Bose SoundLink Bluetooth Mobile Speaker II Instrucciones de funcionamiento

If your Bluetooth device will not reconnect to the speaker,

try the following to pair your device:

If your device asks for a passcode to connect, make sure the one you entered is

correct. If you never set a passcode, enter 0000 (four zeros)

Make sure Bluetooth is turned ON on your device

Try moving your device closer to the speaker. Bluetooth range is about 9 metres.

Range is reduced when interference is present, like walls or multiple Bluetooth

devices in the same area

If two Bluetooth devices are already paired to the speaker, disable Bluetooth on one

of the devices, or take it out of range of the speaker. The speaker remembers the

last eight paired devices but can only pair to two devices at a time

Repeatedly press the speaker's Bluetooth button until you hear the name of the

desired device

Go to the Bluetooth settings on your device, select the SoundLink® speaker and

choose to "Forget" or "Remove" the speaker. Next, briefly hold the Bluetooth

button on the speaker until the Bluetooth light begins flashing Blue. Try again to

pair the device to the speaker

Reset the device you are trying to pair. This is typically done by

rebooting/restarting it or removing the battery and/or power cable for one minute

Clear the SoundLink® speaker's paired device memory by holding the Bluetooth

button until you hear a tone and, if enabled, a voice prompt. The speaker's

Bluetooth light begins flashing Blue. Try again to pair the device to the speaker

Reset the speaker by turning it on and then holding the power button for 10

seconds until it turns off

A factory reset clears the speaker's language setting and its paired mobile device

memory, returning the speaker to original factory settings. Once reset, turn the

speaker on and try again to pair the device.

Try pairing another device. If the other device works, there may be an issue with

the first device

Difficulty using Party and Stereo modes

Applies to:

•SoundLink Micro Bluetooth® speaker

Please try the following steps if you are having trouble using the Party and Stereo

feature:

Use the Connect app to pair speakers

Party and Stereo modes can be enabled either by using the Bose® Connect app or

manual pairing using the speaker buttons. However, the Connect app pairing

method is strongly recommended for two reasons:

•The procedure on the Connect app is designed to be user friendly

•The Connect app allows any combination of compatible speakers to enter

Party or Stereo modes. (For example, a Revolve and a Revolve+ can be

paired together.) The manual method of using the speaker buttons only

allows you to pair two of the same speaker model

Make sure only one speaker is actively connected to the mobile device.

Stereo and Party mode will not work if both speakers are connected to the mobile

device

Check software versions

The software needs to be up to date, as do both speakers, when using Party and

Stereo modes. If there is a mismatch of two speakers running on different firmware

versions, it can result in difficulty pairing

Try pausing audio when engaging Party or Stereo modes

Pause audio streaming to all speakers before turning on Party or Stereo mode

Rename the speakers in the Connect app 
For ease of use, it is recommended for customers with two of the same model 
speaker to rename the speakers in the Connect app so that they do not share the 
exact same name 
Perform a factory reset. 
For information on performing a reset, see Resetting the speaker. 
Note: A reset is used to correct occasional product issues. It is not something that a 
product should require repeatedly. 
 
 
Speaker will not turn on when using battery 
Applies to: 
•SoundLink Color Bluetooth® speaker II 
•SoundLink Revolve Bluetooth® speaker 
•SoundLink Revolve+ Bluetooth® speaker 
•SoundLink Micro Bluetooth® speaker 
Connect the speaker with its charging cable to a USB charger or a powered 
computer USB port. You may need to do this for the following reasons: 
The battery may not be sufficiently charged. The battery must have sufficient 
charge to power up the speaker 
The speaker has been disconnected from power and unused for 14 days. When this 
happens, it goes into battery protection mode. Brand new speakers are typically in 
this mode when they're first removed from the box 
The speaker is unplugged and unused for more than three days with a remaining 
charge of less than 10%. When this happens, it also goes into battery protection 
mode 
If your speaker still does not turn on after connecting it to power, see Speaker will 
not turn on when connected to AC power 