Brother GT-541 Hoja de especificaciones
GGT
T-
-5
54
41
1
M
MA
AI
IN
NT
TE
EN
NA
AN
NC
CE
E
C
CL
LE
EA
AN
NI
IN
NG
G
Maintaining GT541 Head Cap Rubbers and Wiper
Keeping the Rubber Caps and Wiper on your machine clean is the most important part of maintaining your
GT541. The caps and wiper are constantly being used throughout initial power up and during every auto
clean and operation of the machine. Although the rubber caps and Wiper are designed for use in an
industrial environment, they need to be inspected after every Ink Cartridge/Wiper Cleaner change and
cleaning. After prolonged use, the wiper and caps may become damaged and or worn. Lack of cleaning
will cause excess ink to build up on the caps and wiper. With infrequent use, the buildup of ink on the caps
and wiper will become dry and gooey. When the machine is powered on, this dry gooey ink will be wiped
against the underside of the print heads, likely clogging the nozzles. Cleaning should be done every time a
cartridge is changed, or if the machine is to sit unused for more than 3 days. If the machine is going to sit
idle for more than one week, please contact Brother Technical Support (1-877-427-6843), for long-term
storage instructions. The following steps will explain proper cleaning of wiper and caps.
Step 1: Entering maintenance mode and cap wiper clean menu.
Cleaning the Print Head Cap and Wiper Blade
Always clean the Print Head Caps and Wiper Blade when replacing the Wiper Cleaner. A new Wiper
Cleaner is enclosed in the box of a new BLACK Ink Cartridge, and it needs to be replaced when the
BLACK Ink Cartridge is changed (or with the most frequently changed ink color cartridge).
(1) Turn on GT-541 if it is off.
(2) Press the OK Button to open the Menu Display.
(3) Press the Up/Down Button to select the “Maintenance”, and then press the OK Button.
(4) Press the Up/Down Button to select the “Cap/Wiper Clean”, and then press the OK Button. The
following message appears.
(5) Turn off GT-541.
(6) Open the Front Cover by unlocking the Cover Locks.
(7) Pull out the Wiper Cleaner Cassette.
<Note>
•Do not tilt the Wiper Cleaner Cassette; ink may get on your hands or clothing.
•Do not touch the Clearance Sensor (the bar above the Wiper Cleaner Cassette); it may cause a
malfunction.
Replacing the Wiper Cleaner
(8) If the ink inside of the Wiper Cleaner Cassette is soiled with ink:
Wear gloves and remove the ink with a dry cloth, and then clean with a cloth damped with water.
(9) Push both sides of the Wiper Cleaner Cassette to open it.
(10) Carefully drop off the used Wiper Cleaner in a trash can/bag by turning it upside down.
<Note>
Dispose the used Wiper Cleaner in compliance with your local regulations.
(11) Insert the two projections of the Wiper Cleaner Cassette into the holes on the new Wiper Cleaner.
(12) Close the Wiper Cleaner Cassette.
Make sure that the bottom of the Wiper Cleaner is set within the two projections on the Wiper Cleaner
Cassette.
Cleaning the Print Head Cap and Wiper Blade
(13) Open the Cap Cleaning Kit. It comes with the new Black Ink Cartridge.
The following items are included. Or can be purchased separately PN: SA5774-001.
(14) Wear the gloves, and wet both sides of a Clean Applicator with the Wash Liquid. <Note>
Use only the Wash Liquid included to wet the Clean Applicators; using other liquid will cause damage to
the Print Heads and Rubber caps.
(15) Use the one side of wet Clean Applicator to clean the front side of the Wiper Blade.
When cleaning back side of Wiper do not
apply excess pressure but slightly swabbing
and wiping gently. Excess pressure can
remove rubber from holder.
(16) Use the other side of the wet Clean Applicator to clean the backside of the Wiper Blade.
When cleaning back side of Wiper do not
apply excess pressure but slightly swabbing
and wiping gently. Excess pressure can
remove rubber from holder.
(17) Wet other two Clean Applicators and use them to remove ink or dust from the Print Head Caps. Use
one side of the Clean Applicator to clean one Print Head Cap.
<Note> Do not use the dry Clean Applicator; it cannot clean ink or dust. It may damage the Print Head
Caps.
(18) Insert the Wiper Cleaner Cassette straight into GT-541.
<Note> Do not touch the Clearance Sensor (the bar above the Wiper Cleaner Cassette); it may cause a
malfunction.
(19) Close the Front Cover, and then turn on GT-541. If GT-541 turns on without any problem,
replacement of the Wiper Cleaner Cassette has been completed. If there is problem (abnormal noise or
error,) turn off GT-541 and check if the Wiper Cleaner and the Wiper Cleaner Cassette are correctly
installed.
Print and check the Nozzle Check Pattern.
You can identify which Print Head has the problem if any by checking the Nozzle Check Pattern.
(1) Install the Platen 14 x 16.
(2) Set the Platen height to the “A” position.
(3) Place a paper (A4 or letter size) on the Platen as shown below. You can use a T-shirt instead
of the paper.
(4) Press the OK Button to open the Menu Display.
(5) Press the Up/Down Button to select “Test Print”, and then press the OK Button.
(6) Press the Up/Down Button to select “Nozzle Check”, and then press the OK Button.
The following message appears.
(7) Press the OK Button to start printing the Nozzle Check Pattern.
(8) Check the printed pattern to identify which Print Head has the problem if any.
If there is stripes (arrow 1) or line breaks (arrow 2), the Print Head of the color (in the following
example: Black) has the problem. The Print Head need to be cleaned or simply do a power clean
on that head to see if that resolves the missing nozzle or stripe.
1. Performing a powerful Head cleaning.
(9) Press the Platen Button to eject the Platen.
Press the OK Button to open the Menu Display.
(10) Press the Up/Down Button to select “Head Cleaning”, and then press the OK Button.
(11) Press the Up/Down Button to select “Powerful Clean” Cleaning mode, and then press the OK
Button.
(12) Press the Up/Down Button to select the color to do cleaning on, and then press the OK
Button.
The following message appears, and the Powerful cleaning starts.
The display returns to the Print Head color-selecting display, when the powerful cleaning has
been completed.
(13) Print and check the Nozzle Check Pattern again as step 8 shows on previous page and
missing nozzle should be resolved. If problems resume contact Brother Support
(877)4BROTHER.
2. Head Cleaning.
For head cleaning instructions, refer to your CD/DVD that was shipped with your machine or visit
the owner’s site online at: https://www.brother-usa.com/GarmentPrinters/OwnerLogin.aspx to
view video instructions.
Install CD On line Owner Log In
Otros manuales para GT-541
9
Tabla de contenidos
Otros manuales de Impresora de Brother
Brother
Brother HL-1230 Manual de usuario
Brother
Brother GT Manual de usuario
Brother
Brother HL-5030 Manual de usuario
Brother
Brother RJ-3150 Manual de usuario
Brother
Brother HL-4140CN Manual de usuario
Brother
Brother HL-1260 Manual de usuario
Brother
Brother DSMobile 920DW Manual de usuario
Brother
Brother HL-600 Series Manual de usuario
Brother
Brother DCP-1518 Manual de usuario
Brother
Brother MFC-J2340DW Manual de usuario
Brother
Brother DCP-7055 Manual de operación y mantenimiento
Brother
Brother ep44 Manual de usuario
Brother
Brother HL-B2080DW Manual técnico
Brother
Brother HL-5030 Manual de usuario
Brother
Brother DCP-J525W Manual de operación y mantenimiento
Brother
Brother TN3030 Manual de usuario
Brother
Brother MFC-J680DW Manual de operación y mantenimiento
Brother
Brother HL-1110 Manual de usuario
Brother
Brother RuggedJet RJ-2030 Manual de funcionamiento
Brother
Brother GT-3 Series Manual de funcionamiento
