Building 36 B36-T10 Manual de usuario

Intelligent Thermostat

User Guide

2 | Intelligent Thermostat User Guide Intelligent Thermostat User Guide | 3

Thermostat Backplate Trim Plate (Optional)

• Before installing or servicing

your thermostat, turn o

power to the system at

circuit breaker.

• Leave power o until

nished installing or

servicing.

• Shorting the electric

terminals at the control

on the heating or cooling

system may damage the

thermostat. Do not test the

system this way.

• You must follow all local

codes and ordinances for

wiring your system.

• This thermostat should only

be powered by 4AA alkaline

batteries or a Listed class

2 power supply at 24 VAC

(C-Wire or wall transformer).

• An amperage higher than 1

amp to each thermostat

relay load may cause

damage to the thermostat.

• To avoid electrical shock

and to prevent damage

to the HVAC system and

thermostat, disconnect

the power supply before

installing or servicing. It is

recommended this be done

at the circuit breaker.

Drywall Screws (3) AA Batteries (4) Drywall Anchors (3)

• Needlenose Pliers • Phillips Screwdriver • Power Drill • Pencil

Contents:

Recommended Tools:

4 | Intelligent Thermostat User Guide Intelligent Thermostat User Guide | 5

Operation

Display

• Press any button to wake the thermostat up.

• After waking, the display will show the current

mode and room temperature.

• IF the system is running the display will

wave up for heating or down for cooling.

• Press the up or down button once to change to

display current setpoint.

• The currently illuminated MODE icon will

being to pulse.

• Press the up or down button again to adjust the

setpoint.

• Press the mode button at any time to change

the mode.

• The modes are HEAT, COOL, AUTO, and OFF.

• The thermostat will display the mode

appropriate setpoint.

• In AUTO, the brighter icon will indicate which

setpoint is currently displayed and active (HEAT

or COOL).

• After 5 seconds the display will return to

the current room temperature. The MODE

icon will become solid to indicate this. After 5

more seconds the display will turn o and the

thermostat will sleep.

Buttons

1. UP Button – Adjust target temperature up.

2. MODE Button – Change thermostat from

HEAT, COOL, AUTO, and OFF modes.

3. DOWN Button – Adjust target temperature/

(un)Pair to and from network.

Icons

4. HEAT Icon – Illuminated in HEAT or AUTO

mode.

5. COOL Icon – Illuminated in COOL or AUTO

mode.

6 | Intelligent Thermostat User Guide Intelligent Thermostat User Guide | 7

Location: Removing Existing Thermostat:

If replacing an old thermostat,

the new thermostat will be

mounted in place of the old.

If a new location is desired

it will be necessary to move

your wiring.

New installations and

relocation should follow

the guidelines below

to ensure the most accurate

temperature reading and ease

of use.

• Mount thermostat on an

inside wall, approximately 5

ft. (1.5m) above the oor in a

frequently used room.

• Do not install in locations

near appliances or

devices that aect the

local temperature such as

televisions, lamps, or dryers.

• Avoid areas that are exposed

large temperature variances,

such as: direct sunlight, near

an AC unit, above or below

auxiliary heat and air vents,

and drafts from windows.

• Be aware of what is on the

other side of the wall the

thermostat is being installed

on. Do not install on walls

adjacent to unheated rooms,

stoves, or housing hot water

pipes.

• Damp areas will not only

aect the humidity reading

of your thermostat, but could

lead to corrosion shortening

the life of your thermostat.

• Install in a location with good

air circulation. Stagnant air

will not accurately reect the

rate of change of temperature

in the room. Avoid areas

behind open doors, corners,

and alcoves.

• Wait until construction and

painting are nished before

installing.

Test your system

Verify that your heating and/

or cooling system is operating

properly before you try to

install your new thermostat.

DO NOT do so by shorting

(jumper) across electric

terminals at the furnace or air

conditioner. This may damage

the thermostat.

DO NOT REMOVE your

existing thermostat until

power has been turned o

at the circuit breaker.

Once power to the heating AND cooling systems is o follow these

steps:

• Remove cover from your existing thermostat. Do not disconnect

the wires yet.

TIP: Take a picture of the wires before you detach them from the

existing thermostat.

• Label all existing wires, one at a time, with the labels provided.

8 | Intelligent Thermostat User Guide Intelligent Thermostat User Guide | 9

Install Your New ThermostatRemoving Existing Thermostat:

• Disconnect all of the wires and remove the

existing thermostat.

TIP: Remember to secure the wires so they don’t

fall into the wall.

