Burkert FreeLINE 8645 Diagrama de cableado
FreeLINE
Description for the replacement of modules within the valve
terminal
Beschreibung für den Austausch von Modulen innerhalb der
Ventilinsel
Description de l‘échange de modules dans îlot de vannes
We reserve the right to make technical changes without notice.
Technische Änderungen vorbehalten.
Sous resérve de modification techniques.
© 2008 Bürkert Werke GmbH & Co. KG
Operating Instructions 0811/00_EU-ML_00805841
Co n t e n t s
english
The supplementary instructions describe the extension of a valve terminal FreeLINE Type 8645. Keep these instruc-
tions in a location, which is easily accessible to every user, and make these instructions available to every new owner
of the device.
Please read the supplementary instructions thoroughly.
Follow the safety instructions!•
Failure to observe the warning may result in a fatal or serious injury.•
Failure to observe the warning may result in serious injuries or death. •
Failure to observe this warning may result in a medium or minor injury. •
Failure to observe the warning may result in damage to the device or the equipment. •
indicates important additional information, tips and recommendations which are important for your safety
and the flawless functioning of the device.
refers to information in these operating instructions or in other documentation.
designates a procedure which you must carry out.
→
english
If you are unsure, please contact your Bürkert Sales Center.
Contact address:
Bürkert Fluid Control System
Sales Center
Chr.-Bürkert-Str. 13-17
D-74653 Ingelfingen
Tel. + 49 (0) 7940 - 10 91 111
Fax + 49 (0) 7940 - 10 91 448
E-mail: [email protected]
Contact addresses can be found on the final pages of these operating instructions.
And also on the internet at:
www.buerkert.com Bürkert Company Locations
The operating instructions and data sheets for Type 8645 can be found on the Internet at:
www.burkert.com Documentation manuals / data sheets Type 8645
english
The supplementary instructions describe the replacement of modules within a valve terminal Type 8645 as well as
its extension by additional modules. Also follow the overall operating instructions and the Quickstart for handling
the complete device
There is a serious risk of injury when reaching into the equipment.
Turn off the pressure and release the pressure in the pipes before loosening pipes and valves!•
There is a serious risk of injury when reaching into the equipment.
Before starting work, always switch off the power supply and safeguard to prevent re-activation!•
Observe applicable accident prevention and safety regulations for electrical equipment!•
Improper assembly may result in injuries as well as damage to the device and the area around it.
This work may be carried out by authorised technicians only and with the appropriate tools!•
Hazardous situations may arise due to unintentional activation of the system.
Take appropriate measures to prevent the equipment from being unintentionally activated.•
The device contains electronic components, which react sensitively to electrostatic discharge (ESD). Contact
with electrostatically charged persons or objects is hazardous to these components. In the worst case scenario,
they will be destroyed immediately or will fail after start-up.
Observe the requirements in accordance with EN 100 015 – -1 to minimise or avoid the possibility of dam-•
age caused by sudden electrostatic discharge!
Also, ensure that you do not touch electronic components when the power supply voltage is present!•
english
1
To expand the FreeLINE valve terminal, first detach
the blue connecting bracket.
Using the two projecting lugs, pull up the blue
→
connecting bracket 1 and remove.
Attaching the connecting bracketFig. 1:
Pulling on one side may damage the locking bracket!
Using a screwdriver, release the 3 locking pins by
→
turning them through 90°.
In the released position the slots in the locking pins
are horizontal. The locking pins project over the
contact surface of the connecting bracket.
Release locking pinsFig. 2:
Supporting the snapping out of the locking pinsFig. 3:
By applying gentle lateral pressure to the exposed side areas of the valve terminal in the vicinity of the cor-
responding locking pins, they can be supported as they are snapped out.
english
By snapping out the three locking pins, the following
module is released and can be removed without
difficulty.
Releasing the following moduleFig. 4:
Remove the cover module parallel to the side.
→
The interface to expand the valve terminal is now
free.
Removing the cover moduleFig. 5:
If more modules are to be removed, repeat steps
→
1-3.
Ensure that an FE rail on the upper side of the ter-
minal is detached. Also the modules to be removed
must be detached from the wall or top hat rail.
Removing more modulesFig. 6:
english
Before adding new modules, first check that the
→
O-rings and seals are correctly positioned.
Then grease the O-rings and seals, both on
→
the pneumatic channels and on the electrical
connections.
Checking O-rings and sealsFig. 7:
Connect additional module to the valve terminal
→
by pushing it on parallel and pressing it into
position.
Ensure that the seals and plug-in contacts are not
damaged.
Attaching additional moduleFig. 8:
Connect added modules to the existing valve
→
terminal by pressing and then turning the three
locking through 90°.
The depression of the locking pins can be facili-
→
tated by pressing the module onto the existing
valve terminal. The slot is vertical.
Then attach the added modules to the wall or top
→
hat rail.
Securing added modulesFig. 9:
english
Push the blue locking bracket over the desig-
→
nated guides.
Ensure that the connecting bracket is inserted neatly
into the guides and is pushed down .
To do this, support the bracket by gripping both
→
lugs.
Attaching the connecting bracketFig. 10:
If more modules are to be added, repeat steps
→
5 – 8.
In doing so, note the appropriate system limits. To
close the valve terminal, attach the cover module
which fits the corresponding head module.
Attach cover module by pressing parallel on the
→
valve terminal.
Ensure that O-rings, seals and electrical interface are
not damaged.
Attaching more modulesFig. 11:
Lock locking pins according to Step 7 and push
→
down blue connecting bracket according to Step
8.
Re-attach FE rails.
→
Connect additional modules accordingly to the →
FE contact.
Attaching the connecting bracketFig. 12:
The valve terminal is ready for use again!
Valve terminal ready for useFig. 13:
english
Otros manuales para FreeLINE 8645
1
Tabla de contenidos
Idiomas:
Otros manuales de Terminal táctil de Burkert
