Bresser 433MHz Manual de usuario

WEATHER CENTER

Instruction Manual

GB IE

General Information

About this Instruction Manual

Please read the safety instructions in this manual carefully. To avoid damage to the unit and the risk

of injury, only use this product as described in the manual.

Keep the instruction manual handy so that you can easily look up information on all the functions.

DANGER!

You will ﬁnd this symbol in front of every section of text which deals with the

risk of severe injury or even death in the event of improper use.

CAREFUL!

You will ﬁnd this symbol before every section of text that deals with the risk of

minor to severe injuries resulting from improper use.

NOTE!

You will ﬁnd this symbol in front of every section of text which deals with the

risk of damage to property or the environment.

Intended Use

This product is intended only for private use. It was developed as an electronic medium for the use

of multimedia services.

General Warning

DANGER!

This device contains electronic components which operate via a power source (power supply and/or

batteries). Do not leave children unattended when using the device. Only use the device as described

in the manual, otherwise you run the RISK of an ELECTRIC SHOCK.

Children should only use the device under adult supervision. Keep packaging material (plastic bags,

rubber bands, etc.) out of the reach of children! There is a RISK OF CHOKING!

Keep batteries out of the reach of children! Make sure you insert the batteries correctly. Empty or

damaged batteries could cause burns if they come into contact with the skin. If necessary, wear ade-

quate gloves for protection.

DANGER!

Do not expose the device to high temperatures. Use only the recommended batteries. Do not short

circuit the device or batteries, or throw them into a ﬁre. Excessive heat or improper handling could

trigger a short circuit, ﬁres or even explosions!

NOTE!

Do not disassemble the device. In the event of a defect, please contact your dealer. He will contact the

Service Centre and can send the device in to be repaired, if necessary.

Use only the recommended batteries. Always replace weak or empty batteries with a new, complete

set of batteries at full capacity. Do not use batteries from different brands or with different capacities.

The batteries should be removed from the unit if it has not been used for a long time.

Notes on cleaning

Separate the device from the power supply before cleaning (remove batteries)!

NOTE!

Only use a dry cloth to clean the exterior of the device. Do not use any cleaning ﬂuid to avoid dama-

ging the electronics.

Disposal

Entsorgen Sie die Verpackungsmaterialien sortenrein. Informationen zur ordnungsgemäßen Ent-

sorgung erhalten Sie beim kommunalen Entsorgungsdienstleister oder Umweltamt.

Dispose of the packaging materials properly, according to their type (paper, cardboard, etc).

Contact your local waste disposal service or environmental authority for information on the

proper disposal.

Do not dispose of electronic devices in the household garbage!

As per the Directive 2002/96/EC of the European Parliament on waste electrical and electronic equip-

ment and its adaptation into German law, used electronic devices must be collected separately and

recycled in an environmentally friendly manner.

In accordance with the regulations concerning batteries and rechargeable batteries, disposing of them

in the normal household waste is explicitly forbidden. Please pay attention to dispose of your used

batteries as required by law - at a local collection point or in the retail market (a disposal in domestic

waste violates the Battery Directive).

Batteries that contain toxins are marked with a sign and a chemical symbol. „Cd“ = cadmium, „Hg“

= mercury, „Pb“ = lead.

A D ?

1battery contains cadmium

2battery contains mercury

3battery contains lead

GB/IE

Introduction

Congratulations on your purchase of the BRESSER Weather Center. The weather center consists of

a main console unit with a remote control, as well as an assortment of remote sensors which collect

and transmit a wide range of weather data, including outdoor temperature, humidity, wind speed and

direction, rain amount and rain rate.

Main Console Unit

The main console unit features a radio-controlled atomic precision clock with alarm and weather

forecast. It measures indoor temperature and humidity, and displays weather data collected by the

remote weather sensors. It also provides indication of the indoor/outdoor temperature, pressure and

humidity trends, and celestial information such as moon phase, and sunrise/set times.

Bresser GmbH

DE-46414 Rhede/Westf. · Germany

Remote Weather Sensors

The remote weather sensors include a thermo-hygrometer, anemometer (wind sensor) and rain

sensor. All data collected by the sensors are transmitted to the main console unit by wireless RF,

with a range up to 100 meters (open area). The weather center supports a maximum of

5 thermo-hygrometers, allowing 5 channels of temperature/humidity display.

Thermo-Hygro-Sensor

Wind sensor

Rain sensor

Features

Weather Forecast

- Sunny, Partly Cloudy, Cloudy, Slight Rain, Heavy Rain, Snow and Unstable Weather Conditions

Pressure

- Current or historical pressure (mbar/ hPa, mmHg or inHg)

- Altitude or sea-level pressure adjustment for atmospheric pressure compensation

- Pressure trend indication

- Sea-level pressure history for the last 24 days

- Sea-level pressure history bar chart

Moon Phase

- 12 steps of moon symbols

- Scans moon phase for year 2000 to 2099

- Moon phase history for the last or future 39 days

Radio Controlled Clock

- Time and date synchronized by radio signal DCF-77 to atomic clock precision

(time and date also manually adjustable)

GB/IE

Clock and Calendar (12 hr/ 24 hr) (month/day or day/month)

- Different combinations of clock and calendar displays

- 6 languages for day of week (English/ German/ French/ Italian/ Spanish/ Dutch)

Alarms

- Single alarm: activated once at speciﬁed time

- Weekday alarm: activated everyday from Monday to Friday at speciﬁed time

- Pre-alarm: activated ahead of single or weekday alarm if channel 1 temperature falling to +2ºC or

below (ﬁxed 30 minutes)

- Programmable snooze function (1-15 minutes)

Sunrise Time and Sunset Time

- Calculates sunrise/set times with geographical information provided by user (DST, zone time

offset, latitude, longitude)

- Over 133 preset cities can be selected for automatic geographical information input

Remote Temperate and Relative Humidity, with Trend Indication

- Indoor and outdoor temperature and relative humidity display (ºC or ºF)

- Temperature and relative humidity trend indication

- Dew point display

- Max and Min memory for temperature and relative humidity

Comfort Level Indicator

- Analyzes current environmental conditions (Comfort, Wet and Dry)

Rainfall Measurement

- Records rainfall amount for the last hour, last 24 hours, last day, last week and last month

(inch or mm)

- Daily rainfall alert if rainfall for the current day exceed pre-speciﬁed amount.

Wind

- Temperature at place of anemometer

- Temperature (ºC or ºF) adjusted to wind chill factor

- Wind direction compass display. Wind direction angles available as compass points or bearings

- Average wind speed and gust speed (mph, m/s, knots, and km/h)

- Daily Maximum wind speed and gust speed memory.

- Wind speed alert for average wind speed and wind gust speed

Contents of Complete Weather Center Kit

Before installing your weather center, please check that the following are complete:

Hardware

Components Fittings

Main Console Unit

Thermo-Hygro

Sensor

Rain Sensor:

-Funnel shaped lid

with battery hatch

-Sensor base

-Bucket see-saw

mechanism

-Protective screen

4 screws for

securing unit to

ground

Anemometer (Wind

Sensor):

- Wind cups

- Wind vane

- Anemometer arm

- Anemometer base

4 screws for

securing unit to

vertical surface

GB/IE

Installing your Weather Center

Setting up the Remote Weather Sensors

Before starting up the main console unit, setup all the remote sensors ﬁrst.

When placing the sensors, make sure that they are within receiving range of the console unit.

Ideally, they should be within the line of sight of the console unit. Transmission range may be

affected by trees, metal structures and electronic appliances. Test reception before permanently

mounting your weather center.

Also make sure that the sensors are easily accessible for cleaning and maintenance.

The remote sensors should be cleaned on a weekly basis, since dirt and debris will affect sensor

accuracy.

Setting up the Thermo-Hygro Sensor(s)

1. Open the latch at the base of the thermo-hygro sensor.

2. Set the channel with a slide switch.

3. Insert two 2 x UM-3 or “ AA” size 1.5 V batteries.

4. Use a pin to press the “RESET” key which is in the battery compartment of thermo-hygro

sensors after LED ﬂash.

5. Replace the latch and mount the unit at desired location.

Placement Tips:

- The thermo-hygro sensor should be in an area with free air circulation and sheltered from direct

sunlight and other extreme weather conditions. Place the unit in a shaded area, such as under a

roof.

- Avoid placing the sensor near sources of heat such as chimneys.

- Avoid any areas which collect and radiate heat in the sun, such as metal, brick or concrete

structures, paving, patios and decks.

- Ideally, place the sensor above natural surfaces such as a grassy lawn.

- The international standard height for measurements of air temperature is at 1.25m (4 ft) above

ground level.

Setting up the Rain Sensor

1. Unlock the funnel-shaped top of the rain sensor by turning both knobs on the sides of the rain

sensor in an anti-clockwise direction.

2. Lift the top off the base and insert two 2 x UM-3 or “AA” size 1.5 V batteries into the battery

holder.

3. Replace the lid and secure into place by turning the knobs clockwise.

4. Place the rain sensor in a location such that precipitation can fall directly into the sensor, ideally

2-3 ft above the ground.

It may be secured into place by using the four screws provided.

5. The sensor must be accurately leveled for optimum performance. To check if the sensor is

leveled, remove the lid and check if the ball bearing inside is at the midpoint of the leveler.

Additionally, a bubble level or carpenter’s level may be used.

6. Attach the protective screen onto the top of the lid. The screen will prevent any debris entering

the sensor.

Placement Tips:

- The rain sensor should be placed in an open area away from walls, fences, trees and other

coverings which may either reduce the amount of rainfall into the sensor, deﬂect the entry of wind-

blown rain, or create extra precipitation runoff. Trees and rooftops may also be sources of pollen

and debris.

- To avoid rain shadow effects, place the sensor at a horizontal distance corresponding to two to four

times the height of any nearby obstruction.

- It is important that rain excess can ﬂow freely away from the sensor. Make sure that water does not

collect at the base of the unit.

- The rainfall measurement mechanism utilizes a magnet, hence do not place any magnetic objects

around the proximity of the sensor.

Setting up the Anemometer (Wind Sensor)

1. Assemble the wind cups and wind vane to the anemometer arm

2. Attach the assembled anemometer to the base.

3. Insert two 2 x UM-3 or “AA” size 1.5 V batteries into the battery holder in the base.

4. Mount the anemometer onto a vertical surface, using the ﬁttings provided.

5. To allow the main console unit to ﬁnd the direction which the wind vane is oriented, the

following procedures are required:

i. Insert the batteries

ii. Point the wind vane towards the north. Use a compass or map if necessary.

iii. Use a pin to press the “SET” key which is in the battery compartment of the wind sensor.

Note: Above procedure must be repeated for changing battery.

The “SET” will toggle the direction between two modes:

1. Let the wind direction as manufacturer has designed. It will be as a default setting after

changing the batteries.

2. Set the current direction as NORTH.

Placement Tips:

- Check that wind can travel freely around the anemometer and is not distorted by nearby buildings,

trees or other structures.

- For better results, place the anemometer at least 3m above local structures and obstacles. The

ground creates a frictional effect to wind ﬂow and will attenuate readings.

- Aim for maximum exposure of the anemometer to the commonest wind directions in your area.

- The ofﬁcial mounting location for anemometers is 10m (33 ft) above ground level in a clear

unobstructed location.

GB/IE

Starting up the Main Console Unit

Once the console unit is properly powered, the display will start showing some data and weather

parameters. Wait for a few minutes for the console to ﬁnish self-calibration and for the sensor read-

ings to show up.

If “---” is still displayed for the sensor reading(s), check the wireless transmission path and the bat-

teries for the corresponding sensor.

Setting up the Main Console Unit

1. Open the latch at the back of the main console unit.

2. Insert 4 x UM-3 or “AA” size 1.5 V batteries according to the polarities shown.

3. Reattach the latch.

4. If placing the console unit on a table or horizontal surface, fold out the table stand and adjust to

the optimal viewing angle.

5.If mounting the console unit on a wall or vertical surface, fold the table stand back into the unit

and use the ﬁtting provided.

Placement Tips:

Make sure that the console unit is within the receiving range of all remote sensors. Ideally

sensors should be within the line of sight of the console unit. Transmission range may be affected by

trees, metal structures and electronic appliances. Test reception before permanently mounting your

weather center.

The console unit measures indoor temperature, humidity, pressure and receives signals from all

remote sensors and radio-clock broadcasts. Avoid placing the console unit in the following areas:

- Direct sunlight and surfaces which radiate and emit heat.

- Near heating and ventilation devices, such as heating ducts or air conditioners.

- Areas with interference from wireless devices (such as cordless phones, radio headsets, baby

listening devices) and electronic appliances.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Estación meteorológica de Bresser

Bresser

Bresser TemeoTrend LB Manual de usuario

Bresser

Bresser Thermo Hygro Quadro NLX Manual de usuario

Bresser

Bresser MyTime Crystal P Colour Manual de usuario

Bresser

Bresser TemeoTrend LB Manual de usuario

Bresser

Bresser 7002531 Manual de usuario

Bresser

Bresser 7902585 Manual de usuario

Bresser

Bresser FREEK VONK 9820200 Manual de usuario

Bresser

Bresser MyClimate Thermo-Hygro Manual de usuario

Bresser

Bresser ClimaTemp TB Manual de usuario

Bresser

Bresser Temeo Hygro Quadro DLX Manual de usuario

Bresser

Bresser P7002560 Manual de usuario

Bresser

Bresser 4Cast NG Manual de usuario

Bresser

Bresser ClimaTemp WS Manual de usuario

Bresser

Bresser 4Cast PRO SF Manual de usuario

Bresser

Bresser Meteotime Manual de usuario

Bresser

Bresser Thermo Hygro Quadro NLX Manual de instrucciones

Bresser

Bresser 7002550 Manual de usuario

Bresser

Bresser ClimateTemp NDH Manual de usuario

Bresser

Bresser Quadro-NG-Thermo-Hygro Manual de usuario

Bresser

Bresser WIFI ClearView Weather Station 7in1 Manual de usuario

Bresser

Bresser ClimaTrend Hygro Quadro Manual de usuario

Bresser

Bresser TemeoTrend NBF Manual de usuario

Bresser

Bresser Climate Monitor Manual de usuario

Bresser

Bresser Thermo Hygro Quadro Neo Manual de usuario

Manuales populares de Estación meteorológica de otras marcas

Auriol

Auriol AHFL 433 A1 Manual de usuario

NexSens

NexSens G2-HYDROMET Manual de usuario

Hyundai

Hyundai WS 2202 Manual de usuario

IROX

IROX HBVR761 UV-X Manual de usuario

La Crosse Technology

La Crosse Technology C86371 Manual de usuario

ADE

ADE WS 1711 Manual de usuario

Auriol

Auriol z29592 Manual de usuario

Auriol

Auriol 296289 Manual de usuario

Hyundai

Hyundai WS 2266 Manual de usuario

La Crosse Technology

La Crosse Technology WS-2210 Manual de usuario

La Crosse Technology

La Crosse Technology WS-811561 Manual de usuario

Ventus

Ventus W177 Manual de usuario

National Geographic

National Geographic VA Colour RC Manual de usuario

Renkforce

Renkforce 1208067 Manual de usuario

Levenhuk

Levenhuk Discovery Report WA40 Manual de usuario

Instant Transmission

Instant Transmission MA 10410 Manual de usuario

Lutron Electronics

Lutron Electronics PHB-318 Manual de usuario

WAREMA

WAREMA EWFS Weather station eco Manual de usuario