Brew Monk 017.070.30 Manual de usuario
www.brewmonk.eu
Instruction ManualEN
INSTRUCTION
MANUAL
BREW MONK
CONICAL FERMENTER
Item N°.: 017.070.30
Volume: Up to 32 litre
2
EN - Instruction Manual Brew Monk
Thank you for purchasing the Brew Monk™ Conical Fermenter.
Note: it is important to follow the installation instructions below.
Read all the instructions carefully and keep this manual for future reference.
COMPONENT SHEET
Airlock
Component
1
Quantity
1
Quantity
Ball-valve M12
tightening nut
Component
Airlock bung 1 1
Rotating rack-
ing arm
Thermometer 1 1
3/4’’ Strainer
valve
Thermometer
O-ring (white) 1 3
Detachable
stand
Thermometer
M10
tightening nut
112M6 screw
Ball-valve +
O-ring (black) 112M6 nut
3
Instruction Manual Brew Monk - EN
Put the thermometer into the appropriate hole and tighten it with a M10 nut. It is located at the front of
the fermenter body as shown. Tip: attach the O-ring to the sensor rst.
Put the ball-valve into the provided hole on the conical bottom and tighten it with a M12 nut. It is located
at the front of the fermenter, on the conical part as shown. Tip: insert the rotating arms into the valve
inlet as shown, the racking arm direction can be adjusted by rotating the ball-valve during fermentation.
Seal the strainer valve with some PTFE tape (not included), screw the strainer valve onto strainer pipe as
shown. Tip: make sure the PTFE tape is sealed enough to prevent leakage.
Attach 3 detachable stands with M6 screws and M6 nuts.
ASSEMBLY INSTRUCTIONS
4
www.brewmonk.eu
Distributed by Brouwland
Korspelsesteenweg 86
3581 Beverlo, Belgium
www.brouwland.com
EN - Instruction Manual Brew Monk
• It is very important to prepare and clean the fermenter and accessories before fermentation. We
recommend using cleaning agents like Chemipro Wash and Chemipro San.
• Please ll the fermenter with water up to top and make sure there is no leakage before transferring
the wort to fermenter.
• Do not overll the fermenter (not more than 30 litres of wort), ensure that there is enough headspace
to prevent blow-off.
• Fill the airlock with a small amount of water and put it into the lid, as shown.
• It is very important to clean the fermenter and accessories after every use; the dry ingredients may
stick to the metal. We recommend using a cleaning agent such as Chemipro Wash.
• Do not use any sharp metal utensil to remove any residue. Use a soft cloth or soft scouring pad to
clean the inside of the boiler.
• Suitable cleaning products can be used; we recommend Chemipro Wash and Chemipro San.
• Store the fermenter in a dry place.
• Lock the lid with 4 clamps.
• The fermenter must be positioned on a stable, secure and horizontal support structure prior to use.
FERMENTATION PREPARATION
AFTER FERMENTATION
Tabla de contenidos
Otros manuales de Sistema de elaboración de cerveza de Brew Monk
Brew Monk
Brew Monk 057.700.70 Manual de usuario
Brew Monk
Brew Monk TITAN Manual de usuario
Brew Monk
Brew Monk CONICAL FERMENTER Manual de usuario
Brew Monk
Brew Monk 55 l Manual de usuario
Brew Monk
Brew Monk 057.700.30 Manual de usuario
Brew Monk
Brew Monk B40 Manual de usuario
Brew Monk
Brew Monk B40 Manual de usuario
Manuales populares de Sistema de elaboración de cerveza de otras marcas
Curtis
Curtis ThermoPro G4 Series Manual de usuario
Animo
Animo ComBi CB5 Manual de usuario
MoreBeer
MoreBeer BrewSculpture Manual de usuario
Keurig Hot
Keurig Hot Commercial Series Manual de usuario
Keg King
Keg King KEGMASTER XL Manual de usuario
Blichmann Engineering
Blichmann Engineering BrewEasy Compact TC Instrucciones de instalación