Bushnell IMAGE VIEW 118322 Manual de usuario
Model#: 118322
Lit. #: 98-0916/07-10 Version 2.0
Instruction Manual
2
3
WARNING
Do NOT look directly at the sun through your binoculars.
Doing so may cause permanent eye damage.
NOTE: To reset the camera if you experience problems or if the display becomes
unresponsive, remove the batteries for at least one minute, then re-install them.
4
5
Congratulations on your purchase of the Bushnell ImageView®
binocular! The Bushnell ImageView binocular takes the
technology of digital photography and combines it with a high-
quality compact binocular. This allows you to observe sporting
events, wildlife, scenic vistas or anything you would normally use
a binocular for, and then save the image in a built-in attached
digital camera. You can then download these images to your
computer and e-mail them to your friends and family, print out
the picture, or save them in a photo album for future use. Before
using the product, please read the instructions contained in this
manual and take time to familiarize yourself with the different
parts and features of the product.
6
Camera and Binocular
Parts Guide Power/
MODE
Button
Camera
Lens
Binocular
Focus
SNAP
Button
Display
Tripod
Socket
Battery
Compartment
USB
Port
SD Card Slot
Power
LED
Remote
Jack
7
CAMERA PARTS
The camera is powered by two AAA alkaline, lithium, or NiMh batteries (not1.
included). Insert batteries into the compartment, with the springs in contact with
the negative (at) end of each battery. A power meter on the lower right of the
display indicates battery condition.
Insert an SD card ("upside down" with metal contacts facing up) in the slot if greater2.
storage is desired. You may use SD cards (not MMC cards) up to a maximum 32 GB
capacity. The camera has 16 MB of internal memory which can hold 30-40 photos
(depending on the selected resolution and other variables).
Press and hold the MODE button until the power LED comes on. The camera will3.
turn o automatically after about one minute if no buttons are pressed. Note:
when the camera is connected to a computer via the supplied USB cable, the camera
will draw power from the computer, with no battery drain.
Hold the ImageView steady and press SNAP to take a picture (or start/stop4.
shooting a video, when the camera is in video mode). The camera focus is preset
to take sharp photos at distances of about 35 feet or farther from the subject.
When using a tripod, you can help avoid the eects of camera shake by plugging5.
the supplied remote shutter release into the jack next to the SD card slot, and
using the button on the remote rather than SNAP to take photos.
Setup and Basic Operation
8
The ImageView will imprint the date and time in the bottom right corner of your photos.
To set the correct date and time, after turning on the camera, press and hold both the
MODE and SNAP buttons at the same time, until the display begins to ash. The display
now shows the last two digits of the year. Press the MODE button to move the cursor to
the second digit if necessary. Press the SNAP button to advance the digit to the current
year ("10" for 2010, etc). Then press MODE to go to the next number, which is the month.
Again, use SNAP to change this to the current month. Following the month display is:
date, hour (24hr format), and minute-continue to set these following the same process
using the MODE and then SNAP buttons. When you have completed all of the date/time
settings, the display will stop ashing and return to normal. Note that you will need to
reset the date/time after replacing batteries.
Your ImageView is already set to high resolution and quality right out of the box, and it
is not necessary to use the MODE settings and make any changes to get good results.
However, as you might want to shoot a video clip, delete one or more previous photos,
or explore other options, we recommend you review the available mode options listed
on the following pages. Briey pressing the MODE button will step through these
operational modes in the listed order, and you will see the icon for each mode along
with its current setting on the display. Use the SNAP button to select the desired setting
for any mode. If you make no changes, and the SNAP or MODE button is not pressed
within 5 seconds, the camera will return to normal operation and display.
Using the Operational Modes/Setting Date & Time
9
Mode Icon/Text Settings Description
Video Video
Camera
OFF, ON Select "ON" instead of "OFF" to put the camera in
video mode. Wait several seconds for the camera
to automatically return to the normal display, then
begin shooting by pressing SNAP. The counter
will show elapsed time. Press SNAP again to
stop shooting. The counter will advance by one,
indicating the video le has been saved. Return to
the video mode setting and select OFF to reset the
camera to still photo mode.
Quality Hq or Lq High, Low Select "Hi" (recommended) or "Lo" quality to choose
the amount of le compression, which aects the
size of the photo le. "Lo" allows more photos to be
stored in memory, but at reduced quality.
Resolution Hi or Lo High
(2.1megapixels),
Low
(VGA:640x480
pixels)
Select "Hi" (recommended) or "Lo" resolution, based
on your preference for better looking photos (Hi) or
being able to take a greater number of photos (Lo).
Using the Operational Modes (Bold indicates default settings)
10
Mode Icon/Text Settings Description
Line
Frequency
60 or 50 60 Hz, 50 Hz Set to match the AC power frequency (cycles) of
your country. This ensures that stills and videos shot
under uorescent lighting appear normal.
Continuous CT OFF, 3, 5 Select 3 or 5 frames to shoot a rapid series of photos
instead of a single frame when SNAP is pressed (in
normal still photo mode). To cancel, enter this mode
again and select OFF.
Memory
Access
MEM Sto (USB Mass
Storage), PC (USB
Camera)
Select "Sto" to access the internal or card memory
when the camera is connected to a computer with
the USB cable. "PC" allows the camera to be used as
a live USB/PC camera (note that the 8x magnication
and lack of close focus capability limits usefulness in
most size rooms)
Delete Last LSt+Trash
Can
None-press SNAP
to delete the last
photo or video
Select this mode and press SNAP to delete only the
last photo or video you took. The counter will go
down one number.
Using the Operational Modes (Bold indicates default settings)
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Prismáticos de Bushnell
Bushnell
Bushnell Image View 11-8200 Manual de usuario
Bushnell
Bushnell IMAGE VIEW 111024 Manual de usuario
Bushnell
Bushnell MARINE Binoculars Manual de usuario
Bushnell
Bushnell Night Vision 26-1554 Manual de usuario
Bushnell
Bushnell Spectator Manual de usuario
Bushnell
Bushnell Spectator Sport Series Manual de usuario
Bushnell
Bushnell ImageView 110833 Manual de usuario
Bushnell
Bushnell FUSION X Manual de usuario
Bushnell
Bushnell Night Vision 26-2036 Manual de usuario
Bushnell
Bushnell NIGHT WATCH 263230CL Manual de usuario
Bushnell
Bushnell ImageView 98-0917/04-09 Manual de usuario
Bushnell
Bushnell Image View 11-8321 Manual de usuario
Bushnell
Bushnell ELITE1500ARCTM 20-5101 Manual de usuario
Bushnell
Bushnell ImageView 11-1210 Manual de usuario
Bushnell
Bushnell Elite e2 Manual de usuario
Bushnell
Bushnell Instant Replay 18-0833 Manual de usuario
Bushnell
Bushnell LYNX 260401 Manual de usuario
Bushnell
Bushnell Night Vision 26-2640 Manual de usuario
Bushnell
Bushnell ImageView 11-8313 Manual de usuario
Bushnell
Bushnell Imageview 11-1025 Manual de usuario