CAUTION: Wiring can vary for each

manufacturer. Label all wiring before removing

it from your existing thermostat.

What wires does your system use?

Make sure your wires are labeled correctly. It may

be necessary to nd the ‘other end’connection

for each wire on your heating or air conditioning

equipment and read the label there.

IMPORTANT: This thermostat runs on batteries

and the C wire. If you do not have a C wire you

can run a new wire from the HVAC or use a

standard 24VAC wall transformer

Prepare the wires

Please follow these guidelines for safe and

secure wire connections:

• Ensure the wires are a proper gauge.

• Make sure wires have exposed straight ends

about 1/8”long.

CAUTION: Verify that your system is 24 VAC. If

your old system is labeled as 120 or 240 volts, or

has wire nuts your system is high voltage. Do not

install your thermostat to a high voltage system.

Contact your local HVAC professional for help.

Install the back plate

Use the bubble level provided

on the back plate as a guide.

Mark where the screws will

go with a pencil through the

screw holes on the back plate.

TIPS:

• Use the trim plate to cover

up any marks or holes left

from the old thermostat.

Attach the trim plate before

securing the back plate to

the wall.

• Drill holes with 3/16”drill bit

to tap in the drywall anchors

for added support.

Wire your new thermostat

Go to page 8 to nd the wiring diagram that matches your wiring

and insert the wires into the back plate.

TIP: Anything that wasn’t connected to your old thermostat

shouldn’t be connected to your new thermostat either.You may

also have extra wires that do not match. Leave them as is.

EXCEPTIONS:

• If you have R, connect it to RH.

• If you have RH & RC remove black jumper in lower left corner of

back plate terminal board.

• Z can be used for W3, H, or DH.

10 | Intelligent Thermostat User Guide Intelligent Thermostat User Guide | 11

Wiring Diagrams:

Conguration 1

RH, W

Conguration 2

RH, W, G

Conguration 5

RH, G, W, W2, Y, Y2

Conguration 6

RH, G, OB, Y

Conguration 3

RH, W, Y, G

Conguration 4

RH, RC, G, W, Y

Conguration 7

RH, G, W, W2, Y, Y2, OB

12 | Intelligent Thermostat User Guide Intelligent Thermostat User Guide | 13

Insert batteries into Thermostat body Connect the Thermostat to the Gateway

The thermostat can be powered by battery or 24

VAC. If a wall transformer is used to power your

thermostat connect between C and RH.

Ensure the batteries are installed following the

specied polarity markings on the thermostat.

CAUTION: Special Battery Warning

• Always replace the batteries as soon as Low

Battery is indicated. If the batteries die, your

thermostat could leave the HVAC system on,

overheating or freezing your home.

• Always replace the batteries at least once a year.

This will protect your thermostat from damage

and corrosion by leaking batteries.

• If your home is unoccupied for a month or more,

such as vacation homes, you should replace

the batteries as a preventive measure against

battery failure while you are away.

• Use only new batteries when changing.

• Bring Gateway to the Thermostat.

• Put the thermostat in OFF mode (No mode icons are lit).

• Press the inclusion button on the Gateway.

• Press and hold the DOWN button the thermostat to begin pairing. The RADIO icon should start

blinking.

• When the RADIO icon becomes solid, the thermostat is joined to the network.

• Login to your account to sync your thermostat with the Building 36 system, or contact your local

professional for installation setup.

14 | Intelligent Thermostat User Guide Intelligent Thermostat User Guide | 15

Install Thermostat body to back plate

Press the thermostat body rmly into the back

plate mounted to the wall. Ensure that the

pins on the body are correctly aligned with the

header attached to the terminal board on the

back plate. Failure to do so could cause damage

to the thermostat.

Turn the power on

Restore power to your heating and cooling

system. This can be done at the circuit breaker.

Congure Your System Check Your System

Your thermostat conguration will be done

online at the customer site on your customer

account page. Here you will congure the

parameters of your system, such as: Heat

Pump or Normal, number of heat and cool

stages, heating fuel, calibration temperature,

and congurable terminal (Z). Refer to your

conguration number on the wiring diagrams

page to see the values you should enter on the

online conguration.

This is also were you have the option to change

advanced conguration settings, such as: Swing,

Dierential, Recovery Setting, Fan Circulation

Period and Duty Cycle, Maximum Setpoints,

Minimum Setpoints, Thermostat Lock, Demand

Response Delay, Demand Response Duty Cycle,

and Modes Enabled.

WARNING: Use caution when changing

advanced conguration settings. These

conguration settings should only be changed

by those familiar with heating and cooling

systems’parameters. Contact your local HVAC

professional for help.

For denitions of these settings and more

information go to www.building36.com

By default the thermostat is congured to 2 heat

stages and 2 cool stages (2 Heat Pump, 2 Aux).

To check heating

Press the MODE button to select HEAT mode.

• Press UP button to raise setpoint above room

temperature.

• Wait 10 seconds for system to turn on.

• After verify the heating system is working,

raise the setpoint to the desired temperature.

To check cooling

Press MODE button to select COOL mode.

• Press DOWN button to lower setpoint below

room temperature.

• Wait 10 seconds for system to turn on.

• After verify cooling system is working, lower the

setpoint to the desired temperature.

16 | Intelligent Thermostat User Guide Intelligent Thermostat User Guide | 17

Troubleshooting

Batteries die quickly

If a thermostat is paired using a C-Wire, that

information is saved in the network and cannot

be changed unless removed and paired again

without a C-Wire connected. The same applies

for inclusions on battery power. If you nd your

thermostat batteries are dying unusually quick,

check and make sure the C-Wire connection

is still intact. If a device is paired using C-Wire

the Z-Wave communication never sleeps and

the thermostat will act a repeater, sending

messages for other devices as well. If the C-Wire

is removed this kind of activity will drain the

battery very quickly.

Manual conguration of HVAC system on

thermostat

The system type (Normal or Heat Pump) can be

physically set on the thermostat if necessary by

doing the following:

1. Put thermostat in OFF mode.

2. Press and hold the UP button.

3. Press UP or DOWN buttons to select either

‘HP’ for heat pump conguration or‘NORM’for

normal conguration.

4. Press MODE button to conrm your selection.

Exclusion of thermostat from Z-Wave

network

If for some reason the thermostat must be

removed from the network, follow the steps

below to do so.

1. Press and hold the exclusion button on the

gateway.

2. Press and hold the DOWN button the

thermostat to enter exclusion mode. The

RADIO icon will begin ashing red.

3. When the RADIO icon becomes solid the

thermostat has now been successfully

removed from the network.

Heat pump is cooling when it should be

heating

Because both types of heat pump reversing

valves share a single terminal on your thermostat

back plate, you need to be sure you have the

thermostat congured for the correct wire. Try

switching your O/B selection on the customer

thermostat conguration page. Contact your

local HVAC professional for further with this issue.

The same applies to a heat pump that is heating

when it should be cooling.

Heating or cooling doesn’t turn on when the

target is set above or below the ambient

The thermostat is congured to have a minimum

setting of a half degree dierence in temperature

from the target before the system turns on

to protect the system from damage due to

excessive use. The cooling system also has a built

in compressor delay. Each time compressor is

turned on, a large amount of pressure is built up

and must be equalized. This delay time prevents

damage to the compressor from not allowing

this pressure to equalize before being turned

on again. For more help contact your local HVAC professional or Building 36 Technologies.

18 | Intelligent Thermostat User Guide Intelligent Thermostat User Guide | 19

Notices

FCC NOTICE:

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful interference.

AND

2. This device must accept any interference

received, including Interference that may cause

undesired operation.

This equipment has been tested and found

to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference

to radio communications. However, there is

no guarantee that interference will not occur

in a particular installation. If this equipment

does cause harmful interference to radio or

television reception, which can be determined

by turning the equipment o and on, the user

is encouraged to try to correct the interference

by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment

and receiver. Connect the equipment into an

outlet on a circuit dierent from that to which

the receiver is connected. Consult the dealer or

an experienced radio/TV technician for help.

NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY

APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID

THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

Under Industry Canada regulations, this radio

transmitter may only operate using an antenna

of a type and maximum (or lesser) gain approved

for the transmitter by Industry Canada. To reduce

potential radio interference to other users, the

antenna type and its gain should be so chosen

that the equivalent isotropically radiated power

(e.i.r.p.) is not more than that necessary for

successful communication.

Conformément à la réglementation d’Industrie

Canada, le présent émetteur radio peut fonctionner

avec une antenne d’un type et d’un gain maximal

(ou inférieur) approuvé pour l’émetteur par

Industrie Canada. Dans le but de réduire les risques

de brouillage radioélectrique à l’intention des

autres utilisateurs, il faut choisir le type d’antenne

et son gain de sorte que la puissance isotrope

rayonnée équivalente (p.i.r.e.) ne dépasse pas

l’intensité nécessaire à l’établissement d’une

communication satisfaisante.

Tabla de contenidos

Otros manuales de Termostato de Building 36

Building 36

Building 36 Intelligent Thermostat Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario