Braeburn 1020 Instrucciones de uso

This thermostat requires 24 Volt AC Power or two (2) properly installed

“AA” Alkaline batteries for proper operation. When connecting 24 Volt

AC Power the batteries may be installed as a backup.

For use only as described in this manual. Any other use

will void warranty.

1020

Single Stage Heat / Cool

Conventional and Heat Pump

Speciﬁcations

About Your Thermostat

Installation

System Testing

Setting User Options

Operating Your Thermostat

Additional Operation Features

Thermostat Maintenance

Warning

Turn off power to the heating or cooling

equipment before installation.

Attention

For installation by experienced service

technicians only.

1220

Up to 2 Heat / 2 Cool

Conventional and Heat Pump

Read all instructions before proceeding.

This thermostat is compatible with:

  •Singlestageheat/coolconventionalandheatpumpsystems

  •Conventionalsystemsupto2heat/2cool(1220only)

  •

Singlecompressorheatpumpsystemswithanauxiliaryheatstage(1220only)

  •250–750millivoltheatonlysystems

Electrical and control speciﬁcations:

  •ElectricalRating:24VoltAC

  •1ampmaximumloadperterminal

  •ACPower:18–30VoltsAC

  •DCPower:3.0VoltDC(2“AA”AlkalineBatteriesIncluded)

  •ControlRange:45°–90°F(7°–32°C)

  •TemperatureAccuracy:+/-1°F(+/-.5°C)

Terminations

  •1020–Rc,Rh,O,B,Y1,W1,G,C

  •1220–Rc,Rh,O,B,Y1,Y2,E/W1,G,W2,C

Speciﬁcations

1020W-100-01

Model number is located on back of thermostat

Non-Programmable

Thermostats

Detailed

Installer Guide

Single Stage Heat / Cool

Conventional and Heat Pump

Setting User Options

Operating Your Thermostat

Additional Operation Features

Thermostat Maintenance

For installation by experienced service

technicians only.

Up to 2 Heat / 2 Cool

Conventional and Heat Pump

Read all instructions before proceeding.

About Your Thermostat

Room Temperature...........Displaysthecurrentroomtemperature

Reset Button.....................

Resetsthermostatbacktofactorydefaults

Low Battery Indicator......Indicateswhenthebatteriesneedto

  bereplaced

System Switch..................

Selectssystempreference

Quick Reference

Instructions ......................Storedinslotattopofthermostat

Fan Indicator....................Indicateswhenthesystemfanisrunning

System Status Indicator...Displaysinformationaboutthestatusof

   thesystem

Arrow Buttons..................Usedtoincreaseordecreasesettings

Set Temperature...............Displaysthecurrentsetpointtemperature

Fan Switch........................Selectsthesystemfanmode

Battery Compartment...............Locatedinthebackofthethermostat

Installation

Warning

Disconnect power before beginning installation.

Thermostat Location

Installthethermostatapproximately5feet(1.5m)abovetheoorinan

areathathasagoodamountofaircirculationandmaintainsanaverage

roomtemperature.

Avoidinstallationinlocationswherethethermostatcanbeaffectedby

drafts,deadairspots,hotorcoldairducts,sunlight,appliances,concealed

pipes,chimneysandoutsidewalls.

410

Install your new Braeburn thermostat in 5 basic steps:

1 InstalltheSub-Base

2 ProvidePower

3 ConnectYourWires

4 SetInstallerSwitches

5 AttachThermostattoSub-Base

Install the Sub-Base:

•Removethesub-basefromthebodyofthethermostat.

•Mountthesub-baseasshownbelow:

NOTE: After sub-base installation, you may insert the quick reference card

into the slot on the top of the base.

Provide Power

•For 24 Volt AC power,youmustconnectthecommonsideofthetrans-

 formertotheCterminalonthethermostatsub-base.

•For primary or back-up power,insertthe2supplied“AA”typealkaline

 batteriesintothebatterycompartmentlocatedintherearhousingofthe

 thermostat.MakesuretopositionthePositive(+)andNegative(-)sides

 ofthebatteriescorrectlywiththe+/-symbolsinthebatterycompartment.

24VAC Power

Terminal (C)

Drill 3/16” pilot holes in

your desired location.

Use supplied anchors for

drywall or plaster.

UP UP

Terminal Function Description

 Rc   Input 24VoltACCoolingTransformer

       (DualTransformerSystemsOnly)

 Rh   Input PowerConnection(24VoltACHeating

       TransformerorMillivoltPowerSource)

 O   Output ReversingValve(CoolActive)

 B   Output ReversingValve(HeatActive)

 Y1   Output CompressorRelay

 G   Output FanControl

 W1   Output ConventionalHeatRelay

 C   Input 24VoltACTransformerCommon

Connect Your Wires

Wiring Terminations

Terminal Function Description

W1/E   Output (W1)1stStageConventionalHeat

(E)EmergencyHeatRelay

  Y2   Output

2ndStageConventionalCoolingCompressor

  W2   Output 2ndStageHeat/AuxiliaryHeat

Additional Terminations (1220 only)

Heat Only or Millivolt

Set Installer Switch to CONV

Rh PowerConnection

W1 HeatRelay(appearsasW1/Eon1220)

1 HEAT / 1 COOL Single or Dual Transformer

Set Installer Switch to CONV

24VoltACPower(heatingtransformer)[note 2]

24VoltACPower(coolingtransformer)[note 2]

W1 HeatRelay(appearsasW1/Eon1220)

Y1 CompressorRelay

G FanRelay

C 24VoltACTransformerCommon[note 1, 3]

Typical Wiring Conﬁgurations

NOTE: The “Installer Switch” option will be conﬁgured in the next step.

Conventional Systems

NOTES - Conventional Systems

[1]Ifbatteriesareinstalledthe24VoltACcommonconnectionisoptional

[2]Removefactoryinstalledjumperfordualtransformersystems

[3]Indualtransformersystems,transformercommonmustcomefrom

 coolingtransformer

[4]ConnectY2onlyifasecondcoolingcompressorisbeingused

Provide disconnect and overload protection as required.

2 HEAT / 2 COOL Single or Dual Transformer (1220 Only)

Set System Type to CONV

24VoltACPower(heatingtransformer)[note 2]

24VoltACPower(coolingtransformer)[note 2]

W1 HeatRelayStage1

W2 HeatRelayStage2

Y1 CompressorRelayStage1

Y2 CompressorRelayStage2 [note 4]

G FanRelay

C 24VoltACTransformerCommon[note 1, 3]

Conventional Systems (cont.)

Typical Wiring Conﬁgurations

NOTE: The “Installer Switch” option will be conﬁgured in the next step.

Heat Pump Systems

1 HEAT / 1 COOL - No Auxiliary Heat

Set Installer Switch to HP

Rh 24VoltACPower

Rc ConnectedtoRhwithsuppliedJumperWire

O or B

 ChangeoverValve [note 2]

Y1 CompressorRelay

G FanRelay

C 24VoltACTransformerCommon [note 1]

2 HEAT / 1 COOL - Including Auxiliary Heat (1220 only)

Set Installer Switch to HP

Rh 24VoltACPower

Rc ConnectedtoRhwithsuppliedJumperWire

O or B

 ChangeoverValve[note 2]

CompressorRelay(1ststageheating/cooling)

W2 AuxiliaryHeatRelay(2ndstageheating)[note 3]

E EmergencyHeatRelay [note 3]

G FanRelay

C 24VoltACTransformerCommon [note1]

Factory Setting

Switch Default Options Comments

Heat Pump Systems (cont.)

NOTES - Heat Pump Systems

[1]Ifbatteriesareinstalledthe24VoltACcommonconnectionisoptional.

[2]SelectOforcoolactiveor Bforheatactive.

[3]InstallaeldsuppliedjumperbetweentheW2 and Eterminalsif

 thereisnoseparateemergencyheatrelayinstalled.

Provide disconnect and overload protection as required.

 CONV/HP CONV

 F/C F

 HE/HG HG

Set Installer Switches

 CONV Selectforconventionalsystems

 HP Selectforheatpumpsystems

 F Selectforfahrenheittemperaturescale

 C Selectforcelsiustemperaturescale

 HG Selectforgasheat

 HE Selectforelectricheat

Attach Thermostat to Sub-Base

1.Lineupthethermostatbodywiththesub-base.

2.Carefullypushthethermostatbodyagainstthesub-baseuntilitsnaps

 intoplace.

3.Insertquickreferencecardintoslotontopofthermostat.

NOTE: Installer switches are located on the back of the thermostat. The

reset button must be pressed after making any changes to these switches.

UP UP

System Testing

Warning

Read Before Testing

• Donotshort(orjumper)acrossterminalsonthegasvalveoratthe

 heatingorcoolingsystemcontrolboardtotestthethermostatinstalla-

 tion.Thiscoulddamagethethermostatandvoidthewarranty.

• DonotselecttheCOOLmodeofoperationiftheoutsidetemperature

 isbelow50ºF(10ºC).Thiscouldpossiblydamagethecontrolledcool-

 ingsystemandmaycausepersonalinjury.

• Thisthermostatincludesanautomaticcompressorprotectionfeatureto

 avoidpotentialdamagetothecompressorfromshortcycling.When

 testingthesystem,makesuretotakethisdelayintoaccount.

NOTE: The compressor delay can be bypassed by pressing the reset button

on the front of the thermostat. All user settings will be returned to factory

default.

1 MovetheSYSTEMswitchtoHEATmode.

2 Presstoraisethesettemperatureaminimumof3degreesabove

thecurrentroomtemperature.Thesystemshouldstartwithinafew

 seconds.Withagasheatingsystem,thefanmaynotstartrightaway.

3 MovetheSYSTEMswitchtotheOFFmode.Allowtheheatingsystemto

 fullyshutdown.

4 MovetheSYSTEMswitchtotheCOOLmode.

5 Presstolowerthesettemperatureaminimumof3degreesbelow

thecurrentroomtemperature.Thesystemshouldstartwithinafew

 seconds(unlesscompressorshortcycleprotectionisactive–See

 noteabove).

6 MovetheSYSTEMswitchtotheOFFmode.Allowthecoolingsystemto

 fullyshutdown.

7 MovetheFANswitchtotheONmode.Thesystemfanshouldstart

 withinafewseconds.

8 MovetheFANswitchtotheAUTOmode.Allowthesystemfanto

 turnoff.

Setting User Options

Advanced User Options

Useroptionsallowyoutocustomizesomeofyourthermostatsfeatures.

Thedefaultuseroptionsarecompatiblewithmostapplications,thereforeit

isnotrequiredthatyouadjustthem.

To access the User Options menu, hold down both the and buttons

for approximately 3 seconds until the screen changes and displays

the ﬁrst User Option.

PresstheorbuttontochangethesettingforthedisplayedUserOption.

Afteryouhavemadeyourdesiredsetting,pressandtogetherto

advancetothenextUserOption.

Thethermostatwillreturntonormalmodeafteryourlastuseroptionis

madeorafternokeyshavebeenpressedfor15seconds.

User Factory Setting

No. Options Default Options Comments

 1 1ststage

0.5

0.5, 1.0

Selecta1ststagetemperature

   differential  

or 2.0 differentialof.5˚,1˚or2˚F(.25˚,5˚

       or2˚C)

 2 2ndstage

2.0

1.0, 2.0,

 Selecta2ndstagetemperature

   differential  

3.0, 4.0

, differentialof1˚,2˚,3˚,4˚,5˚or6˚F

 (1220Only)

5.0 or 6.0

 (.5˚,1˚,1.5˚,2˚,2.5˚or3˚C)

Table of User Options

Detailed Explanation of User Options:

Temperature Differential

(User Option 1 and 2)

Thedifferentialsettingisthetemperaturecontrolrangethatyourthermostat

willprovide.Thesmallerthesetting,thetighteryourrangeoftemperature

controlandcomfortwillbe.The2ndstagedifferentialisonlyforsystems

withasecondstageofheating(auxiliaryheat).

Operating Your Thermostat

Setting the System Control Mode

TheSystemControlhasseveralmodesofoperationthatcanbeselectedby

movingtheSYSTEMswitchtotheappropriateposition.

COOL Onlyyourcoolingsystemwilloperate

OFF Heatingandcoolingsystemsareoff.

HEAT Onlyyourheatingsystemwilloperate.

Additional Switch Position (Model 1220 Only):

EMER Operatesabackupheatsource(EmergencyHeat)forheatpump

 systemsonly.

NOTE: If your model 1220 was conﬁgured for a

conventional system (CONV) then you will not have

the EMER (emergency heat) option and “NO EMER

SET” will ﬂash in the display if EMER is selected

with the system switch.

Setting the Fan Control Mode

The Fan Control has 2 modes of operation – AUTO

and ON. The mode can be selected by moving the

FAN switch to the appropriate position.

AUTO Thesystemfanwillrunonlywhenyour

  heatingorcoolingsystemisrunning.

ON Thesystemwillruncontinually.

Detailed Explanation of User Options:

Temperature Differential

(User Option 1 and 2)

Thedifferentialsettingisthetemperaturecontrolrangethatyourthermostat

willprovide.Thesmallerthesetting,thetighteryourrangeoftemperature

controlandcomfortwillbe.The2ndstagedifferentialisonlyforsystems

withasecondstageofheating(auxiliaryheat).

Temperature Adjustment

Presstheorbuttontoadjustthecurrentsetpointtemperature.

Status Indicators

Statusindicatorsappearinthedisplaytolet

youknowifyoursystemisheating,cooling

oroff.

HEAT ON

Indicatesyourheatingsystemisrunning.

COOL ON

Indicatesyourcoolingsystemisrunning.

Additional Status Indicators (Model 1220 Only):

AUX Indicatesthattheauxiliarystageofheatingisrunning

 (Multi-StageSystemsonly).

EMER Indicatesthattheemergencyheatingsystemisrunning 

 (HeatPumpSystemsonly).

Resetting the Thermostat

Thisthermostatprovidesyouwitharesetbuttonthatwilleraseallofyour

usersettingsandprogramming.

Toresetthethermostat,useasmallobjectsuchasatoothpickorpaper-

clipandgentlypressthebuttonlocatedinsidethesmallholeonthefrontof

thethermostathousinglabeled“reset”.

Additional Operation Features

Compressor Protection

Thisthermostatincludesanautomaticcompressorprotectiondelayto

avoidpotentialdamagetoyoursystemfromshortcycling.Thisfeature

activatesashortdelayafterturningoffthesystemcompressor.

Thermostat Maintenance

Changing the Batteries

Dependingonyourparticularinstallation,this

thermostatmaybeequippedwithtwo(2)“AA”

typealkalinebatteries.

If batteries are installed and they become low,

a low battery indicator will appear in the display.

You

shouldchangeyourbatteriesimmediately

whenyouseethelowbatterysignalbyfollowing

theseinstructions.

1.Removethermostatbodybygentlypullingitfrombase.

2.Removeoldbatteriesandreplacewithnewbatteries.

3.Makesuretocorrectlypositionthe(+)and(-)symbols.

4.Gentlypushthermostatbodybackontobase.

Thermostat Cleaning

Neversprayanyliquiddirectlyonthethermostat.Usingasoftdampcloth

wipetheouterbodyofthethermostat.Neveruseanyabrasivecleansersto

cleanyourthermostat.

For troubleshooting tips, visit braeburnonline.com.

BraeburnSystemsLLC

2215CornellAvenue•Montgomery,IL60538

TechnicalAssistance:www.braeburnonline.com

Callustoll-free:866-268-5599(U.S.)

630-844-1968(OutsidetheU.S.)

PatentsPending•1020W-100-001

Store this manual for future reference

YEAR

WARRANT Y

LIMITED

Limited Warranty

Wheninstalledbyaprofessionalcontractor,thisproductisbackedbya5year

limitedwarranty.Limitationsapply.Forlimitations,termsandconditions,you

mayobtainafullcopyofthiswarranty:

·Visitusonline:www.braeburnonline.com/warranty

·Phoneus:866.268.5599

·Writeus:BraeburnSystemsLLC

2215CornellAvenue

MontgomeryIL60538

Otros manuales para 1020

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Termostato de Braeburn

Braeburn

Braeburn 3000 Manual de usuario

Braeburn

Braeburn Premier 5000 Manual de usuario

Braeburn

Braeburn Premier 3300 Manual de usuario

Braeburn

Braeburn Premier 5100 Manual de usuario

Braeburn

Braeburn Builder 1000 Manual de usuario

Braeburn

Braeburn 7300 Manual de usuario

Braeburn

Braeburn 2220 Manual de usuario

Braeburn

Braeburn Premier Series Manual de usuario

Braeburn

Braeburn Builder 1200NC Manual de operación y mantenimiento

Braeburn

Braeburn 5020 Instrucciones de uso

Braeburn

Braeburn 1025NC Manual de operación y mantenimiento

Braeburn

Braeburn Premier 5300 Manual de usuario

Braeburn

Braeburn 1020 Instrucciones de montaje

Braeburn

Braeburn Builder 1000NC Manual de usuario

Braeburn

Braeburn 229100 Manual de usuario

Braeburn

Braeburn 2020 Manual de operación y mantenimiento

Braeburn

Braeburn 2020NC Manual de operación y mantenimiento

Braeburn

Braeburn 1100 Builder Series Manual de usuario

Braeburn

Braeburn Premier Series Manual de usuario

Braeburn

Braeburn 1025NC Manual de usuario

Braeburn

Braeburn 7320 Manual de usuario

Braeburn

Braeburn 6100 Instrucciones de montaje

Braeburn

Braeburn 5200 Manual de usuario

Braeburn

Braeburn BlueLink 7205 Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario