B+B SmartWorx ICR-1601 Guía
Start Guide
ICR-1601
Start Guide
Safety Instructions
Please take care to following instructions:
•Use the router in compliance with national and international law and in compliance with
any special or additional restrictions regulating use of the router in the various applica-
tions and environments.
•To avoid possible injury and/or damage to the device, observe the relevant provisions
and standards. Use only the original accessories as recommended. Unauthorized de-
vice or accessory modification, or using accessories that have not been approved can
result in router damage and/or violation of the regulations.
•Unauthorized device or accessory modification or using the accessories that have not
been approved can result in warranty termination.
•Do not open the router.
•Caution! The SIM card can be swallowed by small children.
•When connecting the device to a power supply do not exceed the defined voltage.
•Do not expose the router to extreme ambient conditions. Protect the router against dust,
moisture, and high temperature.
•It is recommended that you do not use the router at petrol filling stations. We recommend
observing local restrictions concerning the use of radio-based devices while working with
explosive material for example, at petrol filling stations, or in chemical plants.
•While using the router close to personal medical devices, such as cardiac pacemakers
or hearing aids, proceed with heightened caution.
•Operating the router too close to TV sets, radio receivers, personal computers, or tele-
phones can cause interference.
•It is recommended that you create a copy or backup of the important settings stored in
the memory of the router.
QSG-0005-EN, July 20, 2018 1Released in the Czech Republic
Start Guide
Product Disposal Instructions
The WEEE (Waste Electrical and Electronic Equipment: 2012/19/EU) direc-
tive has been introduced to ensure that electrical/electronic products are recy-
cled using the best available recovery techniques to minimize the impact on
the environment. This product contains high quality materials and components
which can be recycled. At the end of its life this product MUST NOT be mixed
with other commercial waste for disposal. Check with the terms and conditions
of your supplier for disposal information.
QSG-0005-EN, July 20, 2018 2Released in the Czech Republic
Start Guide
First Use
Before applying power to the router, connect the components that you required for your
applications. You cannot operate the router without connected antenna, inserted SIM card,
nor connected power supply.
If you do not have connected main antenna during operation of the router, the router can
be damaged!
1. Antenna
Use a SMA connector to connect the antennas to the router. The main antenna is con-
nected to the router by screwing on the ANT connector (see Figure below). The second diver-
sity antenna can also be connected to the DIV connector to improve performance.
2. SIM Card
The SIM card reader, for 3 V and 1.8 V SIM cards, is located on the front panel of the
router. If you intend to use this device to communicate over a cellular network, please place
an activated data-provisioned SIM card with an unblocked PIN into the SIM card reader. Push
your SIM card into the SIM1 or SIM2 slot until it clicks in place.
QSG-0005-EN, July 20, 2018 3Released in the Czech Republic
Start Guide
Before handling of the SIM card disconnect the router from power supply!
3. Power
The router requires an external DC power supply. The DC voltage required is between
+5 to +18 V DC. Please connect the power adapter DC 5 V/2 A to the PWR connector on the
panel of the router (see figure below).
QSG-0005-EN, July 20, 2018 4Released in the Czech Republic
Start Guide
4. Ethernet
An Ethernet cable may be connected to the LAN1 connector on the front panel (see Figure
above). By default, the Ethernet port is configured as follows:
Connector Purpose Default Setting
LAN1 LAN port (default)
Connect your laptop or PC to this port to
get a local web-server for device configu-
ration and diagnostics.
DHCP Server
IP Address: 192.168.1.1
NetMask: 255.255.255.0
Configuration
1. Configuring the Device Using the Web Browser
You can access the router for status monitoring, configuration, and administration after en-
tering the IP address of the router into the web interface. The default IP address is 192.168.1.1
(netmask 255.255.255.0). Configuration access is allowed for the user "admin" with the initial
password "admin". Attention, it is necessary to use HTTPS protocol for secure communication
over a network! For a detailed description and examples of the router configurations, see the
Configuration Manual.
2. Restoring and Backing up the Router Configuration
After you reset the router, the current configuration is overwritten by the default settings.
We recommend that you back up the router configuration before resetting the device. Refer to
the Configuration Manual for more information.
When the Status LED starts blinking, it is possible to restore the default configuration of the
router by pressing the Reset button on the panel continuously for 6 seconds. After pressing
this button, the default configuration is restored and then the router reboots.
After logging on to the device for the first time, we strongly recommend to change
the default password due to security reasons.
QSG-0005-EN, July 20, 2018 5Released in the Czech Republic
Start Guide
Documentation
User’s Manual, Configuration Manual and manual for each expansion port can be found
and downloaded on this web site: www.advantech-bb.cz/download
Hereby, Advantech B+B SmartWorx s.r.o. declares that the radio equipment type
ICR-1601 is in compliance with Directive 2014/53/EU.
The full text of the EU Declaration of Conformity is available at the following internet
address: www.advantech-bb.cz/eudoc
QSG-0005-EN, July 20, 2018 6Released in the Czech Republic
Otros manuales para ICR-1601
1
Tabla de contenidos
Otros manuales de Enrutador de red de B+B SmartWorx
B+B SmartWorx
B+B SmartWorx SPECTRE v3 LTE Manual de usuario
B+B SmartWorx
B+B SmartWorx UCR11 v2 Manual de usuario
B+B SmartWorx
B+B SmartWorx SmartFlex Hoja de instrucciones
B+B SmartWorx
B+B SmartWorx CR10 v2 Manual de usuario
B+B SmartWorx
B+B SmartWorx SmartFlex SR300 Manual de usuario
B+B SmartWorx
B+B SmartWorx UR5i v2 Libratum Manual de usuario
B+B SmartWorx
B+B SmartWorx ICR-1601 Manual de usuario
B+B SmartWorx
B+B SmartWorx spectre lte Manual de usuario
B+B SmartWorx
B+B SmartWorx RR75i v2 Manual de usuario
B+B SmartWorx
B+B SmartWorx UR5i v2 Libratum Guía
B+B SmartWorx
B+B SmartWorx LR77 v2 Libratum Manual de usuario
B+B SmartWorx
B+B SmartWorx ESWP205-1SFP-T Manual de usuario
B+B SmartWorx
B+B SmartWorx SE400 Series Manual de usuario
B+B SmartWorx
B+B SmartWorx V3 Hoja de instrucciones
B+B SmartWorx
B+B SmartWorx SmartFlex SR300 Manual de usuario
B+B SmartWorx
B+B SmartWorx CR10 v2 Guía
B+B SmartWorx
B+B SmartWorx SmartStart SL301 Manual de usuario
B+B SmartWorx
B+B SmartWorx ABDN-ER-IN501 Series Manual de usuario
Manuales populares de Enrutador de red de otras marcas
NETGEAR
NETGEAR FS526T - Switch Manual de usuario
Korenix
Korenix JetNet 5710G Series Manual de usuario
Automated Logic
Automated Logic ZN551 Manual del propietario
Cisco
Cisco ASR 1000 Series Manual del operador
EnGenius
EnGenius ESR-9710 Manual de usuario
Cisco
Cisco 805 Series Instrucciones de funcionamiento y seguridad