BWI Eagle AIR-EAGLE XLT PLUS Manual de usuario

AIR-EAGLE XLT PLUS

461-HH-4

900 MHz RF Transmitter

Document Date: 11/11/2022

Product Rev: 11

461P-HH-4-003-CL

WARRANTY STATEMENT

BWI Eagle Inc. warrants the Air-Eagle Remote Control System, if properly used and installed, will be free

from defects in material and workmanship for a period of 1 year after date of purchase. Said warranty to

include the repair or replacement of defective equipment. This warranty does not cover damage due to

external causes, including accident, problems with electrical power, usage not in accordance with product

instructions, misuse, neglect, alteration, repair, improper installation, or improper testing. This limited

warranty, and any implied warranties that may exist under state law, apply only to the original purchaser of

the equipment, and last only for as long as such purchaser continues to own the equipment. This warranty

replaces all other warranties, express or implied including, but not limited to, the implied warranties or

merchantability and fitness for a particular purpose. BWI Eagle makes no express warranties beyond

those stated here. BWI disclaims without limitation, implied warranties of merchantability and fitness for a

particular purpose. Some jurisdictions do not allow the exclusion of implied warranties so this limitation

may not apply to you. To obtain warranty service, contact BWI Eagle for a return material authorization.

When returning equipment to BWI Eagle, the customer assumes the risk of damage or loss during

shipping and is responsible for the shipping costs incurred.

SIGNAL RANGE

Max range statements are estimates based on a clear line of sight with few interferences. Actual range will

vary based on transmitting power, orientation of transmitter and receiver, height of transmitting and

receiving antennas, weather conditions, electronic interference, terrain, and physical obstacles, including

but not limited to; walls, building structures, trees (foliage), metal objects, and landscape (hills, mountains).

WIRELESS STOP, ASTOP, and E-STOP SYSTEMS

Wireless E-STOP systems should never be considered a primary life-saving device.

At least one hard-wired switch must be available in the event the wireless system is

not operational. Failure to comply may result in serious injury or death to personnel

and damage to equipment.

Wireless STOP and ASTOP transmitters are not failsafe emergency stop controls.

They are NOT to be used as a life-saving device. They are designed for wireless

control of equipment or vehicle remote operation. Failure to use as intended may

result in serious injury or death to personnel and damage to equipment.

461P-HH-4-003-CL

INTRODUCTION

The Air-Eagle XLT Plus is an RF system designed for extra-long range wireless remote control of

electrical apparatus in a variety of industrial applications. Systems can consist of any number of receivers

and handheld or contact input transmitters working together to create an extra-long-range radio frequency

system that operates hazardous or hard-to-reach equipment from safe, convenient locations.

Eight user selectable frequencies allow multiple systems to be used in the same area without

interference.

This handheld transmitter is equipped to send four unique digital commands to an Air-Eagle XLT Plus

receiver located up to 5000 feet away. It will automatically go into “sleep” mode when not in use to

dramatically extend battery life. The Air-Eagle XLT Plus transmitter utilizes spread-spectrum technology

and provides the utmost in security and reliability.

INITIAL OPERATION SET-UP

This transmitter comes ready to operate, with batteries installed, and set to factory default settings. No

setup is necessary. To change frequency setting see FREQUENCY PROGRAMMING section.

APPROVALS

United States (FCC)

MCQ-XBPSX

Canada (IC)

1846A-XBPSX

Australia

RCM

Brazil

ANATEL: 05774-16-01209

461P-HH-4-003-CL

CONTROLS & INDICATORS

TX LED

LED illuminates continuously while button is pressed and unit is

transmitting. When this LED blinks briefly following a transmission, the

battery needs to be replaced. *

Pushbuttons 1-4

Transmits an individual RF code to the receiver.

*Note: The low battery notification signals have been improved to provide more noticeable

indications and to safely disable communications BEFORE a low battery condition can corrupt

internal memory causing device failure. When a low battery is first detected, the TX LED will blink

several times after all buttons are released. If it is possible to replace the batteries now, please do

so. If not, the operator has approximately 15 more button activations. During this time, when a

button is pressed and held, the TX LED will blink SLOWLY. The slow blinking will continue several

more times after all buttons are released. Transmissions are still being sent to the receiver during

this time. When a button is pressed and the TX LED is RAPIDLY blinking, the RF output is

disabled, and no signal will reach the receiver. The batteries MUST NOW BE REPLACED to

resume normal functions.

SPECIFICATIONS

Keypad

Durable Sealed Membrane Keypad –Eliminates Dust, Dirt and

Moisture Failures

Enclosure

ABS UL94 HB

Enclosure with ring is rated IP54 (Not

Waterproof)

Protective Ring

SEBS (TPE)

Power Requirements

3.0 VDC

Battery Type

(2) 1.5V lithium each, size AAA, to equal 3.0VDC nominal. For

best performance use only Energizer Brand Lithium Batteries. *

Battery Life (Active Usage)

Up to 3 months

Battery Life (Sleep Mode)

Up to 1 Year

Transmit Frequency

900MHz Spread Spectrum

RF Networks

Eight Independent Network Frequencies

RF Output Power

1 W

Max Transmit Range

Up to 5000 Feet

Operating Temperature

-40oF to +185oF

*Note: Current frequency setting is maintained in flash memory during battery replacement. No

reprogramming of frequency setting is necessary.

**Note: Max range statements are estimates based on a clear line of sight with few interferences.

Actual range will vary based on transmitting power, orientation of transmitter and receiver, height of

transmitting and receiving antennas, weather conditions, electronic interference, terrain, and

physical obstacles, including but not limited to; walls, building structures, trees (foliage), metal

objects, and landscape (hills, mountains).

461P-HH-4-003-CL

FREQUENCY PROGRAMMING

Read instructions completely before beginning programming procedure.

Transmitters are shipped from the factory set to Frequency 1 by default. The frequency can be changed

at any time by following the procedure below. Once changed, it is recommended to label the transmitter

with the selected frequency number.

*Note: Current frequency setting is maintained in flash memory during battery replacement. No

reprogramming of frequency setting is necessary after battery change.

To Check Current Frequency:

1. Press Buttons 3 & 4 simultaneously for approximately 4 seconds until the TX LED illuminates

RED.

2. Release all buttons. Watch while TX LED begins to blink.

3. The TX LED will blink RED one, two, three, or four times for frequencies 1, 2, 3, or 4, or will blink

GREEN one, two, three, or four times for frequencies 5, 6, 7, or 8. See table below for

clarification.

Operating Frequency:

TX LED Flashes

Frequency 1

1 RED flash

Frequency 2

2 RED flashes

Frequency 3

3 RED flashes

Frequency 4

4 RED flashes

Frequency 5

1 GREEN flash

Frequency 6

2 GREEN flashes

Frequency 7

3 GREEN flashes

Frequency 8

4 GREEN flashes

To Select Frequency 1 - 4:

1. Press Buttons 3 & 4 simultaneously for approximately 4 seconds until the TX LED illuminates

RED.

2. Release Buttons 3 & 4. While TX LED is still RED press Button 1 to select Frequency 1, Button 2

to select Frequency 2, etc.

3. The TX LED will blink to confirm the frequency selection has been accepted. It will blink RED

once to confirm Frequency 1, blink twice to confirm Frequency 2, etc.

Note - If the TX LED goes out before a frequency is selected, the setting will not change, and the

LED will blink corresponding to the current frequency setting. To change the frequency, start

again at step 1.

<< Continued >>

461P-HH-4-003-CL

FREQUENCY PROGRAMMING (Continued)

To Select Frequency 5 - 8:

1. Press Buttons 3 & 4 simultaneously for approximately 7 seconds until the TX LED illuminates

GREEN.

2. Release Buttons 3 & 4. While TX LED is still GREEN press Button 1 to select Frequency 5,

Button 2 to select Frequency 6, etc.

3. The TX LED will blink to confirm the frequency selection has been accepted. It will blink GREEN

once to confirm Frequency 5, blink twice to confirm Frequency 6, etc.

Note - If the TX LED goes out before a frequency is selected, the setting will not change, and the

LED will blink corresponding to the current frequency setting. To change the frequency, start

again at step 1.

Programming is now complete. Repeat the above procedure to change the frequency at any time.

DIMENSIONS

Otros manuales para AIR-EAGLE XLT PLUS

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Transmisor de BWI Eagle

BWI Eagle

BWI Eagle AIR-EAGLE FM2 43-1000-SSB-120VAC Manual

BWI Eagle

BWI Eagle AIR-EAGLE SR PLUS Manual de usuario

BWI Eagle

BWI Eagle 461-1200-DC Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR PLUS 36-1400-4B-DC Manual

BWI Eagle

BWI Eagle AIR-EAGLE XLT Manual

BWI Eagle

BWI Eagle AIR-EAGLE XLT Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR PLUS 36-HH-1 Manual de usuario

BWI Eagle

BWI Eagle 36-1400-DC Manual de usuario

BWI Eagle

BWI Eagle 36-1400-BAT Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE XLT 441-HH-9-VBR Manual

BWI Eagle

BWI Eagle AIR-EAGLE SR PLUS 36-1200-BAT Manual

BWI Eagle

BWI Eagle AIR-EAGLE XLT Manual

BWI Eagle

BWI Eagle AIR-EAGLE SR 38-1400-BAT Manual

BWI Eagle

BWI Eagle 441-10100-AC Manual

BWI Eagle

BWI Eagle AIR-EAGLE XLT Manual

BWI Eagle

BWI Eagle AIR-EAGLE FM2 43-1000-BAT Manual

BWI Eagle

BWI Eagle AIR-EAGLE FM2 43-1100 Manual

BWI Eagle

BWI Eagle AIR-EAGLE FM2 43-1100R2-DC Manual

BWI Eagle

BWI Eagle AIR-EAGLE XLT PLUS Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE XLT Manual

BWI Eagle

BWI Eagle AIR-EAGLE XLT 441UP-HHED-4-001 Manual

BWI Eagle

BWI Eagle AIR-EAGLE FM2 43-1000-SSB-R1/8-DC Manual

BWI Eagle

BWI Eagle AIR-EAGLE XLT Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR PLUS TX Manual

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario