Bull NovaScale 9006 Manual de usuario
NovaScale 9006 Server
VGA Kit
Service Sheet
NOVASCALE
REFERENCE
86 A7 82FB 00
September 2009
The following copyright notice protects this book under Copyright laws which prohibit such actions as, but not
limited to, copying, distributing, modifying, and making derivative works.
Copyright ©Bull SAS 2009
Printed in France
Trademarks and Acknowledgements
We acknowledge the right of proprietors of trademarks mentioned in this manual.
All brand names and software and hardware product names are subject to trademark and/or patent protection.
Quoting of brand and product names is for information purposes only and does not represent trademark misuse.
The information in this document is subject to change without notice. Bull will not be liable for errors contained
herein, or for incidental or consequential damages in connection with the use of this material.
Servicing the VGA Kit 1
Servicing the VGA Kit
The VGA Kit is located on the Dummy CSI Interconnect Board (DSIB) (E) inside the server
drawer. This kit allows the connection of a VGA Cable to the DSIB board.
Figure 1. Locating the VGA kit
WARNING
This component is NOT hot-swappable.
Note This intervention is performed with the server drawer in the Servicing Position, as
explained below.
Required Tools
M3 Torx screwdriver
Estimated Intervention Time
30 minutes
2 Product Name - Manual Type
Procedure
1. Unpack the new component on a clean ESD-protected work surface.
2. Open the cabinet front door.
3. Power down the server drawer.
4. Open the cabinet rear door.
5. Disconnect the related cables (rear).
6. Place the Server Drawer in the Servicing Position.
1. From the rear of the cabinet, check that all cables connected to the server drawer are
clearly labeled at both ends. Label any cables that lack identification.
2. Extend the two red cable hanger stop pins and turn 90° to lock them into position.
Figure 2. Extending cable hanger stop pins
Servicing the VGA Kit 3
3. From the front of the cabinet, release the two captive screws securing the server drawer
to the cabinet rack (A).
Figure 3. Server drawer rack fixture screws
4. Slowly pull the server drawer forward until the rails are fully extended and locked, taking
care not to snag or loosen connected cables.
Figure 4. Server drawer in the servicing position
4 Product Name - Manual Type
7. Unlock/Open the Front Cover.
1. Press the 2 locking studs (A) on each side of the server drawer to unlock the front cover.
2. Raise the front cover to an angle of 45°.
Figure 5. Front cover raised
8. Remove the Front Cover.
Slide the raised front cover upward and remove it.
Figure 6. Removing the front cover
Servicing the VGA Kit 5
9. Remove the Rear Cover.
1. Slide the rear cover backwards.
Figure 7. Removing the rear cover
2. Lift up and away from the server drawer to remove it.
6 Product Name - Manual Type
10. Disconnect the Rear Right Cable Bundle.
mportant Check that all cables are correctly labeled before disconnecting.
The rear right cable bundle comprises the following cables:
•ILB-PDB 3.3V STBY Cable
•ILB-HDX Signal Cable
•PDB_ILB 12V Cable
•PDB_MTB 12V Cable
1. Remove the PCI separator, if required.
Figure 8. Removing the PCI separator
Servicing the VGA Kit 7
2. Disconnect the cables from the boards:
-PDB_ILB 12V Cable (A) from the ILB
-ILB-PDB 3.3V STBY Cable (B) from the ILB
-ILB-HDX Signal Cable (C) from the ILB
-PDB_MTB 12V Cable (D) from the MTB
Figure 9. Disconnecting the rear right cables
3. Place the cables outside the server drawer. If necessary, free the cables by unclipping the
cable straps.
8 Product Name - Manual Type
11. Disconnect the Rear Left Cable Bundle.
mportant Check that all cables are correctly labeled before disconnecting.
The rear left cable bundle comprises the following cables:
•PDB_MTB 12V Cable
•ILB-PDB 3.3V STBY Cable
•LCP-ILB Mixed Cable
•ILB-HDX Signal Cable
•2 x ILB-HDX SATA Cable
1. Remove the PCI separator, if required.
Figure 10. Removing the PCI separator
Otros manuales para NovaScale 9006
1
Tabla de contenidos
Otros manuales de Servidor de Bull
Bull
Bull Novascale T810E1 Manual de usuario
Bull
Bull NovaScale T840 E2 Manual de usuario
Bull
Bull Novascale R423-E2 Manual de usuario
Bull
Bull DPS 7000 Manual de usuario
Bull
Bull Escala E1-700 Manual
Bull
Bull NovaScale Blade B260+ Manual de usuario
Bull
Bull NovaScale 5xx5 Manual de usuario
Bull
Bull novascale R480 F2 Manual de usuario
Bull
Bull NovaScale R440 F2 Manual de usuario
Bull
Bull NovaScale T860 E1 Manual de usuario
Bull
Bull Escala Power5 Series Manual del propietario
Bull
Bull Escala Power6 Manual de usuario
Bull
Bull NovaScale T860 F2 Manual de usuario
Bull
Bull NovaScale T840 F3 Manual de usuario
Bull
Bull NovaScale Blade 2040 Series Manual de usuario
Bull
Bull Escala Power7 Series Instrucciones de operación
Bull
Bull NovaScale R460 E1 Manual de usuario
Bull
Bull Escala Power7 Series Manual de usuario
Bull
Bull Escala Power7 Series Manual
Bull
Bull Escala EL260B Manual de usuario
