 days

7 = 7 days

8 = 8 days

9 = 9 days

Digit Position (1): Guest Combination Time

0 = 10 days

1 = 11 days

2 = 12 days

3 = 13 days

4 = 14 days

5 = 15 days

MessageFormat ReceiverFormat(s)

SumCheck (DTMF) DTMF, 1400 Hz only

CFSK III CFSK III only

Valid combinations of Receiver Format and Message Format are listed below.

3/1 Single or 3/1 Extended All formats, except CFSK III and DTMF, 1400 Hz

4/1 or 4/2 (2-digit reporting) Fast "A", 2300 Hz and Slow "B", 1400 Hz only

SYSTEM 238 Installation Manual

Command Locations 0B and 0C

Command Location 0B: Communications Control

Default Values

Digit Position (1): Delay Before Dial Time

0 = 0 secs

1 = 10 secs

2 = 20 secs

3 = 30 secs

311008

(1) (2) (3) (4) (5) (6)

4 = 40 secs

5 = 50 secs

6 = 60 secs

7 = 70 secs

8 = 80 secs

9 = 90 secs

0 = 100 secs

1 = 110 secs

2 = 120 secs

3 = 130 secs

4 = 140 secs

5 = 150 secs

Digit Position (2): Dial Type

Digit Position (3): Enable Keypad Activated RPS

0 = No

1 = Yes; allows remote programming to start from on-site keypad command

Digit Position (4): RPS Enable

0 = No

1 = Yes; allows remote programming to start from off-premise location

Digit Position (5): Phone Ring Type

0 = Single ring; uniformly timed rings with long pauses between rings

1 = Double ring; rings twice quickly followed by a long pause then rings twice again

Digit Position (6): Dialing Attempts

5 = 5 tries

6 = 6 tries

7 = 7 tries

8 = 8 tries

1 = 1 try

2 = 2 tries

3 = 3 tries

4 = 4 tries

9 = 9 tries

0 = 10 tries

1 = 11 tries

2 = 12 tries

3 = 13 tries

4 = 14 tries

5 = 15 tries

1 = DTMF - Touch Tone (10/sec) 2 = DTMF (5/sec) 3 = Pulse (10/sec)

Command Location 0C: Account Number 1

(1) (2) (3) (4) (5) (6)

000000

Default Values

Digit Positions (1) - (6): Account Number

Valid entries are 0 - F.

The Account Number is right justified. The last digit must be in Position (6).

The SYSTEM 238 will read the account number using:

Digit Positions (4) - (6) in 3-digit accounts

Digit Positions (3) - (6) in 4-digit accounts

Digit Positions (1) - (6) in 6-digit accounts

Fill all unused Digit Positions with 0's.

PROGRAMMING CONVERSIONS

Hexadecimal Value Key Strokes

Otros manuales para System 238

Tabla de contenidos

Otros manuales de Sistema de seguridad de C & K Systems

C & K Systems

C & K Systems System 236i Manual de usuario

C & K Systems

C & K Systems 236I3AU Manual de usuario

C & K Systems

C & K Systems SECURIT ST800L+ Manual de usuario

C & K Systems

C & K Systems Sierra S5030 Manual de usuario

C & K Systems

C & K Systems Securit 703 Manual de usuario

C & K Systems

C & K Systems Sierra Manual de usuario

C & K Systems

C & K Systems 236i/L Manual de usuario

C & K Systems

C & K Systems 236E Manual de usuario

C & K Systems

C & K Systems SpreadNet SN962-PENDANT Manual de usuario

C & K Systems

C & K Systems S5010 Guía

C & K Systems

C & K Systems Sierra Guía de referencia

C & K Systems

C & K Systems 236E Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario