Britpart DA4512 Manual de usuario
2
Ty r e P r e s s u r e M o i t o r i g S y s t e m
Co te ts
Thank you choosing the Britpart Tyre Pressure Monitoring System.
This system is an advanced monitoring & a ert system of tyre conditions. It monitors tyre pressure and temperature and re ays the
state of each tyre to a disp ay unit. When any abnorma ities are detected, the system wi disp ay the status of the affected tyre and
sound an a arm to ensure you take action to remedy the prob em. Keeping your tyres in good condition at the right pressure can
extend the ife of your tyres and reduce fue consumption.
P ease read this manua carefu y before using our product.
Index
Notification 4
Genera Insta ation Diagram 4
Working Princip e 5
Components 5
Technica Specifications 6
Insta ation
Sensor Insta ation 7
Disp ay and Receiver Insta ation 8
Operation
System Operation 9
System A arm 10
Function Setting
Interface Setting 11
Temperature Unit Setting 12
Pressure Unit Setting 13
Set Reference Pressure 14
ID Exchange 15
Learn New ID 16
Learn ID By Low Frequency 17
Appendix 18
3
This system app ies to 4 whee ed vehic es with meridian tyre (vacuum tyre) and co d tyre pressure (22ºC) ower than 2.8 bar
(280KPa/40.6psi/2.86*104kgf/m2). It shou d be insta ed by a qua ified professiona according to this manua . This system is an
e ectronic device that measures and disp ays the inside air pressure and temperature of the tyres and gives a warning signa when
an abnorma ity is detected. The system has no contro ing function so the driver shou d rectify and detected prob ems as soon as
possib e. The performance of the sensors cou d be affected by chemica materia s. Preset pressure from the manufacturer is 2.40
Bar (240KPa/34.8psi/2.45*104kgf/m2). P ease set it to your vehic es recommended pressures after the initia insta ation (see
detai s on page 14). This system is to be used as a monitoring aid on y and Britpart wi take no responsibi ity after the kit is insta ed
and the user must ensure tyres are inf ated to the vehic e manufacturers recommendations.
Notificatio
Ge eral I stallatio Diagram
No. 2 Tyre Sensor No. 3 Tyre Sensor
No. 1 Tyre Sensor No. 4 Tyre Sensor
Disp ay
Receiver
B ack wire to ground
White wire to ACC ON
Red wire to +12v power
4
This system consists of 4 sensors and LCD disp ay. The sensor monitors the tyre inner pressure and temperature then transmits
the signa , the disp ay unit wi then show the signa and give an a arm if appropriate.
Worki g Pri ciple
Compo e ts
Ty r e P r e s s u r e M o i t o r i g S y s t e m 5
1234567
Code Name of Compo e t Qua tity
1Disp ay 1
2Receiver 1
3Tyre Sensor 4
4Disp ay Bracket - 1 2
5Disp ay Bracket - 2 1
63M Sticker 2
7Instruction Manua 1
Tech ical Specificatio s
6
Tyre Se sor
Worki g Voltage Ra ge DC 2.1 – 3.6v - High-powered battery inside
Worki g Curre t 0.6uA - Standby / 9mA - Transmission status
Worki g Temperature Ra ge -40–125ºC
Tra smitti g Freque cy 433.92MHz
Tra smitti g Power >5dBm
Modulati g Method FSK
Measurable Pressure 0–3.5bar (0–350KPa/0–50.8psi/0–3.58*104kgf/m2)
Measurable Temperature -40–+120ºC
Battery Life 5 years +
Size 76 x 56 x 22mm
Weight <38g - no va ve weight
Display Receiver
Worki g Voltage Ra ge Receiver Supp y 5v DC 9–15v DC
Receivi g Se sitivity N/A <-100dBm
Receivi g Freque cy N/A 433.92MHz
Size 83 x 41 x 18mm 75 x 55 x 17mm
Weight 70g 35g
Worki g Curre t Standby - <30mA / A arm - <80mA
Worki g Temperature Ra ge -30 – +80ºC
Sensor Insta ation
> Discharge the whee , press the tyre around the va ve by too to fix the sensor.
> Remove the origina air va ve.
> Insta the sensor - the ho e for air must not be jammed.
> Fix the sensors to the corresponding whee -
No. 1 is fro t left wheel; No. 2 is fro t right wheel; No. 3 is rear right wheel a d No. 4 is rear left wheel
> Insta the tyre and charge it with air to norma pressure, then turn it to ba ance it.
> Insta the whee .
I stallatio
Remove the origina
air va ve.
Ty r e P r e s s u r e M o i t o r i g S y s t e m 7
Fix the sensor.
Charge the tyre to
standard pressure
then ba ance the
whee .
Tighten the screw in
the sensor according
to c ockwise direction
by screwp ate.
I stallatio - co ti ued
8
Recommended
Insta the
disp ay on the
heater vent.
C ip the
bracket
appropriate y if
it is too ong.
Hide and fix
the receiver in
drivers
footwe .
Receiving
antenna
Disp ay bracket - 1 Disp ay bracket - 2
ACC. ON
Recommended
Insta the
disp ay in front
of the
dashboard.
Recommended
Insta the
disp ay in an
easy to see
p ace.
> Connect the red wire to +12 power supp y, white wire to the ACC. ON, b ack wire to ground.
Disp ay and Receiver Insta ation
> Fix the disp ay on a suitab e position with the bracket or 3M sticker.
3M sticker
Operatio
Ty r e P r e s s u r e M o i t o r i g S y s t e m 9
System Operation
The system enters into working status after insta ation. With ACC ON the system starts se f-test then disp ays the inside pressure
and temperature of each tyre for 2 seconds. If a tyres are in good condition, the disp ay wi go off automatica y, the status
indicator (LED) turns green. Otherwise the buzzer wi sound 3 times with the indicator in orange or red and the disp ay wi show the
re evant information, the buzzer wi sound 3 times every 3 minutes unti the prob em is rectified.
Press SCAN to read the data of each tyre.
Press SET 3 seconds to convert the temperature units - ºC to ºF
When the ACC ON cut off the power supp y, the system is sti in monitoring state but wi not a arm
Front right whee Power Sensor signa High temperature Temperature Temperature unit
Rear right whee Air eakage Tyre pressure Pressure unit Status indicator
Front eft
whee
Rear eft
whee
Scan
Set
System A arm
Examp e - when reference pressure is 2.4 bar.
Operatio - co ti ued
10
15% ower than
reference pressure
20% ower than
reference pressure
20% higher than
reference pressure
25% higher than
reference pressure
Temperature higher
than 70ºC
Temperature higher
than 80ºC
Air eaking
No signa
Fau ty sensor
Low battery - sensor
Tabla de contenidos
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario